Controls Citroën C4 96554964XT 6242HL

€48.00

Stellantis CITROEN PEUGEOT
96554964XT 6242HL 624348 NFP

5 in stock

Description

Steering column stalk controls VALEO CITROEN C4 PICASSO and GRAND PICASSO
They control the fog lights, front and rear wipers, wiper sensor and onboard computer

Part description

Used VALEO steering column controls for Citroën vehicles are used to operate the fog lights, front and rear wipers, wiper sensor function and onboard computer. They are a suitable choice when replacing damaged stalks or controls that do not respond reliably when switched.

When selecting a part, pay particular attention to the markings 96554964XT, 6242HL and 624348 and ensure that its design matches the original part. The model name alone is not enough: the connectors, mounting and functions of the individual stalks are also important. Choosing the right part will preserve convenient operation of the listed functions directly from beneath the steering wheel.

Technical information

  • Manufacturer: VALEO
  • Model: Citroën C4; Citroën C4 PICASSO. CITROEN C4 GRAND PICASSO is also listed in the long description.
  • Other numbers: 624348; the designation NFP is also listed in the source materials.
  • Part type: steering column controls – stalks
  • Controlled functions: fog lights, front and rear wipers, wiper sensor, onboard computer
  • Condition: used car part
  • Years and engine types: not specified

Product codes

  • Product codes: 96554964XT, 6242HL, 624348
  • Additional designation: NFP

Before ordering, compare the marking on the original control with the codes listed. Also check that the functions, symbols on the stalks and electrical connectors match.

Installation recommendations

In general, the following applies to this type of part: the exact removal and installation procedure depends on the specific model and vehicle configuration. The steps below are a general procedure for replacing the steering column controls, not a model-specific service guide. If replacement requires work on the steering wheel or airbag system, have this part of the job carried out by a qualified mechanic.

1) Before installation

  • Compare the product marking, assembly shape, mounting, connectors and stalk functions with the old part.
  • Inspect the housing, clips and contacts. Look for cracks, deformation, corrosion, and signs of overheating or moisture.
  • Gently test the movement of the stalks and switches. Do not force the mechanism.
  • Check the cause of the fault: similar symptoms can also be caused by wiring, a connector or a related electrical circuit.

2) Required tools and materials

  • Standard hand tools with the appropriate bits for the fasteners used.
  • Plastic tools for carefully removing covers.
  • A flashlight, clean cloth and supplies for labeling wiring or keeping screws organized.
  • Service procedure for the specific vehicle; suitable automotive diagnostic equipment if needed.

3) Step-by-step installation procedure

  1. Park the vehicle in a safe place, secure it against movement, and switch off the ignition and electrical accessories.
  2. Following the manufacturer’s service procedure, allow the electronics to enter standby mode, disconnect the battery and observe the specified waiting time for safe working.
  3. Carefully remove the covers needed to access the controls. Do not force them off; first locate all screws and clips.
  4. If access requires removing the steering wheel or airbag, proceed only in accordance with the relevant service procedure and if you have the necessary expertise. Do not test airbag connectors with an ordinary test light or multimeter.
  5. Record the wiring layout and connector positions, for example by taking a photo, so everything can be returned to its original arrangement.
  6. Release the connector locks and disconnect them by holding their housings. Do not pull on the wires.
  7. Release the original assembly’s fasteners and carefully remove it. If a rotary contact component is exposed during the work, do not alter its position without authorization.
  8. Compare the removed part with the replacement once again. Check the mating surfaces, mounting and condition of the surrounding wiring.
  9. Fit the replacement controls without using force and secure them in accordance with the manufacturer’s procedure. Plastic parts must not be deformed by overtightening.
  10. Connect the connectors until they are properly secured and route the wiring so that it is not pinched, stretched or in contact with moving parts.
  11. Refit the removed components and covers. Reconnect the battery in accordance with the manufacturer’s procedure and carry out the prescribed steps to restore the electronics to operation.

4) Checks after installation and function verification

  • With the vehicle stationary, first check all listed functions: fog lights, front and rear wipers, wiper sensor controls and onboard computer, as applicable to the vehicle’s equipment.
  • Test the wipers on a wet windshield. Check the sensor function under the appropriate conditions, as described in the vehicle manual.
  • Check that the stalks move freely, the covers are seated correctly, and no unusual messages or warning lights appear.
  • Only take a short test drive after successfully completing the stationary checks. Diagnose any persistent faults rather than repeatedly replacing parts without identifying the cause.

5) Most common installation errors and how to avoid them

  • Choosing a part based only on the car model: also compare the codes, connectors and range of functions of the original stalks.
  • Disconnecting connectors by pulling on the wires: release the clip first and hold the connector housing.
  • Wiring pinched under a cover: check the wiring route and ensure there is enough space before refitting the covers.
  • Forcing the part into place or overtightening the fasteners: if there is resistance, check the position of the part and clips; do not use greater force.
  • Failing to disconnect the power supply safely: always follow the manufacturer’s procedure, especially when working near the airbag system.

Reasons why the part may become damaged

The following causes of damage may generally occur with steering column controls. This is not a description of any defects identified on this specific part.

  • Mechanical wear: frequent use gradually puts strain on the switching mechanisms, detents and contacts.
  • Excessive force when operating: rough handling or an impact to a stalk can damage the plastic parts and internal mechanism.
  • Moisture and dirt: these can impair the movement of the controls or cause corrosion of the electrical contacts.
  • Damaged electrical connections: a loose or corroded contact can cause intermittent operation and localized overheating.
  • Careless removal: prying, pulling on cables and incorrect fitting can damage the connectors, clips and assembly housing.

Additional information

Weight 0.9 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.