Description
Heater actuator motor for CITROEN C4 and PEUGEOT 307 II
Part description
Used BEHR B5783 U and 43 heater actuator motor is an electric control component of the heating and air conditioning system. Actuator motors of this type reposition the flaps in the ventilation system in response to control settings. A faulty actuator may cause clicking, irregular flap movement, or no expected change when the heating settings are adjusted.
The designations EAD512, 6447RZ and 6447RF are important when searching for a replacement part. Before selecting a part, compare the designation on the original actuator motor, the connector, the mounting points and the actuator output design. A correctly selected used part can be a cost-effective repair solution if the fault is with the actuator motor itself, rather than a jammed flap or an electrical wiring fault.
Technical information
- Manufacturer: BEHR
- Model: Citroën C4 | Peugeot 307; the long description specifies Peugeot 307 II.
- Part type: electric heater actuator motor.
- Design designation: B5783 U and 43
- Other numbers: EAD512, 6447RZ, 6447RF
- Condition: used part.
- Specific flap operated and air conditioning configuration: not specified.
Product codes
- Product codes: 6447RZ, 6447RF, EAD512, B5783 U and 43
- Models listed on labels: Citroën C4 | Peugeot 307
Code 6447RZ is listed in the product name, while 6447RF appears in the short description. The available information does not confirm that they are interchangeable; therefore, when selecting a part, also refer to the designation and design of the original part.
Installation recommendations
The following procedure applies in general to this type of part. Exact access to the actuator motor, removal of surrounding parts, and any end-position adjustment depend on the specific model and heating or air conditioning configuration.
1) Before installation
- Compare the designations on both parts, the shape and number of connector pins, the mounting points and the shape of the actuator output.
- Inspect the used part: the housing and mounting tabs must not be cracked, the contacts must not be corroded, and the actuator output must not show visible damage.
- Check whether the problem is caused by the wiring, a loose connector or a mechanically jammed flap.
- Before disassembly, take photos of the wiring routing, mounting points and position of the original actuator.
2) Required tools and materials
- Screwdrivers or bits suitable for the fasteners used.
- Plastic trim removal tools, a flashlight and a container for fasteners.
- A clean cloth and, if needed, a product designed for cleaning electrical contacts.
- If necessary, suitable automotive diagnostic equipment to check operation and perform any initialization.
3) Step-by-step installation procedure
- Secure the vehicle against movement, switch off the ignition and follow the manufacturer’s instructions for safely disconnecting electrical components. If the battery must be disconnected, follow the prescribed procedure.
- Access the faulty actuator motor according to the service procedure. Carefully release the surrounding covers to avoid damaging their clips.
- Note the actuator’s position and how it connects to the flap mechanism.
- Release the connector lock and disconnect it by holding the connector body, not by pulling on the wires. Check the condition of the contacts and wiring.
- Release the actuator motor fasteners and carefully separate it from the mechanism it operates. Do not pry against the plastic mounting tabs.
- Check the connection to the flap and, according to the service procedure, verify that it moves freely. Do not force the mechanism past its end positions.
- Compare the removed part with the replacement part again. If the connector, mounting points or actuator output differ, do not proceed with installation.
- Fit the replacement actuator motor so that its output engages correctly with the flap mechanism. Align it according to the service instructions; do not force the gears to turn or use the screws to pull a misaligned part into place.
- Secure the actuator motor according to the manufacturer’s instructions, connect the connector and keep the wiring clear of moving parts and sharp edges.
- Restore the power supply using the prescribed procedure. If the configuration requires initialization or end-position adjustment, carry it out using the appropriate service procedure.
- Check operation before fully reinstalling the covers. Then refit the removed covers and trim.
4) Post-installation checks and operation verification
Gradually change the heating and air conditioning settings related to the actuator being repaired. Check that the system responds and that there is no repeated clicking or gear skipping. Check that the connector and wiring are secure. After reassembly, operation can also be checked during a short test drive; only operate the controls when it is safe to do so.
5) Common installation errors and how to avoid them
- Selecting a part based only on the vehicle model: also compare the designation, connector and mechanical design of the actuator.
- Replacing the actuator without checking the flap: first resolve any sticking, otherwise the replacement actuator motor may be overloaded again.
- Forcing the actuator into place or turning the output coupling too far: align it according to the service procedure rather than applying pressure to the part.
- Overtightening fasteners: follow the manufacturer’s instructions and protect the plastic mounting tabs from cracking.
- Skipping the required initialization: check whether the specific system configuration requires it and perform it if necessary.
Reasons for part failure
The following are general causes of failure that may affect heater actuator motors; they do not describe the known condition of this particular unit:
- Gear wear from repeatedly repositioning the flaps.
- A sticking or jammed flap, which places excessive load on the actuator and its gears.
- Wear of the electric motor or position sensor, if included in the specific configuration.
- Moisture and contact corrosion, which can disrupt the electrical connection.
- Damage during careless removal or installation, especially cracked mounting tabs or damage to the actuator output.







