Citroën Peugeot 96773911XT 6242WQ Lever Controls

Description

Controls under the steering wheel, COM2008 multifunctional control block for PEUGEOT 3008 and 5008
They control the lights, fog lights, car radio, cruise control and car radio (need to deliver or hand over the controller), front wipers, wiper sensor, ESP, car radio

Part description

This used COM2008 steering wheel control block is intended for Citroën Peugeot / Stellantis cars and is primarily searched for by original part numbers. It is an important electrical component that combines several functions into one unit and ensures convenient control of selected systems directly from the driver’s seat.

The advantage is the multifunctional design, where one unit serves several commonly used functions. When replacing, it is essential to compare not only connectors and part numbers, but also the actual equipment of the original car and the presence of individual controls. Controls for lights, fog lights, car radio, cruise control, front wipers, wiper sensor and ESP are explicitly stated for this piece.

• Part Type: Lever Controls / Steering Wheel Controls
• Implementation: COM2008 multifunctional block
• Category: electrical components
• Determination according to the documents: Peugeot 3008 I, Peugeot 5008 I

Technical information

• Manufacturer: Stellantis Citroën Peugeot
• Model: Peugeot 3008 I, Peugeot 5008 I
• Other numbers: 6242WQ, 6243A0, 96773911ZD

Product codes

• Product codes: 96773911XT, 6242WQ, 6243A0, 96773911ZD
• Model names: PEUGEOT 3008 I, PEUGEOT 5008 I

Installation recommendations

This part is an electric multifunction controller under the steering wheel. Exact replacement steps may vary by vehicle and trim, so below is a general and typical procedure for this type of part.

1) Before assembly

• Check that the product numbers and markings on the original and new part match.
• Compare the shape of the body, the attachment, the number and type of connectors and the design of the levers.
• Verify the presence of the required functions, for example control of lights, wipers, cruise control, radio or other elements listed in the documents.
• If a separate car radio controller needs to be transferred, prepare the original functional piece.
• Inspect the used part for damaged plastic, latches, connectors or levers.

2) Necessary tools and materials

• regular set of hand tools
• screwdrivers and bits corresponding to the connections used
• plastic pry bar for removing interior covers
• clean cloth
• preparation for cleaning electrical contacts, if suitable
• protective gloves

3) Step-by-step assembly procedure

1. Park the vehicle in a safe place and turn off the ignition.
2. Disconnect the battery and wait a reasonable amount of time according to normal service practice to minimize the risk of damage to electrical components.
3. Remove the covers around the steering column to gain access to the control block.
4. Carefully disconnect the electrical connectors from the old part. Do not pull on the wiring, but only on the connectors and their securing.
5. Release the original controller block from the mounting according to the design of the specific car.
6. Compare the old and new part side by side, including all mounts, connectors and controls.
7. If it is necessary for your design, transfer the car radio controller from the original part to the new part.
8. Sit the new controller block into the correct position without using excessive force.
9. Connect all connectors and check that they are properly secured.
10. Reinstall all the removed interior covers.
11. Connect the battery.
12. Turn on the ignition and test the individual functions of the controller one by one.

• 4) Post-assembly checks and function verification

  • Check the correct operation of the lights and fog lights.
  • Test the front wipers and possibly the wiper sensor function if the car is equipped with this equipment.
  • Verify the cruise control and radio controls if the model uses them.
  • Check that the levers move smoothly, without excessive play or stuttering.
  • During a short test drive, observe whether there are any unusual manifestations in the control of the relevant functions.

  5) The most common assembly mistakes + how to avoid them

  • Swapping a similar part: always compare all numbers and equipment, not just looks.
  • Damage to the connector: disconnect the connectors carefully and respect their securing.
  • Insufficient seating of the part: after assembly, check for proper seating and attachment.
  • Omission to transfer the car radio controller: if it is stated that the controller must be delivered or transferred, take this into account before the installation itself.
  • Assembly without checking functions: after connection, always test all controlled circuits, not just one function.

  Reasons why the part is damaged

  • Normal wear and tear from long-term use of levers and switches.
  • Mechanical stress caused by frequent operation or careless handling.
  • Damage to contacts due to age, oxidation or pollution.
  • Cracking of plastic parts during disassembly or under higher load.
  • Fault of the internal mechanism, which may result in the failure of some of the functions.