Central Locking Controller Citroën Peugeot 9817042977 98170429ZD

€15.00

Stellantis Citroën Peugeot
9817042977 98170429ZD

1 in stock

Description

Central locking controller for CITROËN, PEUGEOT and other Stellantis models

This central locking controller is designed for a range of Stellantis small vans and MPVs and is commonly referenced by part numbers 9817042977 and 98170429ZD. Intended for professional garages and experienced DIY mechanics, the unit controls door locking/unlocking commands, remote receiver input and related central locking relays. It is a direct-fit electrical component for vehicles in the Berlingo/Rifter/Combo/Doblo/ProAce City family and is frequently searched by its product codes, so keep those numbers handy when ordering or checking compatibility.

Function And Benefits

The controller manages the central locking system: interpreting key fob signals, operating lock actuators and communicating lock status to the vehicle network. Replacing a faulty controller restores reliable locking, remote entry and often eliminates intermittent door lock behaviour. Benefits include quick restoration of vehicle security, elimination of draining electrical faults caused by failing relays and improved convenience for fleet or daily-use vehicles.

Compatibility And Models

Known Fitment: Citroën Berlingo (K9), Peugeot Rifter, Fiat Doblo III, Opel Combo E (K9), Toyota ProAce City. Always reference the product codes below when searching or ordering.

How The Part Is Replaced

  • Disconnect Battery: Always isolate the battery before starting to avoid short circuits and potential damage to electronic modules.
  • Access Unit: Remove trim panels in the dashboard or under-dash area or behind the glovebox/fusebox depending on vehicle model to reach the controller.
  • Disconnect Connectors: Carefully unplug multi-pin connectors and release any securing clips or brackets.
  • Remove And Fit: Unscrew the mounting screws, fit the replacement unit in the same orientation and reattach connectors and fasteners.
  • Coding/Configuration: The unit may require cloning of original data or coding to the vehicle to restore full functionality (see Important Note On Installation And Coding below).
  • Test Operation: Reconnect the battery and verify locking/unlocking from remote and door switches, check for fault codes and confirm no parasitic drain.

Installation Recommendations

  • Use suitable trim tools to avoid damage to panels and connectors.
  • Ensure connector pins are clean and free of corrosion; apply contact cleaner if necessary before reconnection.
  • Verify good ground and power supply at the module before and after installation to prevent repeated failures.
  • Perform a full function check including all doors, boot/tailgate and remote fob functions.

Installation And Coding – Important

– The Unit Is Used And Is “Paired” With The Original Vehicle (VIN/PIN/Keys).

– Options For Commissioning:

  1. Cloning Data From The Old Unit (EEPROM/Flash) – After Cloning The Unit Is Plug And Play.
  2. Virginization And Subsequent Initialization/Telecoding Via DiagBox (Or Online) + Key Adaptation.

– Recommended To Be Performed By A Specialist With PSA Service Equipment (DiagBox/Lexia/PP2000).

– Before Removal/Installation Always Disconnect The Battery And Follow The Manufacturer Procedure To Avoid Damage To The Unit.

Most Common Failure Causes

Central locking controllers typically fail due to water ingress and corrosion at connectors, damaged wiring or chafed loom sections, failed internal relays or electronic components from voltage spikes, or thermal stress from prolonged use. Intermittent faults often arise from poor grounding or loose connectors rather than the controller itself, so inspect wiring and grounds when diagnosing.

Technical Information

Notes For Buyers

Search By Part Number: This part is commonly identified and ordered using codes 9817042977 or 98170429ZD. For fitment, match the product codes to the vehicle parts list for the specific model/production year. Suitable for professional repair shops and experienced DIYers comfortable with vehicle electronics and coding procedures.

Why Choose This Part

Replacing a malfunctioning central locking controller with a correct-code unit restores reliable remote access and reduces electrical faults. For fleet vehicles and high-use models, a properly fitted and coded controller improves vehicle security and decreases service call frequency.

Additional information

Weight 0.5 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.