Description
Multifunction video screen for Stellantis vehicles
Some functions may need to be initialized using diagnostic equipment
Part description
The used radio and onboard computer display 98162661ZD is a multifunction screen for the Citroën, Peugeot and Opel vehicles listed below. It displays information from the relevant onboard system; the specific range of functions depends on the vehicle’s equipment and configuration.
If you are experiencing an unreadable image, display outages or damage to the existing screen, replacing the display may be a suitable solution once the cause of the fault has been confirmed. When selecting a replacement, compare the product numbers, connectors and configuration of the original part. Some functions may need to be initialized using diagnostic equipment after installation.
Technical information
- Manufacturer: Stellantis – according to the supplied documentation.
- Model: Citroën Berlingo K9 | OPEL COMBO E K9 | PEUGEOT PARTNER III | PEUGEOT RIFTER.
- Part type: multifunction video screen / radio and onboard computer display.
- Condition: used car part.
- Main product number: 98162661ZD.
- Other numbers: 9828422080, 9830426480.
- Commissioning: some functions may require initialization using diagnostic equipment.
Product codes
- Product codes: 98162661ZD, 9828422080, 9830426480.
The numbers are listed in the documentation for this product. Matching the vehicle model alone does not guarantee that all display variants are compatible; the configuration and compatibility with the onboard electronics are also important.
Installation recommendations
General information for this type of part: the following procedure is a general guide to replacing a vehicle display. The exact trim removal procedure, mounting method and any initialization depend on the specific vehicle model and equipment. Follow the manufacturer’s service procedure.
1) Before installation
- Compare the markings on the original and replacement parts, the shape of the housing, mounting points, and the number and type of connectors.
- Inspect the screen, housing, mounts and contacts. Check for cracks, bends, corrosion or signs of moisture exposure.
- First rule out a fault in the power supply, wiring or connected system. The display itself may not be causing the display failure.
- If possible, record the original settings and symptoms of the fault for later comparison.
2) Required tools and materials
- Plastic tools for careful trim removal.
- Hand tools suitable for the fasteners used.
- A soft, clean work surface, a screen-cleaning cloth and protection for surrounding surfaces.
- Suitable diagnostic equipment for checking the system and, if necessary, initializing functions.
3) Step-by-step installation procedure
- Park the vehicle safely, switch off the ignition and turn off electrical accessories.
- Allow the electronics to enter sleep mode and disconnect the battery according to the vehicle manufacturer’s procedure.
- Cover surrounding surfaces to prevent scratching them during the work.
- Following the service procedure, release the trim needed to access the display. Do not use excessive force to overcome resistance from the clips.
- Release the original display’s fasteners and carefully slide it out far enough to avoid putting tension on the wiring.
- Note the cable routing, release the connector locks and disconnect them by holding their bodies, not the wires.
- Check the condition of the connectors and wiring. Resolve any damage before connecting the replacement part.
- Connect the compatible connectors to the replacement display and check that their locking tabs are properly secured.
- Position and secure the display without putting it under tension. Cables must not be pinched or routed over sharp edges. Refit the trim according to the service procedure.
- Restore the power supply according to the manufacturer’s instructions, check operation and perform diagnostic initialization if needed.
4) Post-installation checks and function verification
With the vehicle stationary, check that the image is clear and stable, that the available controls respond, and that functions corresponding to the vehicle’s equipment are displayed. Also check the system’s behavior after switching it off and back on. If any functions are missing, check the connections and whether initialization using diagnostic equipment is required. If carrying out a test drive, monitor only normal system operation; do not perform diagnostics or adjustments while driving.
5) Common installation mistakes and how to avoid them
- Choosing based only on the vehicle name: also compare the part numbers and physical configuration.
- Disconnecting while powered: follow the prescribed procedure for shutting down the electronics and disconnecting the battery.
- Damaging connectors or clips: release the locks first and use suitable tools.
- Applying pressure to the display surface: handle the part by its housing and place it on a soft surface.
- Skipping initialization: limited functionality after replacement does not necessarily mean the display is faulty; some functions may require diagnostic configuration.
Reasons why the part may become damaged
Common possible causes of damage to vehicle displays include:
- Mechanical impact or excessive pressure on the screen and its housing.
- Moisture and cleaning products entering the unit, which can damage the electronics or contacts.
- Prolonged temperature stress and component aging, which may result in reduced readability or image outages, for example.
- Power supply faults and electrical surges, which can affect electronic circuits.
- Improper removal, which can break mounts, damage connectors or put stress on the wiring.
These causes are general and do not describe the condition of the item offered. Before replacing the display, it is important to eliminate any external cause of the fault as well, to prevent it from damaging the replacement display.
