Description
Engine Control Unit Bosch ME7.4.5 for Citroën C4 1.6 16V.
This Bosch ME7.4.5 ECU is a direct-fit engine management unit used on Citroën C4 1.6 16V applications. Designed for professional workshops and experienced DIY mechanics, the unit maintains precise control of fuel injection and ignition to ensure smooth running, good drivability and emission control. The description below highlights compatibility codes, technical details and practical guidance for safe replacement and commissioning.
Technical Information
- Manufacturer: Bosch
- Model: ME7.4.5
- Product Codes: 0261208491
- Additional Numbers: 9657489380, 9652552380, 1940SV, 261208491, NFP
Function And Operation
The ECU controls fuel injection timing and duration, ignition timing, lambda (oxygen sensor) feedback loops and rev-limiter functions. It monitors numerous engine sensors (air mass, coolant temperature, throttle position, crank/cam sensors) and executes real-time corrections to optimize performance and emissions. It also communicates diagnostic trouble codes (DTCs) via the vehicle network for workshop diagnostics.
Recommended Applications
Primarily fitted to Citroën C4 1.6 16V models equipped with the Bosch ME7.4.5 management system. The same Bosch part numbers may appear on several PSA/ Stellantis vehicles that share the EP6 engine family—always check the ECU product codes stamped on the unit to confirm fitment.
Common Failure Modes And Causes
- Water Ingress Or Corrosion: Moisture entering the connector or housing causes shorts or corrosion on pins.
- Heat And Thermal Cycling: Repeated heating/cooling can damage solder joints or electronic components.
- Electrical Surges / Poor Battery Connections: Voltage spikes or jump-start errors may damage internal circuits.
- Connector Damage Or Bent Pins: Poor contact leads to intermittent faults or sensor signal loss.
- Software/Data Corruption: EEPROM/Flash errors or immobiliser pairing mismatches can prevent engine start or proper operation.
How To Replace
Replacement should follow a workshop-standard sequence: safely isolate the vehicle electrics, remove protective trims, unclip the ECU connectors and remove mounting fasteners. Fit the replacement unit in the reverse order, ensuring connectors are fully seated and locking tabs engaged. After mechanical installation, commissioning or coding may be required before the engine runs normally.
Installation Recommendations
- Always disconnect the negative battery terminal before starting work to avoid short circuits and protect the ECU electronics.
- Work in a clean, dry environment and use dielectric grease on connector pins if appropriate to prevent corrosion.
- Handle the unit carefully to avoid ESD damage—avoid touching exposed pins and circuit boards.
- Secure all mounting bolts and routing for wiring harnesses; avoid sharp edges or contact that can chafe insulation.
Installation And Coding – Important
- The Unit Is Used And Is “Paired” With The Original Vehicle (VIN/PIN/Keys).
- Options For Commissioning:
- Cloning Data From The Old Unit (EEPROM/Flash) – After Cloning The Unit Is Plug And Play.
- Virginisation And Subsequent Initialization/Telecoding Via DiagBox (Or Online) + Key Adaptation.
- Recommended To Be Performed By A Specialist With PSA Service Equipment (DiagBox/Lexia/PP2000).
- Before Removal/Installation Always Disconnect The Battery And Follow The Manufacturer Procedure To Avoid Damage To The Unit.
Why Choose This Unit
This Bosch ME7.4.5 ECU provides OEM-level control logic for the Citroën C4 1.6 16V platform and carries the common Bosch and PSA part references used in service replacements. For workshops it offers a reliable solution when replacing a failed management unit, provided correct commissioning and any necessary cloning or coding are performed.
Notes For The Mechanic
Before fitting, confirm that the part numbers on the unit match the numbers required for the vehicle. If cloning, ensure a complete and verified EEPROM/Flash image is copied. If performing virginisation and coding, make sure immobiliser and key adaptation steps are included in the commissioning procedure to restore full functionality.







