Heater Servo Motor BEHR B5783 U and 43 Citroën Peugeot EAD512 6447RZ

€42.00

Stellantis Citroën Peugeot
6447RF EAD512 B5783 U and 43

2 in stock

Description

Heater servo motor for Citroën C4 and Peugeot 307 II vehicles.

Product Overview

This heater servo motor (blend door actuator) controls airflow direction and temperature mixing inside the HVAC box of Citroën C4 and Peugeot 307 II models. Designed as a direct-fit replacement for worn or failed actuators, this unit restores precise climate control operation, eliminating issues such as incorrect cabin temperature, restricted airflow, or clicking noises from the dashboard. Common search keywords: heater servo motor, blend door actuator, Citroën C4 heater motor, Peugeot 307 heater actuator, EAD512, 6447RZ, B5783.

Compatibility

Fits the following models (as commonly referenced by mechanics and DIY enthusiasts): Citroën C4; Peugeot 307 II. Often searched and ordered by part numbers rather than full model name—check the product codes listed below.

Technical Information

  • Manufacturer: BEHR
  • Model: Citroën C4, Peugeot 307 II
  • Product Codes: 6447RF, 6447RZ
  • Additional Numbers: EAD512, B5783, B5783 U a 43

Function And Common Faults

The servo motor positions internal flaps (blend doors) that mix hot and cold air and route airflow to vents, footwell or windshield. Over time plastic gears inside the actuator can wear or strip, the small DC motor may fail, or electrical connectors and potentiometers can degrade. Symptoms of failure include audible clicking, inability to change temperature or vent mode, inconsistent cabin temperature, or permanent operation in one vent position.

Why This Part Fails Most Often

  • Worn Or Stripped Plastic Gears: Repeated movement causes gear tooth wear or breakage.
  • Motor Wear Or Burnout: Small DC motors can fail after many hours of operation or when blocked.
  • Moisture And Contamination: Water ingress or debris in the HVAC box can jam the mechanism.
  • Mechanical Load From Blocked Flaps: Stiff or frozen blend doors increase load and accelerate failure.

Installation Recommendations

Replacement can usually be performed by a trained mechanic or an experienced DIYer with basic tools. Typical procedure: locate and access the HVAC actuator behind the dashboard on the passenger side (specific access panels and steps vary by model), disconnect the electrical connector, remove retaining screws, extract the old actuator and transfer any mounting brackets or linkage, fit the new unit ensuring correct gear engagement, secure fasteners and reconnect the connector. After installation, run the HVAC through all modes to confirm correct movement and response. As a general safety precaution, isolate the vehicle electrical supply before working on electronics to avoid short circuits—follow vehicle manufacturer guidance and standard workshop procedures.

Signs You Need Replacement

  • Clicking or grinding noise from the dash when changing vents or temperature.
  • No change in temperature despite control inputs.
  • Airflow stuck to one vent position (defrost/face/footwell) regardless of settings.
  • Intermittent operation or slow flap movement.

Notes For Mechanics And DIYers

This part is commonly identified and ordered by its product codes (6447RF / 6447RZ / EAD512 / B5783). When replacing, verify physical match with the removed unit: connector type, mounting points and gear orientation. If the actuator fails shortly after replacement, inspect the HVAC flaps and linkage for binding or foreign objects that could overload the new servo.

Warranty And Quality

Units should fit as direct replacements when matched by part number. Use correct installation practices and verify free movement of HVAC flaps before final assembly to ensure durability and proper function.

Additional information

Weight 0.4 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.