Description
Door Handle For Right Front And Rear Doors For Both Right And Left Sides For CITROËN C4 II B7, C‑Elysée, DS4, Peugeot 301. Color FXT – CORNELIE BLACK
Replacement exterior door handle designed for Citroën and Peugeot models. This painted FXT Cornelie Black handle fits the right front and rear doors and is a direct-fit part for vehicles specified below. Intended For Use By Professional Technicians And Experienced DIY Enthusiasts; Often Searched By Product Codes 9101LY And 96868965XT.
Key Features
- Exterior Door Handle For Right Front And Rear Doors
- Painted Finish: FXT Cornelie Black — color-matched To Exterior
- Direct Fit For Specified Citroën And Peugeot Models
- Durable Construction With Internal Metal Components And Painted Plastic Cover
- Commonly Referenced By OE Codes 9101LY And 96868965XT
Technical Information
- Manufacturer: Stellantis (Citroën / Peugeot)
- Model: Citroën C4 II (B7), C‑Elysée, DS4, Peugeot 301
- Product Codes: 9101LY; 96868965XT
- Additional Numbers: 9101LY | 96868965XT
Function And Application
This part is an exterior door handle that operates the mechanical latch and connects to the door lock/linkage. It provides the user interface to open the door from the outside and transmits movement to the latch assembly via rods or cables. Suitable For Right Side Front And Rear Doors On The Listed Models.
How To Replace
- Prepare Tools: Trim Removal Tool, Philips And Flat Screwdrivers, Socket Set, Torx Bits, Pliers.
- Remove Interior Door Trim Panel Carefully To Access The Handle Fixings; Start With Trim Clips, Then Remove Screws And Lift Panel Off.
- Peel Back The Vapor/Water Shield To Reach The Handle Area.
- Disconnect The Linkage Rods Or Cables From The Handle (Note Their Orientation For Reassembly) And Unclip Any Electrical Connectors For Central Locking If Present.
- Unscrew The Retaining Bolts Or Nuts Holding The Handle From The Inside Of The Door, Then Remove The Old Handle From The Outside.
- Install The New Handle: Position From Outside, Tighten Fasteners From Inside, Reconnect Linkages And Electrical Connectors, Ensuring Secure Clips And Correct Alignment.
- Test Operation Of Mechanical Latch And Central Locking Before Reassembling The Door Trim. Ensure Smooth Movement And No Binding.
- Reinstall Water Shield And Door Trim, Verify All Clips And Screws Are Secured.
Installation Recommendations
- Check And Replace Any Broken Plastic Clips Or Retaining Fasteners During Installation.
- Apply A Light Lubricant To Moving Metal Parts And Pivot Points To Reduce Wear.
- Align Handle Carefully To Avoid Excessive Stress On Linkage Rods.
- If The Door Has Electric Components (Central Locking, Sensors), Disconnect The Battery Before Working On Electrical Connectors.
- Use Proper Trim Tools To Avoid Damaging Interior Panels And Clips.
- Verify Paint Match Before Final Installation; Minor Touch-Up Can Be Done By A Bodyshop If Needed.
Why The Part Most Often Fails
- Mechanical Wear: Repeated Use Causes Plastic Lugs, Clips Or Internal Mechanisms To Wear Or Break.
- Impact Damage: Door Handle Breakage From Accidents Or Strong Impacts.
- Plastic Brittleness And UV Degradation: Prolonged Sun Exposure Can Make Painted Plastic Brittle, Leading To Cracks.
- Corrosion Of Internal Metal Components Or Fasteners, Especially In Areas With Road Salt.
- Faulty Or Misaligned Linkage Rods And Worn Door Latch Increasing Load On The Handle.
Compatible With Models Listed Above When Fitted According To Manufacturer Guidelines. Use The Product Codes 9101LY Or 96868965XT When Searching For This Exact Replacement Handle.
