Description
Set Of 2 Keys And Locks For CITROËN BERLINGO II And PEUGEOT PARTNER II. Includes Ignition Barrel, 2x Front Door Lock, Rear Right Sliding Door Lock, Fuel Flap Lock. All Locks Are Functional.
Product Overview
Complete lock-and-key set designed for Citroën Berlingo II and Peugeot Partner II. The kit contains an ignition barrel, two front door locks, rear right sliding door lock and a fuel flap lock. Supplied locks are functional and intended as a direct replacement for worn or damaged original units. Ideal for professional workshops and experienced DIY mechanics looking for a full door-and-ignition replacement solution.
Technical Information
- Manufacturer: Stellantis (Citroën / Peugeot)
- Model: Citroën Berlingo II, Peugeot Partner II
- Product Codes: 4162CF, 4162CH
- Additional Numbers: Not Available
Fitment
Fits Citroën Berlingo II and Peugeot Partner II series. Confirm correct side and position (front door, sliding rear door, fuel flap) before installation. The set is intended to replace the original mechanical locks and ignition barrel with identical-function parts.
How The Part Works
Door Locks And Ignition Barrel: Mechanical locking components operate the latch mechanisms and enable key operation of the vehicle’s ignition and doors. The fuel flap lock secures the fuel filler cap. When keys turn in the ignition barrel they mechanically rotate the tumblers to start the engine (immobiliser chip may be present in some keys). Door locks activate latches and, where applicable, work together with central locking actuators to lock/unlock all doors.
Installation Recommendations
- Safety First: Disconnect The Battery Before Starting Any Work To Prevent Short Circuits And Avoid Triggering Electrical Systems.
- Door Lock Replacement: Remove Interior Door Trim To Access Lock Mechanism. Detach Linkages And Electrical Connectors (If Present), Unscrew Mounting Bolts, Replace Lock Unit And Reassemble Linkages Ensuring Proper Adjustment Of Rods And Cables.
- Ignition Barrel Replacement: Remove Steering Column Covers To Access The Barrel. Release Retaining Clip Or Bolts, Withdraw Old Barrel And Fit New Unit. Check Steering Lock Engagement And Key Operation Before Reassembly.
- Fuel Flap Lock: Access From Inside Rear Quarter Panel Or Through Wheel Arch Liner Depending On Body Style. Remove Retaining Screws, Replace Lock, And Verify Proper Closure.
- Electrical Connections: Where Central Locking Actuators Or Electrical Switches Are Attached, Inspect Wiring And Connectors For Corrosion Or Damage And Replace If Necessary.
- Keying And Immobiliser: If Keys Contain Transponder Chips, Immobiliser Programming May Be Required To Start The Vehicle. Programming Typically Requires Dealer Or Specialist Equipment.
- Recommended Tools: Torx/Screwdriver Set, Trim Tools, Pliers, Socket Set, Multimeter For Electrical Checks.
- Testing: After Installation, Verify Smooth Mechanical Operation Of Each Lock, Confirm Central Locking Function (If Applicable) And Ensure Ignition Turns Smoothly Without Excessive Play.
Why These Parts Fail
- Mechanical Wear: Frequent Use Causes Worn Tumblers, Broken Springs Or Worn Keyways Leading To Difficult Operation Or Failure.
- Corrosion And Water Ingress: Moisture Penetration Can Corrode Internal Components And Electrical Contacts, Especially On Lower Door Locks And Fuel Flap Locks.
- Physical Damage: Forced Entry, Impact, Or Bent Keys Can Damage Lock Mechanisms Or Break Key Blades.
- Actuator Or Linkage Failure: Door Lock Problems May Be Caused By Failed Central Locking Actuators Or Detached/Adjusted Linkages, Not Only By The Lock Cylinder Itself.
- Age And Dirt Buildup: Accumulated Dirt, Lack Of Lubrication Or Deteriorated Seals Reduce Reliability Over Years Of Service.
Practical Tips For Mechanics
- When Replacing A Single Lock, Inspect Adjacent Locks And Actuators To Avoid Repeating The Job Shortly After.
- Lubricate Moving Parts With Appropriate Lock Grease After Installation To Extend Service Life.
- If Keys Show Excessive Wear, Have New Blanks Cut From A Good Original Or Replace All Locks And Keys To Ensure Consistent Operation.
- Document Key Codes And Keep A Spare Key Stored Safely To Reduce Vehicle Downtime.
Summary
This lock and key set offers a practical, workshop-oriented solution for restoring door, ignition and fuel flap security on Citroën Berlingo II and Peugeot Partner II vehicles. Includes essential mechanical components for immediate replacement; suitable for professional fitment or experienced DIYers comfortable with door trim removal and ignition barrel replacement.
