Description
Combined Instrument Cluster For Citroën C4 B7. The Vehicle Had Approximately 110000 Km ± 3,000 Km.
Product Overview
High-quality replacement instrument cluster (tachometer / gauge cluster) suitable for Citroën C4 II (B7) vehicles. This unit displays speed, engine RPM, fuel level, coolant temperature and on-board warnings and includes the odometer reading. Commonly searched under part numbers 96657316XT, 9812831980, 6103QC and 6103QE — include these codes when searching or ordering to ensure quicker match.
Key Benefits
- Direct Fit For Citroën C4 II (B7) Dashboards — Designed To Match OEM Mounting Points And Connectors.
- Keeps Full Functionality Of Speedometer, Tachometer, Fuel And Temperature Gauges.
- Ideal For Mechanics And DIY Enthusiasts Looking For A Reliable Unit With Known Product Codes.
- Instrument Cluster Supplied From Vehicle With Approximately 110,000 Km — Useful For Mileage Reference And Diagnostics.
Compatibility
Intended For: Citroën C4 II (B7) models. When searching, use product codes 96657316XT / 9812831980 / 6103QC / 6103QE or the label values 6103QC/6103QE to locate matching units. Compatible With Stellantis-Citroën/Peugeot Electrical Systems Typical For C4 II Dash Harnesses.
Technical Information
- Manufacturer: Stellantis (Citroën/Peugeot)
- Model: Citroën C4 II (B7)
- Product Codes: 96657316XT, 9812831980
- Additional Numbers: 6103QC, 6103QE
- Recorded Mileage: Approx. 110000 Km ± 3,000 Km
How To Replace (General Guide)
Replacement of the instrument cluster is a straightforward procedure for a qualified mechanic or a competent DIYer with basic tools. Typical steps:
- Disconnect The Battery Before Starting To Prevent Short Circuits Or Damage To Electronic Modules.
- Remove Trim Panels Around The Steering Column And Dash To Access The Cluster (May Require Removing Steering Column Shrouds).
- Unscrew The Cluster Fasteners (Usually 2–4 Screws) And Carefully Pull The Cluster Forward.
- Unplug The Multiway Connectors And Any Illumination Bulb Sockets.
- Fit The Replacement Unit, Reconnect Connectors, Refit Screws And Trim, Then Reconnect The Battery.
- After Installation, Check All Gauges, Indicator Lights And Warning Messages For Correct Operation.
Installation Recommendations
- Always Disconnect The Battery Prior To Removal/Installation To Avoid Damage To The Cluster Electronics.
- Handle Connectors And PCB Areas Carefully — Avoid Pulling On Wiring Only; Release Connector Locks First.
- Inspect Wiring And Connectors For Corrosion Or Damage While The Cluster Is Out; Repair Any Faults To Prevent Recurrence.
- If The New Cluster Shows Incorrect Mileage Or Immobiliser Messages, Professional Reprogramming Or Data Cloning May Be Required.
- Where Coding Is Necessary, Use Appropriate Diagnostic Equipment And Follow Manufacturer Procedures.
Most Common Failure Reasons
- Electronic Faults On The Cluster PCB Caused By Thermal Cycling Or Ageing Components.
- Stepper Motor Or Gauge Actuator Wear Leading To Erratic Or Stuck Needles.
- Poor Solder Joints Cracking Over Time Causing Intermittent Failures.
- Water Ingress Or Dampness From Leaks Causing Corrosion And Short Circuits.
- Connector Corrosion Or Broken Wiring In The Dash Harness.
Notes
This unit Was Removed From A Vehicle And Has The Mileage Shown Above. Product Codes And Additional Numbers Are Included To Help With Fast Identification. Suitable For Auto Mechanics And Experienced DIYers Who Need A Direct-Fit Instrument Cluster For Citroën C4 II (B7).
