Description
BSI Siemens E01-00 for Citroën Xsara Picasso, Berlingo and Peugeot 206, Partner.
This used BSI (Body System Interface) Siemens E01-00 is suitable for a range of Citroën and Peugeot models and is often searched by part numbers such as 9657999680, S118085320 or 1650882480. The unit manages multiple comfort and body functions and is a common replacement item for workshops and DIY mechanics maintaining Xsara Picasso, Berlingo, 206 and Partner vehicles. If you are troubleshooting intermittent electrics, central locking faults, or communication errors on the CAN bus, this BSI unit is a direct-replacement option for compatible vehicles and specified part codes listed below.
Technical Information
- Manufacturer: Siemens
- Model: BSI E01-00
- Product Codes: 9657999680, S118085320, E01-00
- Other Numbers: 1650882480, 1650882680, 650883080, 6580T5, 6580EZ, 6580EY, 6580GY
Function And Fitment
The BSI is the central comfort and body control unit that coordinates lighting, wipers, central locking, interior electronics, switch inputs and acts as a gateway on the vehicle CAN network. A malfunctioning BSI can produce a wide range of symptoms: failure of central locking, intermittent lights, non-working wipers, dashboard warning messages, or loss of certain communication lines between modules. This specific Siemens E01-00 variant is referenced for Citroën Xsara Picasso and Berlingo, and for Peugeot 206 and Partner in compatible configurations.
Replacement Procedure
Typical replacement steps for a competent mechanic or experienced DIYer:
- Disconnect the negative battery terminal before any work to avoid electrical damage.
- Access the BSI unit, normally located under the dashboard on the passenger side (behind the glovebox or lower trim) on the listed models.
- Remove surrounding trim and any retaining screws to free the unit.
- Carefully unplug all multi-pin connectors; note their positions and locking tabs.
- Install the replacement BSI, secure mounting screws and refit connectors ensuring full engagement.
- Proceed with the required coding or data transfer steps (see Installation and Coding – Important below) before reconnecting all systems and the battery.
Installation Recommendation
- Perform mounting and electrical work in a dry, well-lit area and use proper anti-static precautions.
- Verify connector pins and wiring harness condition before installation; corroded pins should be cleaned or replaced.
- After installation, check all controlled functions (lights, wipers, locks, dashboard messages) and perform a road test to confirm correct operation.
Installation and Coding – Important
– The Unit Is Used And Is “Paired” With The Original Vehicle (VIN/PIN/Keys).
– Options To Bring The Unit Into Service:
- Kloning Data From The Old Unit (EEPROM/Flash) – After Cloning The Unit Is Plug And Play.
- Virginization And Subsequent Initialization/Telecoding Via DiagBox (Or Online) + Key Adaptation.
– Recommended To Be Performed By A Technician With PSA Service Equipment (DiagBox/Lexia/PP2000).
– Always Disconnect The Battery Before Removal/Installation And Follow Manufacturer Procedures To Avoid Damaging The Unit.
Why This Part Fails Most Often
- Water Ingress And Humidity: Moisture entering the passenger footwell or dashboard area causes corrosion and short-circuits on the PCB or connectors.
- Electrical Surges Or Poor Grounding: Voltage spikes, jump-starting errors or bad grounds can damage internal components.
- Thermal Stress And Solder Joint Fatigue: Repeated heating and cooling cycles may cause cracked solder joints or component failures.
- Connector Corrosion And Wiring Damage: Corroded pins or damaged harnesses lead to intermittent faults and communication errors.
Symptoms To Watch For: Intermittent or permanent failure of central locking, erratic lighting, non-working wipers, dashboard communication errors, or immobilizer-related starting faults when coding/pairing is lost.
Order this Siemens BSI E01-00 if the listed part numbers match your vehicle’s unit and you require a replacement BSI for Citroën Xsara Picasso, Citroën Berlingo, Peugeot 206 or Peugeot Partner. Installation and proper coding/cloning are critical for full restoration of functionality.
