Left mirror EZWD Citroën Xsara Picasso 8154JP

Description

Left rear view mirror CITROEN Xsara Picasso electrically operated
EZW color – FER GRAY LACQUER
Driver’s side
7 wires

Part description

Used left side mirror for Citroën Xsara Picasso is a suitable choice for repairing a damaged or non-functioning original part. This is a complete exterior rearview mirror on the driver’s side with electric control and connection via 7 wires.

The part is especially interesting for car mechanics and home repairers who are looking for an original used car part according to the exact designation. Another advantage is the EZW – FER gray paint color design, which can help with replacement without the need for additional body modifications.

Technical information

• Manufacturer: Citroën / Peugeot (Stellantis)
• Model: Citroën Xsara Picasso
• Other numbers: EZWD, NFP

Product codes

• Product codes: 8154JP, EZWD, NFP
• Models: Citroën Xsara Picasso

Installation recommendations

Generally/typically for the replacement of an exterior electrically operated rearview mirror, the exact procedure may vary according to the specific design of the car. Before installation, it is important to compare the new and original part, especially the number of wires, the shape of the connector, the attachment and the side of installation.

1) Before assembly

• Check if it is the left mirror on the driver’s side.
• Compare the 7-wire wiring with the old piece.
• Verify the fit, connector, cover shape and overall design match.
• Inspect the condition of the glass, cover, mirror joint and electrical supply.
• If you are replacing a damaged part, also check the surrounding parts of the door and the cable passage.

2) Necessary tools and materials

• A common set of hand tools
• Tool for removing internal plastic linings
• Screwdrivers and socket wrenches corresponding to the used connecting material
• Contact cleaner and clean cloth
• Protective gloves

3) Step-by-step assembly procedure

1. Turn off the ignition and secure the vehicle against movement.
2. Typically, the inner cover or part of the door trim at the point of access to the mirror attachment is removed first.
3. Carefully disconnect the electrical connector of the original mirror.
4. Undo the fasteners of the old mirror and safely remove the part.
5. Check the landing surface for dirt, deformation or damage.
6. Attach the used mirror and compare the position, fit and wiring before final mounting.
7. Plug in the electrical connector so that it is properly seated and without tension in the cable.
8. Place the mirror in place and evenly secure it with the original or matching fasteners.
9. Check that the wiring is not pinched between the mirror and the body.
10. Reinstall all removed covers and trim.
11. After mechanical fixing, restore power to the car and test the electric mirror control.

• 4) Post-assembly checks and test drive/function verification

  • Verify correct operation of electrical settings.
  • Check the strength of the mirror attachment and whether it does not move in its storage during normal handling.
  • Check that the mirror fits correctly on the door and that there are no excessive gaps.
  • When driving, watch for possible vibrations, noise from airflow or signs of insufficient tightening.

  5) The most common assembly mistakes + how to avoid them

  • Swapping left and right side – always verify that it is the driver’s side before fitting.
  • Electrical connection mismatch – compare the number of wires and the type of connector before installing the part.
  • Clamping of cabling – guide the cable freely and away from the contact surfaces.
  • Insufficient seat of the mirror – before tightening, check the correct fit to the door surface.
  • Damage to plastic covers during disassembly – use a suitable plastic pry bar and proceed with care.

  Reasons why the part is damaged

  • Damage while parking or contact with an obstacle
  • Impacts from passing vehicles or mechanical breakage
  • Cracking of the cover or glass due to an accident
  • Wear of electrical controls and wiring
  • Intrusion of moisture into the mechanical or electrical part of the mirror
  • Loose attachment due to vibration and long-term use