Description
Left rear view mirror for CITROEN Xsara Picasso cars
Electrically operated and foldable
Driver side 7 wires
We have different colors in stock
Part description
This used Citroën Xsara Picasso left wing mirror is suitable for vehicles of this model and is a practical solution for replacing a damaged original part. The mirror is electrically controlled and foldable, intended for the driver’s side, and is equipped with 7 wires.
The part is also searched by product number 815354. During the repair, you will especially appreciate the fact that it is a complete type of mirror designed for routine replacement of the original piece. There may be different color variants in the offer, so it is always advisable to check the visual design, the connector and the number of wires according to the dismantled part during assembly.
Technical information
- Manufacturer: Stellantis Citroën Peugeot
- Model: Citroën Xsara Picasso
- Other numbers: 815354
- Design: left rear view mirror
- Control: electrically controlled
- Function: electrically foldable
- Location: driver side
- Number of wires: 7
Product codes
- Product codes: 815354
- Models: Citroën Xsara Picasso
Installation recommendations
Generally/typically for rear-view mirror replacement, the exact procedure may vary depending on the specific car design and equipment. For this part, it is important to check especially the left side, electric control, folding and the number of wires before assembly.
1) Before assembly
- Check if it is the left driver side mirror.
- Compare the new and original part by shape, fit, connector and number of wires 7.
- Check the condition of the cover, mirror glass, attachment points and wiring.
- If the mirror is in a different color than the original part, consider transferring the cover or further modification according to the condition of the car.
2) Necessary tools and materials
- set of common hand tools
- plastic pry bar for panel removal
- suitable wrenches or attachments for fasteners
- clean cloth
- preparation for cleaning contacts, if needed
3) Step-by-step assembly procedure
- Turn off the ignition and secure the vehicle against movement.
- It is generally recommended to disconnect the battery, especially if you will be handling the electrical connectors.
- Remove the inner cover or trim in the mirror mounting area to gain access to the mounting and wiring.
- Carefully disconnect the electrical connector of the original mirror.
- Loosen the fasteners of the old mirror and hold it during removal to prevent it from falling and damaging the paintwork or the door.
- Compare the dismantled part with the spare part before assembly itself.
- Place the replacement mirror in the correct place and check that it fits against the body surface.
- Install and tighten fasteners evenly without over-tightening.
- Connect the electrical connector and check that the wiring is not pinched or unnecessarily stretched.
- Reinstall the cover parts and interior trim.
- Connect the battery if it was disconnected.
- Test all available mirror functions before normal use of the car.
-
4) Post-assembly checks and functional test verification
- Check the operation of the electric controls in all directions.
- Verify the correct operation of electric folding if it is active in the car.
- Make sure that the mirror is firmly held and does not have excessive play when handling.
- Check that there is no contact between the mirror and the body anywhere or that there is no tension in the wiring.
- When driving, check the stability of the mirror and the correct view.
5) The most common assembly mistakes + how to avoid them
- Swap Sides – Always verify it is the driver’s left side before fitting.
- Wiring mismatch – compare the connector and wire count with the old part.
- Door trim damage – use appropriate plastic tools and proceed with caution.
- Pinching of wiring – check the wiring before tightening the mirror.
- Insufficient seating of the part – after assembly, check the correct fit and strength of the attachment.
Reasons why the part is damaged
- mechanical damage when parking or passing through a narrow space
- impact from another vehicle, cyclist or obstacle
- damage to the folding mechanism due to long-term use
- wear of electrical controls or internal wiring
- cracking of the cover or glass due to age, vibration and weather conditions
