Description
Starter CL4 Mitsubishi for Citroën and Peugeot 1.8 16V, 2.0 16V and 2.2 16V.
This high-quality Starter CL4 is a direct-fit replacement unit designed for a range of Citroën and Peugeot petrol engines (1.8 16V, 2.0 16V, 2.2 16V). Ideal for professional workshops and DIY mechanics, the starter matches original equipment form, fit and function to restore reliable engine cranking and minimise downtime. Commonly searched under reference numbers such as 9656299480, M000T86081, 5802CY and 5802W5, this unit is suitable for fast identification and ordering on parts lists.
Technical Information
- Manufacturer: Mitsubishi (Original Equipment Supplier)
- Model: Citroën / Peugeot 1.8 16V, 2.0 16V, 2.2 16V Applications
- Product Codes: 9656299480, M000T86081, 5802CY
- Additional Numbers: 5802W5, 1638116380
Fitment
Typical vehicles that use this starter include:
- Citroën C4 (selected 1.8 / 2.0 16V petrol variants)
- Citroën C5 (selected 1.8 / 2.0 / 2.2 16V petrol variants)
- Peugeot 307 (selected 1.8 / 2.0 16V petrol variants)
- Peugeot 407 (selected 2.0 / 2.2 16V petrol variants)
Function And Typical Faults
The Starter Motor Converts Electrical Energy From The Battery Into Mechanical Rotation To Crank The Engine. Key Components Include The Pinion Gear, Bendix Drive, Solenoid, Armature And Brushes. Typical Failure Modes Are Worn Brushes Or Commutator, Solenoid Malfunction, Bendix Or Pinion Wear, Oil Contamination From Engine Leaks And Heat-Related Damage.
Why The Part Most Often Fails
- Wear Of Brushes And Commutator After High Mileage Or Aggressive Use.
- Frequent Short Trips Causing Heavy Cranking Cycles Without Full Recharge.
- Oil Or Coolant Leaks Contaminating The Starter Housing And Reducing Insulation.
- Corroded Or Loose Electrical Connections Causing Overheating Or Intermittent Operation.
- Damaged Bendix Or Ring Gear Teeth Due To Repeated Slipping Or Misengagement.
Replacement Procedure
General Steps For Replacement (Follow Vehicle Manufacturer Procedure):
- Disconnect The Negative Battery Cable Before Starting Work.
- Raise And Secure The Vehicle If Required To Access The Starter.
- Locate The Starter At The Bell Housing Area On The Engine/Transmission Interface.
- Label And Disconnect Electrical Connections: Battery Feed, Solenoid Wire And Any Additional Plugs.
- Support The Starter, Remove Mounting Bolts And Extract The Unit Carefully.
- Compare New Starter With Removed Unit For Mounting Orientation And Electrical Terminals.
- Install New Starter, Tighten Fasteners To Manufacturer Recommendations, Reconnect Wiring And Lower The Vehicle.
- Reconnect Battery And Verify Proper Engagement And Cranking Speed. Check For Unusual Noises Or Oil Leaks.
Installation Recommendations
- Always Disconnect The Battery Before Removing Or Installing The Starter To Prevent Short Circuits And Damage.
- Inspect Electrical Cables, Battery Condition And Earth Connections While Replacing The Starter — Poor Power Supply Is A Common Cause Of Premature Failure.
- Check The Flywheel Ring Gear For Damaged Teeth When Removing The Starter.
- Replace Mounting Hardware If Corroded And Ensure Correct Alignment To Prevent Bendix Misengagement.
- After Installation, Perform Several Crank Cycles With Engine Not Starting To Confirm Smooth Engagement, Then Start Engine And Recheck Fasteners.
Notes For Purchasers
Searches Are Often Performed Using The Part Numbers Listed Above. This Starter Offers Direct Compatibility With The Engines And Models Noted, Providing A Practical Solution For Mechanics And Enthusiasts Repairing Citroën And Peugeot Petrol Engines.
References / Codes: Stellantis CITROEN PEUGEOT • 9656299480 • M000T86081 • 5802CY • 5802W5 • 1638116380
