Description
Right passenger-side rear-view mirror for Stellantis vehicles
Electrically adjustable and heated, electrically foldable toward the vehicle
Color EJG – NUIT BLUE PAINT
FXT – CORNELIE BLACK
Driver’s door
7 PIN
Part Description
Used exterior rear-view mirror marked 98169900XT, with electric adjustment, heating, and electric folding toward the vehicle. It is a practical replacement if the mirror is damaged or its controls malfunction, provided it matches the original configuration. The information specifies a 7-pin connection and the color codes EJG – Nuit blue and FXT – Cornelie black.
Fitting-side warning: the product name specifies a left-hand mirror, while the original description specifies a right-hand passenger-side mirror as well as the driver’s door. The information is therefore contradictory on this point, and the side cannot be confirmed unambiguously. When selecting a part, compare the original part number, its shape, mounting, and connector; the pin count alone is not sufficient.
Technical Information
- Manufacturer: not specified; the information includes the designation Stellantis CITROEN PEUGEOT.
- Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
- Other numbers: not specified.
- Part type: exterior rear-view mirror.
- Condition: used part.
- Functions: electric adjustment, heating, and electric folding toward the vehicle.
- Connection: 7 PIN.
- Color codes: EJG – NUIT BLUE PAINT; FXT – CORNELIE BLACK.
- Fitting side: unclear due to contradictory information.
The model names are taken from the product labels. They do not by themselves determine whether the part is suitable for every version of the listed vehicles; what matters is whether the specific mirror and its electrical equipment match.
Product Codes
- Product codes: 98169900XT.
- Color code: EJG – NUIT BLUE PAINT.
- Additional color code: FXT – CORNELIE BLACK.
When searching for a replacement mirror using the number 98169900XT, also compare the side, base configuration, connector, and available functions with the removed part.
Installation Recommendations
The following procedure generally applies to electrically adjustable and folding rear-view mirrors. The exact access to the fasteners, removal of the trim, and power disconnection procedure depend on the specific model and vehicle configuration. Follow the manufacturer’s service procedure.
1) Before installation
- First resolve the discrepancy in the side designation by comparing the physical configuration with the original mirror.
- Compare the product number, base, mounting points, sealing surface, wiring routing, and connector shape, including the contact layout.
- Check the glass, cover, mount, joint, and wiring of the used part. Look for cracks, looseness, damaged insulation, or corroded contacts.
- Verify that the original mirror has the corresponding electrical functions. Do not force the folding mechanism.
2) Required tools and materials
Suitable hand tools for the fasteners used, plastic trim removal tools, protection for painted surfaces, and a soft cloth will usually suffice. For any electrical measurements, use an appropriate measuring instrument and the wiring diagram for the specific vehicle.
3) Step-by-step installation procedure
- Park the vehicle safely, switch off the ignition, and secure it against unintended operation.
- Following the manufacturer’s instructions, allow the electrical systems to enter their idle state and disconnect the power supply as specified.
- Protect the surrounding painted surfaces and carefully remove only the covers or trim needed to access the mounting and connector.
- Note the original wiring route. Release the connector lock and disconnect it without pulling on the wires.
- Support the mirror and gradually release its fasteners so it does not fall and damage the door.
- Remove the original part, clean the mounting surface, and check the condition of the seal and the vehicle’s mounting points.
- Compare the two parts again. If the side, base, or electrical connection does not match, do not continue with the installation.
- Position the replacement mirror without pinching the wiring or seal. Tighten the fasteners according to the manufacturer’s service procedure.
- Route the wiring along its original path, secure it, and connect the connector so that its lock engages correctly.
- Restore the power supply according to the manufacturer’s instructions, check the functions, and refit the removed covers and trim.
4) Post-installation checks and function testing
- Test the electric glass adjustment and folding and unfolding. Movement should be smooth and free of unusual noises.
- Check the heating under the conditions in which the specific vehicle activates it.
- Check that the mirror is securely mounted, the seal is seated correctly, and the trim is fitted properly.
- Adjust the view before driving. During a short test drive, watch for image vibration or unusual aerodynamic noise; test folding while the vehicle is stationary.
5) Common installation mistakes and how to avoid them
- Incorrect side or equipment: compare the physical configuration and electrical connection; do not rely solely on the product name.
- Pinched wiring: check its route and ensure there is enough clearance before tightening.
- Damage to mounting points from overtightening: follow the manufacturer’s procedure and do not use excessive force.
- Improperly seated seal: clean the mounting surface and check that the seal sits evenly.
- Forcing the mirror to fold or connecting power incorrectly: operate the mechanism as intended and perform electrical tests only if you understand the wiring.
Reasons for Part Damage
Common causes of damage to this type of rear-view mirror include:
- Impacts while parking or passing obstacles, which can damage the cover, glass, joint, or mounting.
- Forcing the mirror to fold or moving it against an obstacle or ice, which can overload the folding mechanism.
- Moisture and contact corrosion, which can interfere with electric adjustment or heating.
- Wear of moving parts through prolonged use.
- Damaged wires or incorrect previous installation, for example pinched wiring or inadequate sealing.
These causes are general and do not describe any faults identified in the item offered.
