Description
Rear right tail light lamp for Citroën Xsara Picasso up to 2004
Passenger Side
Original Citroën
Product Overview
High-quality Rear Right Tail Light designed as an original Citroën replacement for the Xsara Picasso (models produced up to 2004). This passenger-side combination lamp restores the correct rear lighting functions and appearance after damage or wear. Ideal for professional garages and DIY mechanics who need a direct-fit, OEM-style unit identified frequently by part numbers 9631563980 and 6351N0.
Key Features
- Direct Fit For Passenger Side: Designed to match the mounting points and connector layout of Citroën Xsara Picasso (up to 2004).
- OEM Quality: Marketed as an original Citroën unit, ensuring correct lens geometry, reflector position and finish.
- Combination Lamp Functionality: Provides Rear Position (Tail), Brake and Turn Signal lighting in a single assembly; may also include reverse or fog lamp depending on vehicle variant.
- Simple Replacement: Bolt-on design with a plug-in electrical connector for straightforward installation in workshop or home settings.
- Searchable By Part Number: Frequently listed and searched using codes 9631563980 and 6351N0—useful for quick identification.
How It Works And Typical Applications
This rear right lamp is a combination unit that houses the rear position (tail) lamp, stop (brake) lamp and direction indicator. When fitted to the vehicle it ensures compliance with rear lighting functions and optical alignment so other road users can clearly see braking and turning signals. It is suitable for Xsara Picasso models produced until 2004 and intended as a replacement for damaged or non-functioning original rear-right lamps.
Installation Guide
Recommended For Trained Mechanics And Competent DIYers:
- Open The Tailgate/Boot And Remove Interior Trim To Access Lamp Fasteners.
- Unscrew The Mounting Bolts And Carefully Pull The Lamp Assembly Outwards From The Body.
- Disconnect The Electrical Connector By Releasing The Locking Clip, Then Remove The Lamp Assembly.
- Install The New Lamp By Plugging In The Connector, Seating The Lamp Correctly And Replacing The Mounting Bolts.
- Test All Light Functions (Tail, Brake, Indicator And Reverse If Applicable) Before Reinstalling Trim.
Always Follow Common-Sense Safety Procedures: Disconnecting the battery is recommended when working on vehicle electrics to reduce risk of short circuits. Tighten fasteners to manufacturer torque where available and check the lamp alignment after installation.
Technical Information
- Manufacturer: Citroën
- Model: Citroën Xsara Picasso (Up To 2004)
- Product Codes: 9631563980, 6351N0
- Additional Numbers: (6351.N0), (N68)
Recommendations For Mounting
- Inspect The Connector And Wiring For Corrosion Or Damage Before Fitting The New Lamp.
- Replace Bulbs As Necessary With Correct Types Specified In The Vehicle Manual; If Reusing Old Bulbs, Check Sockets For Corrosion.
- Ensure Sealing Surfaces Are Clean And Free Of Old Sealant To Prevent Water Ingress.
- After Installation, Verify That All Light Functions Operate Correctly And That The Lens Sits Flush With The Bodywork.
Why This Part Typically Fails
- Bulb Burnout: The most common cause of apparent lamp failure—individual bulbs within the assembly reach end of life.
- Water Ingress And Condensation: Cracked lenses or degraded seals allow moisture into the housing, causing corrosion of contacts and premature failure.
- Impact Damage: Rear collisions or knocks can crack the lens or break mountings, necessitating lamp replacement.
- Connector Corrosion Or Wiring Faults: Corroded pins or damaged wiring can cause intermittent operation or full failure of one or more lamp functions.
Who Should Fit This Part
Suitable For Professional Auto Technicians And Experienced DIY Enthusiasts. If You Are Unsure About Electrical Work Or Lamp Alignment, Seek Assistance From A Qualified Workshop.
