Description
Right rear ORIGINAL lamp for CITROEN BERLINGO and PEUGEOT PARTNER
Double rear door
Without bulb socket
Part description
This right rear lamp is intended for Citroën Berlingo and Peugeot Partner cars with double rear doors. It is an original used car part that is suitable as a replacement for a damaged or non-functioning rear light.
The part is supplied without a bulb socket, so before assembly it is necessary to check the condition of the original socket and, if necessary, use it from the existing lamp. For auto mechanics and home repairs, it is also important to compare the shape, attachment and product codes so that the assembly takes place without unnecessary complications.
The rear lamp is of fundamental importance for traffic safety and the correct visibility of the car. Replacing a damaged light will help to restore the full functionality of the rear lighting and at the same time keep the appearance of the car in an appropriate condition.
Technical information
- Manufacturer: Stellantis Citroën Peugeot
- Model: Citroën Berlingo, Peugeot Partner
- Other numbers: 6351Z0, 6351CX
- Design: right rear lamp
- Designed for: double-leaf rear door
- Included in the package: without bulb socket
Product codes
Product codes: 6351Z0, 6351CX
- Citroën Berlingo
- Peugeot Partner
Installation recommendations
For this part, assembly according to the specific design of the car applies. According to the documents supplied, it is a right rear lamp for Citroën Berlingo and Peugeot Partner cars with two-wing rear doors, while the part is without bulb socket. In general, the following procedure applies to this type of part:
1) Before assembly
- Check that the right side, lamp shape, mount and product codes 6351Z0 and 6351CX match.
- Compare the new and original part visually, especially the attachment points, seating surfaces and the connector part.
- Since the lamp is supplied without a bulb socket, please check the condition of the original socket, contacts and wiring.
- Check for a cracked lamp body, damaged gasket, or broken mounting hardware.
2) Necessary tools and materials
- Basic set of hand tools
- Suitable screwdriver or socket wrench depending on the type of attachment
- Clean cloth
- Preparation for cleaning contacts, if needed
- Protective gloves
3) Step-by-step assembly procedure
- Turn off the ignition and secure the vehicle against movement.
- Access the rear part of the lamp from the inside of the door or the body according to the specific design of the car.
- Disconnect the electrical connector from the original lamp.
- Dismantle the fasteners of the old lamp and remove it carefully so as not to damage the surrounding paint or plastics.
- Transfer the bulb socket from the original part if it is OK and usable for this part.
- Clean the mounting surface and check the mounting area for dirt or signs of leakage.
- Sit the lamp into place and check for proper seating in all guide and fixing points.
- Install the fasteners and tighten them evenly so as not to stress the plastic body of the lamp.
- Connect the electrical connector and verify that the connection is tight and free of play.
- After mechanical seating, check the alignment of the lamp with the surrounding parts of the body and doors.
-
4) Post-assembly checks and test drive/function verification
- Try out all the lighting functions that the lamp provides according to the car’s equipment.
- Check that the light shines steadily and without contact failures.
- Check that the lamp is seated correctly and that there is no unwanted play anywhere.
- After a short drive or after slamming the door, check the fastening and functionality again.
5) The most common assembly mistakes + how to avoid them
- Swap part side – always verify it is the right rear lamp before fitting.
- Using a damaged bulb socket – check the contacts, traces of overheating and mechanical damage before handing over.
- Too much tightening of the fixture – can lead to plastic cracking or poor seating of the lamp.
- Insufficient function check after installation – always test the lighting before completing the work.
- Damage when reversing, parking or a minor impact to the rear of the car
- Plastic cracking due to mechanical impact
- Moisture entering the lamp and subsequent deterioration of the lighting function
- Wear of bulb socket contacts or connector connection
- Aging of material and reduction of transparency or strength of plastic parts
