Description
Seat belt buckle for various CITROEN, PEUGEOT and other Stellantis models
Long – for the front passenger seat cushion
Part description
This used seat belt buckle with product number 9816315480 in the long version is intended for the front passenger seat. It secures the seat belt tongue and releases it when getting out. Correctly fastening and reliably holding the belt are essential for passenger safety.
The documentation lists this part for the Citroën Berlingo K9, PEUGEOT RIFTER and the other vehicles listed below. When selecting a part, compare the number 9816315480, length version and mounting with the original buckle. The model name alone may not distinguish all seat belt versions.
Technical information
- Manufacturer: Stellantis – designation stated in the documentation.
- Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
- Part type: seat belt buckle.
- Version: long.
- Application: front passenger seat cushion.
- Condition: used part.
- Other numbers: not specified.
Product codes
- Product codes: 9816315480.
The product number is an important reference when looking for a replacement Citroën or Peugeot seat belt buckle. Before installation, the design of the original and replacement parts must also be compared.
Installation recommendations
General guidelines for this type of part: the seat belt buckle is part of the safety system. The exact procedure for removal, fastening and any electrical connection depends on the specific model and vehicle version. The documentation does not state whether an electrical sensor or other system components are present. We recommend having the replacement carried out by a qualified mechanic and following the manufacturer’s service procedure.
1) Before installation
- Compare the product number, length, shape, mounting and any connectors with the old part.
- Inspect the housing, mounting section and belt tongue entry. The part must not show cracks, deformation, significant corrosion or signs of tampering.
- Check that the release button operates smoothly and that the corresponding tongue locks securely. This check does not replace a professional safety assessment.
- Do not install a part showing signs of accident loading or whose safe condition is in doubt. After an accident, follow the manufacturer’s instructions for the entire restraint system.
2) Required tools and materials
Typically, suitable hand tools for the fasteners in question, a torque wrench, and, if needed, tools for carefully removing trim, a clean cloth and the vehicle’s service documentation are required. Whether new fasteners are needed depends on the manufacturer’s instructions.
3) Step-by-step installation procedure
- Secure the vehicle against movement, switch off the ignition and ensure safe access to the work area.
- Refer to the service documentation for the replacement procedure and safety precautions for the specific restraint system version.
- If the work involves the electrical part of the restraint system, disconnect the battery and observe the waiting time specified by the manufacturer.
- Carefully remove any covers or other parts obstructing access, as needed. Note the orientation of the original buckle and the routing of any wiring.
- If the buckle is electrically connected, release the connector lock and disconnect it without pulling on the wires.
- Undo the fastener and remove the original buckle. Inspect the contact surfaces and mounting point; do not proceed with installation if they are damaged.
- Compare the two parts again and position the replacement buckle in the correct orientation, without twisting or mechanical strain.
- Tighten the fastener according to the manufacturer’s service specifications. If the manufacturer requires the fasteners to be replaced, do not reuse the original ones.
- Connect and secure any wiring so that it is not pinched or stretched when the seat moves. Refit any covers that were removed.
- Restore the power supply according to the manufacturer’s procedure, if it was disconnected, and check operation before using the vehicle.
4) Post-installation checks and function verification
With the vehicle stationary, fasten and unfasten the belt several times. The tongue must click clearly into place, remain secured when pulled with moderate force, and release when the button is pressed. Check that the buckle is securely mounted and readily accessible with the seat in its normal adjustment range. If the vehicle has a seat belt warning system, also check that it works. If there is a fault or restraint system warning, do not use the passenger seat until the cause has been resolved. A test drive does not replace a safety function check.
5) Common installation errors and how to prevent them
- Confusing the length or version: compare both the number and the physical characteristics of the two parts before installation.
- Incorrect orientation or tightening: follow the service procedure and do not guess instead of using the specified values.
- Pinched wiring: route any wires away from moving parts and check them throughout the seat’s adjustment range.
- Lubricating or disassembling the mechanism without the manufacturer’s instructions: do not spray universal lubricants into the buckle or interfere with its internal components.
Reasons why the part may become damaged
The following general causes of damage may affect seat belt buckles; they do not describe the condition of the item offered:
- Mechanism wear from fastening and unfastening the belt over an extended period.
- Dirt or foreign objects preventing the tongue from being fully inserted and secured.
- Spills and moisture, which may cause corrosion or damage any electrical contacts.
- Mechanical stress, impacts, pinching or forcefully inserting an unsuitable tongue.
- Accident loading, which may also cause damage that is not immediately apparent.
- Improper installation, incorrect fastening or damage to any wiring.





