Description
Driver’s sun visor for vehicles from the Stellantis group
This is a used item and may be slightly soiled
Part description
Driver’s sun visor Citroën Peugeot Opel 98094985BJ helps reduce sun glare and improve visibility while driving. It is a used interior part that can serve as a replacement for a damaged, sagging, or missing visor. When selecting one, it is important to compare not only the product number, but also the design and mounting points with the original part.
The available information lists the part for Citroën Berlingo K9, OPEL COMBO E K9, PEUGEOT PARTNER III, and PEUGEOT RIFTER models. Any slight soiling is consistent with the stated condition of this used item. The specific features of the visor, such as a mirror or lighting, are not specified.
Technical information
- Manufacturer: not specified; the designation Stellantis / CITROEN PEUGEOT is listed in the available information.
- Model: Citroën Berlingo K9 | OPEL COMBO E K9 | PEUGEOT PARTNER III | PEUGEOT RIFTER.
- Part type: driver’s sun visor.
- Condition: used item, may be slightly soiled.
- Other numbers: not specified.
Product codes
- Product codes: 98094985BJ.
The number 98094985BJ is the main identifier for finding this part. Before replacement, compare it with the marking on the original visor and check that the design matches.
Installation recommendations
The following procedure is general and typical for replacing a sun visor. The exact mounting, method for releasing the covers, and any electrical connection depend on the specific model and vehicle configuration.
1) Before installation
- Compare the part number, shape, dimensions, position of the brackets, and method of attachment with the old visor.
- Inspect the visor body, support arm, and mounting parts. Check that they are not cracked or significantly loose.
- Carefully check the joint’s movement and the visor’s ability to hold its set position. Do not turn the mechanism past its natural stops.
- If the visor has an electrical connection, compare the connector and cable routing as well. This feature is not confirmed for the item offered.
2) Tools and materials required
- Hand tools suitable for the actual fasteners.
- A plastic tool for gently releasing covers, if fitted.
- A clean, soft cloth and a product suitable for the interior surface in question.
- A container for removed screws and small parts.
3) Step-by-step installation procedure
- Park the vehicle safely, switch off the ignition, and ensure there is sufficient light for the work.
- Inspect the original visor’s mounting and note the orientation of the brackets, covers, and any cable.
- If the visor has an electrical connection, follow the vehicle manufacturer’s instructions for disconnecting the power supply before unplugging it.
- Support the visor and carefully release any mounting covers. Do not pry against the trim or use excessive force.
- Release the fasteners in a manner appropriate to their design. Continue supporting the visor so that it does not place strain on the remaining mounting points.
- If there is a connector, release its lock and disconnect it by holding the connector body, not by pulling on the wires. Remove the original visor.
- Check the condition of the mounting points and the surrounding trim. Repair any damaged mounting points first; replacing the visor alone will not fix the damage.
- Position the replacement visor correctly and check that it fits without forcing it into place. If applicable, connect the connector and route the cable so that it cannot be pinched.
- Secure the mounting according to its design and the vehicle manufacturer’s instructions. Do not overtighten screws or strain plastic parts by deforming them.
- Refit the covers and check that they are seated properly. If the power supply was disconnected, restore it according to the vehicle manufacturer’s procedure.
4) Post-installation checks and function verification
- Fold the visor down and return it to its original position several times. It should move smoothly and remain securely mounted.
- Check that the visor holds its set position, does not drop on its own, and does not obstruct a safe view.
- If the design allows, also check its sideways movement and how it secures in the retaining clip.
- Test any lighting only if it is part of the specific configuration.
- After a successful stationary check, listen for any knocking or spontaneous folding during a short test drive. Secure a loose visor again before driving.
5) Common installation errors and how to avoid them
- Incorrect configuration: before removal, compare the product number, mounting points, and any electrical connection.
- Breaking covers or clips: first determine how they are secured and release them with a suitable plastic tool.
- Overtightening the fasteners: use appropriate hand tools and follow the manufacturer’s instructions.
- Pinching the cable: on a visor with electrical equipment, check the wire routing before final fastening.
- Leaving a damaged bracket in place: check the entire mounting, not just the visor itself.
Reasons why the part gets damaged
Sun visor faults are generally caused primarily by mechanical wear and stress during use. The following causes do not describe any defects found on the item offered:
- Joint wear from repeated folding can make the visor less able to hold its position or cause it to drop on its own.
- Forcing it past its stop can damage the arm, joint, or bracket.
- Prolonged exposure to heat and sunlight contributes to the aging of plastics and surface materials.
- Hanging objects from the visor places unnecessary strain on the mechanism and mounting.
- Careless removal or overtightening screws can cause mounting parts to crack.
- Unsuitable cleaning can damage the surface; test the cleaning product on an inconspicuous area first and avoid soaking the visor unnecessarily.
