This VALEO A/C compressor is an OEM-quality unit originally fitted to multiple Stellantis models. It is a direct-fit replacement for vehicles listed under the corresponding product numbers and is especially useful for professional workshops and experienced DIY mechanics searching by part number 9827528980, 9827552180 or 1617294480. The unit was removed from a car with 64,000 km and is ready for installation after standard installation procedures.

Key Benefits

• Direct-fit design for easy replacement on compatible Citroën and Peugeot models.
• High-quality Valeo manufacturing ensures correct clutch and pulley alignment.
• Saves diagnostic and repair time when identified by OEM product numbers: 9827528980, 9827552180, 1617294480.
• Suitable for professional repair shops and experienced DIY mechanics familiar with A/C service procedures.

Technical Information

• Manufacturer: Valeo
• Model: Commonly fitted to Citroën/Peugeot/DS platforms such as Citroën Berlingo (B9/III), Citroën C2, C3, C4 II, Citroën DS4, Peugeot 206, 307, 308 (T9), Peugeot Partner (III), Peugeot Rifter, XSARA, XSARA Picasso (check product numbers for exact fitment)
• Product Codes: 9827528980, 9827552180, 1617294480
• Other Numbers: 9827528980-02, 9827552180-02, Alternate references: 9827528980 / 9827552180 / 1617294480

Function And Compatibility

The compressor is the heart of the vehicle air conditioning system: it circulates refrigerant under pressure, enabling heat exchange in the condenser and evaporator and delivering cooled air to the cabin. Depending on the vehicle specification, the compressor is used in systems charged with R134a or R1234yf refrigerant; confirm the refrigerant type for the particular vehicle model and production year before service.

Common Failure Causes

• Mechanical wear of bearings and clutch assembly leading to noise or seizure.
• Loss of lubrication caused by system leaks or prolonged low refrigerant level.
• Contamination from a failed condenser, dryer/accumulator, or compressor internals causing internal damage.
• Electrical faults in the clutch coil or wiring preventing compressor engagement.

Replacement Guide

Recommended steps for replacement (intended for trained technicians or experienced DIY mechanics with proper equipment):

• Recover refrigerant from the system using certified recovery equipment.
• Disconnect the battery before starting work to avoid electrical damage.
• Remove drive belt and electrical connectors from the compressor.
• Cap or plug A/C lines when disconnected to prevent moisture ingress and contamination.
• Remove compressor mounting bolts and extract the unit. Replace any damaged mounting hardware.
• Replace all A/C O-rings with appropriate sizes and lubricate with the correct type and amount of PAG oil as specified for the vehicle.
• Install the new compressor, tighten fasteners to manufacturer torque values, reconnect lines and electrical connectors.
• Evacuate the system to remove moisture and check for leaks, then charge with the correct refrigerant type and specified quantity.
• Run the system and verify proper operation, checking compressor clutch engagement, system pressures, and cabin cooling performance.

Installation Recommendations

• Always replace the receiver/drier or accumulator and expansion valve/orifice tube when opening the system, especially if contamination is suspected.
• Use the specified type and volume of compressor oil (PAG grade) for the particular vehicle system; incorrect oil will reduce service life.
• Perform a vacuum test for at least 30 minutes to ensure no leaks and to remove moisture before charging.
• Do not run the compressor without refrigerant and oil—this causes rapid internal damage.
• After installation, inspect belt tension and pulley alignment to prevent premature wear.

Why The Part Most Often Fails

The most frequent cause of compressor failure is inadequate lubrication due to refrigerant leaks or system contamination. When the system loses refrigerant, it also loses oil circulation, causing bearings and internal components to overheat and wear quickly. Contaminants from a failing condenser or a ruptured dryer can further damage internal valves and pistons, leading to seizure or internal scoring.

Search Tips

For fast identification use the OEM product numbers 9827528980, 9827552180 or 1617294480 when searching. These references improve the chance of finding the correct fitment for Citroën, Peugeot and associated models.

This air conditioning pipe is a direct-fit component designed for PSA/Stellantis family vehicles and referenced under OEM numbers 9675635380 and 9840709880. Ideal for professional workshops and experienced DIY mechanics, the pipe restores proper refrigerant flow, reduces leak risk at affected connections and helps the A/C system reach designed cooling performance. Use the part numbers in searches to quickly find the exact fit for your vehicle.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën Berlingo III (from 2018), Citroën C4 II, Peugeot 308 (T9), Peugeot 3008 I, Peugeot Partner III (from 2018), Peugeot Rifter, Opel Combo E K9
• Product Codes: 9675635380, 9840709880
• Additional Numbers: R1234yf, R134A (refrigerant compatibility indicated)

Function And Benefits

The pipe conveys refrigerant between components of the air conditioning circuit (compressor, condenser, evaporator and expansion valve). A correct, undamaged pipe maintains system pressure, prevents leaks and ensures reliable cooling. Replacement restores system integrity where cracks, corrosion or failed connections have allowed refrigerant loss.

Replacement Procedure (Overview)

• Recover refrigerant from the system using certified A/C recovery equipment; handling refrigerants requires appropriate tools and certification.
• Remove protective covers and disconnect affected fittings. Inspect mating surfaces and replace O-rings/seals with manufacturer-specified types.
• Fit the new pipe, ensuring correct routing and torque of fittings to avoid stress or chafing.
• Evacuate the system with a vacuum pump to remove moisture and check for leaks using a suitable method (vacuum hold test or electronic leak detector).
• Recharge the system with the correct refrigerant type and specified charge mass for the vehicle. Run and test the A/C to confirm proper pressure and temperature.

Recommendations For Installation

• Use new O-rings lubricated with the correct oil for the refrigerant in the vehicle (follow manufacturer specifications).
• Ensure correct refrigerant type (R1234yf or R134A) and lubricant are used for the specific vehicle application.
• Avoid over-tightening fittings; follow torque values where available to prevent damage to threads and sealing surfaces.
• Replace any corroded clamps, brackets or insulation that could abrade the new pipe.
• Perform a full system evacuation and leak test before charging; verify system pressures and cabin cooling performance after service.

Why This Part Most Commonly Fails

• Corrosion From Road Salt And Moisture: Metal pipes and fittings can corrode, especially at joints and exposed sections.
• Mechanical Damage: Stone impact, road debris or contact with other components can dent or puncture the pipe.
• Degraded Seals And O-Rings: Aging rubber seals lose elasticity and start leaking at connection points.
• Vibration And Stress: Poor routing or broken mounts allow movement that fatigues the pipe over time.

Search Tags And Keywords: air conditioning pipe, AC pipe, A/C hose, 9675635380, 9840709880, Citroën Berlingo AC pipe, Peugeot 308 AC pipe, Peugeot 3008 AC pipe, Peugeot Partner AC pipe, RIFTER AC pipe, Opel Combo E K9 AC pipe.

This direct-fit air conditioning (A/C) pipe is designed for Citroën and Peugeot models and is identified by part numbers 9675102080 and 9831702080. Ideal for professional workshops and experienced DIY mechanics, the pipe provides reliable routing of refrigerant between system components and restores proper airflow and cooling when the original line is leaking or damaged. Searchable by OEM numbers, it helps you find the correct replacement quickly and reduce vehicle downtime.

Compatibility

• Citroën Berlingo (Model From 2018)
• Peugeot Partner (Model From 2018)
• Peugeot Rifter
• Peugeot 308

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën Berlingo, Peugeot Partner, Peugeot Rifter, Peugeot 308
• Product Codes: 9675102080, 9831702080
• Additional Numbers: R1234yf, R134A

Installation Recommendation

Replacement of an A/C pipe requires handling of refrigerant and should be carried out with appropriate workshop equipment. Recommended procedure:

• Recover and evacuate refrigerant professionally with certified recovery equipment before opening the system.
• Replace all O-rings and seals at connections with the correct sizes and material (lubricated with the correct PAG oil as per manufacturer specification).
• Visually inspect adjacent components (compressor, condenser, evaporator, mounting brackets) for damage or corrosion and replace any worn clamps or fasteners.
• Perform a vacuum test to at least manufacturer-recommended vacuum level and hold time to verify system tightness.
• Recharge the system with the correct type and amount of refrigerant and oil per vehicle specification; perform leak check and functional test.
• Observe safety precautions: wear protective equipment and follow local regulations for refrigerant handling.

Why This Part Commonly Fails

• Corrosion: Exposure to road salt and moisture causes fittings and pipe surfaces to corrode and develop leaks.
• Mechanical Damage: Impact from road debris or incorrect handling during repairs can dent or puncture the line.
• Vibration and Fatigue: Repeated vibration and movement can stress joints and cause cracks at bends or connection points.
• Seal Degradation: O-rings and sealing faces age, harden or become brittle, producing leaks at the connections.
• Improper Installation: Incorrect O-ring selection, insufficient tightening or damaged mounting brackets lead to premature failure.

Notes For Professionals And DIYers

Part numbers 9675102080 and 9831702080 are commonly used search terms — including them in your order or parts request speeds identification. Always confirm the refrigerant type used in the vehicle before starting work and service the system to manufacturer charging specifications. For best results, replace associated seals and inspect nearby components when swapping the pipe.

Designed to meet the demands of routine workshop replacement, this A/C pipe is a practical solution to restore cooling performance on compatible Citroën and Peugeot models.

This Air Conditioning Pipe is designed specifically for Citroën Berlingo (from 2018), Peugeot Partner (from 2018), and Rifter models. It plays a crucial role in the vehicle’s climate control system, allowing the seamless flow of refrigerant between components. Reliable and durable, this pipe ensures optimal cooling performance, essential for maintaining cabin comfort during all seasons.

Function and Importance

The air conditioning pipe transports refrigerant under high pressure, connecting the compressor, condenser, and evaporator. Its integrity is vital for preventing leaks that can reduce system efficiency and lead to compressor damage. Over time, these pipes may fail due to exposure to heat, vibrations, or mechanical wear, causing loss of refrigerant and diminished air conditioning functionality.

Replacement and Compatibility

Replacing this pipe is recommended when leaks or cracks are detected or during significant climate system repairs. Installation typically requires professional tools to safely evacuate refrigerant and avoid contamination. Compatible with Citroën Berlingo, Peugeot Partner, and Rifter models from 2018 onward, this part can often be identified by its product number 9807256280, facilitating accurate sourcing.

Technical Information

• Manufacturer: PSA (Peugeot Citroën)
• Model Compatibility: Citroën Berlingo (2018+), Peugeot Partner (2018+), Rifter
• Product Codes: 9807256280
• Additional Numbers: Not specified

Summary

This air conditioning pipe is an essential replacement part ensuring the longevity and efficiency of the climate control system in selected Citroën and Peugeot vehicles. Its compatibility and original product code make it an indispensable choice for professional mechanics and DIY car enthusiasts aiming to restore optimal air conditioning performance.