This high-quality replacement electric window motor is designed for Peugeot 3008 I and 5008 I vehicles and carries OE references 9682808680, 1607674980 and 9224F6. Ideal for professional garages and skilled DIY enthusiasts, the unit restores smooth and reliable rear right window operation, reducing noise and intermittent failures common with worn motors. Compatible with original mounting points and electrical connectors, it provides a cost-effective solution to a stuck or non-responsive rear passenger window.

The unit converts electrical energy into rotational motion that drives the window regulator mechanism. When the switch is operated, the motor turns the regulator gear or spool, raising or lowering the glass. Typical faults include electrical brush wear, gear damage or water ingress that affects the motor and contacts.

Installation Recommendations

• Prepare Tools: Trim panel tools, Torx/Screwdrivers, socket set and a multimeter for quick checks.
• Safety First: Disconnect the battery before starting work to avoid short circuits and accidental airbag deployment.
• Support The Glass: Secure the window glass in the up or down position with tape or a support to prevent it falling when the motor/regulator is removed.
• Remove Door Trim: Carefully detach door card, unplug electrical connectors for switches and speakers, and remove the moisture barrier if present.
• Unbolt The Motor/Regulator: Remove fasteners holding the motor and regulator assembly, disconnect the electrical connector and extract the unit from the door cavity.
• Fitment: Transfer any required mounting brackets or bolts from the old unit if applicable, fit the new motor, reconnect the plug and temporarily reconnect the battery to test function before fully reassembling the door.
• Final Checks: Verify smooth travel of the window across the full range, adjust glass alignment if necessary, re-fit the door trim and perform a final functional test.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I; Peugeot 5008 I
• Product Codes: 9682808680
• Additional Numbers: 1607674980; 9224F6
• Application: Right Rear Passenger Side Electric Window Motor

Why This Part Most Often Fails

• Water Ingress: Moisture entering the door cavity corrodes electrical contacts and brushes, accelerating failure.
• Wear Of Brushes/Commutator: Normal operation causes wear of internal brushes and commutator, leading to intermittent or no movement.
• Mechanical Damage: Stripped gears, broken teeth or worn regulator components can overload the motor and cause it to stall.
• Contamination And Lack Of Lubrication: Dirt and dried grease increase friction on tracks and cables, putting extra load on the motor.
• Frequent Use And Age: High cycle use over several years increases the likelihood of failure compared to lightly used vehicles.

Practical Tips: Always check the condition of the regulator mechanism and guide rails when replacing the motor. Clean and lubricate tracks, replace worn clips or cables, and verify electrical supply and grounding if intermittent operation is observed. Test the new motor before refitting the door card to ensure correct installation.

High-quality replacement rear parking sensor wiring harness designed for Peugeot 3008 first generation (PDC). This wiring loom connects the ultrasonic sensors mounted in the rear bumper to the vehicle’s parking aid system, ensuring reliable signal transmission and correct operation of the Park Distance Control (PDC). Ideal for professional mechanics and experienced DIY enthusiasts searching by part numbers 9665188480 or 6528Y4.

What It Does

The harness transmits power and sensor signals between the rear ultrasonic sensors and the vehicle’s PDC control module. A correctly fitted loom guarantees accurate obstacle detection, reliable audible/visual alerts when reversing, and prevents intermittent faults caused by poor connections or damaged wiring.

Suitable Models

• Peugeot 3008 I (First Generation, typically 2008–2016)

Technical Information

• Manufacturer: Stellantis (Peugeot / Citroën)
• Model: Peugeot 3008 I (First Generation)
• Product Codes: 9665188480, 6528Y4
• Additional Numbers: 6528.Y4, P84, (T84)

Installation Recommendations

Replacement is straightforward for a trained technician and feasible for competent DIYers with basic tools. Typical steps:

• Disconnect the battery before any electrical work to avoid short circuits.
• Remove the rear bumper following the vehicle manufacturer’s procedure to access the harness and sensors.
• Unplug sensor connectors and detach the old loom from clips and guides.
• Route the new harness along the original routing, secure with the original clips or suitable replacements, and reconnect sensor plugs.
• Reassemble the bumper and reconnect the battery. Test the parking sensors by engaging reverse gear and verifying audible/visual warnings or using a diagnostic tool if available.

Use dielectric grease on exposed connectors to improve moisture resistance. Inspect clips and grommets and replace any damaged mounts to prevent chafing.

Why This Part Fails

• Corrosion and Water Ingress: Moisture can corrode pins and connectors, causing intermittent or permanent loss of signal.
• Mechanical Damage: Rear impacts or improper bumper removal/installation can crush or tear the loom.
• Chafing and Abrasion: Poor routing or broken clips allow the harness to rub against metal edges and wear through insulation.
• Rodent Damage: Chewing by rodents can sever conductors.

Notes For Professionals

When replacing the rear PDC harness, inspect individual sensors and the PDC control unit for fault codes after installation. Faulty sensors or damaged contacts at the control unit may mimic a harness fault. Secure all connections and restore original routing to maintain long-term reliability.