P06-00 – Used Parts Vendor https://www.usedpartsvendor.com Citroën Peugeot spare parts Mon, 13 Apr 2026 12:40:41 +0000 en-GB hourly 1 https://wordpress.org/?v=6.9.4 BSI 2004 P06-00 Citroën Peugeot 9659285380 https://www.usedpartsvendor.com/electro-components/control-units/bsi-comfort-unit/bsi-2004-p06-00-citroen-peugeot-9659285380/ Thu, 15 Jan 2026 03:01:08 +0000 https://www.usedpartsvendor.com/uncategorized/bsi-2004-p06-00-citroen-peugeot-9659285380/ BSI 2004 P06-00 VALEO intelligent unit for CITROEN PEUGEOT cars

Part description

This BSI (Body Systems Interface) comfort unit serves as a central electronic module for controlling and communicating selected comfort and body functions of the vehicle. The offered part is marked BSI 2004 P06-00 from the manufacturer VALEO and is intended for cars of the Citroën / Peugeot concern. It is often searched and identified by product number, so we recommend that you compare all the codes from the label with the original unit when choosing.

According to the labels, the part is associated with the models: Citroën C3, Citroën C3 II, Peugeot 207.

Technical information

  • Manufacturer: VALEO
  • Model: Citroën C3 | Citroën C3 II | Peugeot 207
  • Other numbers: 1663372580, 6580X4, 6580NG, 6580X5, 6580NH

Product codes

  • Product codes: 9659285380

Installation recommendations

The exact procedure may vary according to the specific model and equipment of the car. Below is the general/typical procedure for replacing the BSI comfort unit on Citroën/Peugeot cars.

1) Before assembly

  • Compare all codes on the unit (especially 9659285380 and other numbers listed) to the old part.
  • Check for damage to connectors, connector locks and pins (bent, oxidized, pulled).
  • Visually verify that the unit cover is not cracked and does not show signs of moisture.

2) Necessary tools and materials

  • Basic set of hand tools (screwdrivers/ratchet depending on design)
  • Plastic pry bar for removing covers (to minimize plastic damage)
  • Electrical contact cleaner (optional) and dry cloth
  • Diagnostics / option to configure the unit (according to service equipment)

3) Step-by-step assembly procedure

  1. Turn off the ignition, remove the key and allow the vehicle to idle for a short time (typically a few minutes).
  2. Disconnect the battery (minus pole first) to avoid damaging the electronics.
  3. Ensure access to the BSI unit (remove the necessary covers/panels according to the car).
  4. Document the connection: take a picture of the connectors and their location, or mark them.
  5. Gradually unlock the connector locks and disconnect the connectors carefully (do not pull on the cables).
  6. Unfasten the drive and remove the drive.
  7. Compare the old and new piece (codes, connectors, mechanical attachment).
  8. Install the unit in place and secure it in its original mounting.
  9. Connect the connectors in the correct order, all locks must clearly “click”.
  10. Connect the battery (first positive, then negative) and turn on the ignition.
  11. Perform a basic verification of functions and any configuration/programming as necessary for the vehicle.
    • 4) Post-assembly checks and test drive/function verification

      • Verify that bus communication is working and that there are no non-standard messages.
      • Check the basic comfort functions that are controlled via BSI (depending on the car’s equipment).
      • After a short test drive, verify again that everything is working stably and without dropouts.

      5) The most common assembly mistakes + how to avoid them

      • Disconnecting/connecting live connectors → always disconnect the battery and observe the idle mode.
      • Connectors interchanged or lock not clicked → mark the connectors, check the locking after connection.
      • Ignoring different codes → always compare numbers (9659285380 and others) with the old unit.
      • Fouled/oxidized contacts → check before installation and, if necessary, gently clean.

      Attention, for used engine control units and BSI comfort units, the original software of the target vehicle (EEPROM FLASH) must be loaded into the unit’s memory.

      Reasons why the part is damaged

      • Moisture and leakage into the unit space → corrosion of pins, short circuits, unstable communication.
      • Voltage fluctuations (weak battery, bad charging, bad contacts) → electronics and memory failures.
      • Unprofessional interventions (disconnecting connectors when the ignition is on, improper handling) → damage to the unit or connectors.
      • Damage to cabling/connectors in the vicinity → transition resistances, function failures and erroneous signals.
      ]]> BSI 2004 P06-00 Peugeot 207 9663798280 https://www.usedpartsvendor.com/electro-components/control-units/bsi-comfort-unit/bsi-2004-p06-00-peugeot-207-9663798280/ Sun, 19 May 2024 04:04:22 +0000 https://www.usedpartsvendor.com/uncategorized/bsi-2004-p06-00-peugeot-207-9663798280/ The BSI 2004 P06-00 Valeo Johnson Control module is designed for Citroën and Peugeot models, specifically for the Peugeot 207 from the year 2008.
      The BSI 2004 P06-00 serves as an essential Body Control Module (BCM) within your Peugeot 207. This electronic module facilitates communication between various vehicle components, including the engine control unit, lighting, and door systems.
      The part number 9663798280 is associated with the serial identification of the BSI module, while 6580PJ and 6580PK correspond to the software versions of the module. These versions are frequently updated to enhance functionality and rectify any system errors.
      The final number in the sequence, 1663372680, is linked to vehicle identification through the VIN, a unique code that allows precise vehicle identification.
      Overall, this vital module ensures the proper operation of the Peugeot 207, contributing to the vehicle’s safety and driving fluidity.

      Technical Information

      Manufacturer: Valeo Johnson Control
      Model: Peugeot 207
      Product Codes: 9663798280
      Other Numbers: 6580PJ, 6580PK, 1663372680

      ]]>             BSI 2004 P09-00 Citroën Peugeot 9659285680 6580X4 https://www.usedpartsvendor.com/electro-components/control-units/bsi-comfort-unit/bsi-2004-p09-00-citroen-peugeot-9659285680-6580x4-2/ Sat, 16 Dec 2023 05:15:26 +0000 https://www.usedpartsvendor.com/uncategorized/bsi-2004-p09-00-citroen-peugeot-9659285680-6580x4-2/ The BSI 2004 P09-00 is a vital component for Citroën and Peugeot vehicles, specifically designed for enhanced functionality and reliability. This BSI unit is compatible with popular models such as Berlingo III, C2, C3, 207, and Partner III. Its primary role is to manage various electronic features, which contribute to a seamless driving experience.

      As a critical electronic control unit (ECU), the BSI 2004 P09-00 is responsible for controlling comfort functions and vehicle settings. Failure of this unit can lead to issues such as malfunctioning lights, difficulty starting the engine, or irregular operation of central locking systems. Frequent failures may occur due to wear, exposure to moisture, or electrical faults, making timely replacement crucial for maintaining vehicle performance.

      Replacing the BSI is a straightforward process, but it requires precision. Ensure to follow the specific guidelines for the model in question. Regularly inspecting this component can prevent issues and improve vehicle reliability.

      Technical Information

      Manufacturer: Valeo Johnson Control
      Model: BSI 2004 P09-00
      Product Codes: 9659285680, 6580X4, 6580NG, 6580X5, 6580NH
      Additional Numbers: P06-00, P09-00

      ]]>