Product Overview

This is an OEM-fit right rear tail lamp designed for the PEUGEOT 3008 I (facelift) with original part number 9805510480. Built to match factory dimensions and mounting points, it provides direct replacement for damaged or non-functioning rear light assemblies. Supplied without the bulb holder, so bulbs and socket must be ordered separately when needed. Ideal for professional workshops and skilled DIYers who need a reliable, correct-fit spare part.

Function And Features

The assembly covers essential rear lighting functions depending on vehicle specification: tail lights, brake lights, turn signal/indicator and, where applicable, reversing lamp. The unit replaces the complete outer lens and housing, restoring correct light projection and road visibility. Key benefits include exact fitment to original mounting points, correct connector interface for factory wiring harnesses, and factory-style sealing to prevent moisture intrusion when installed correctly.

Compatibility

Fits: PEUGEOT 3008 I (facelift) – Right Rear (Passenger Side). Check part number 9805510480 for exact match with your vehicle variant. Commonly sought under OE code 9805510480.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 3008 I (Facelift)
• Product Codes: 9805510480
• Other Numbers: Not Available

Mounting Recommendations

Before work, disconnect the battery to avoid short circuits. Access the rear lamp from inside the tailgate or luggage compartment by removing the interior trim to reach fixing screws and wiring. Remove retaining bolts, unclip the lamp from its locating tabs, and carefully disconnect the wiring harness. Transfer any required bulbs or socket assemblies if not supplied, or install new holders as needed. Ensure the sealing gasket is correctly seated to prevent water ingress. Tighten mounting bolts to the manufacturer’s torque specifications and test all lamp functions after installation. For best results, inspect connector contacts and apply dielectric grease to prevent corrosion. Avoid touching the lens with greasy hands and do not overtighten clips or screws to prevent cracking of plastic tabs.

Why This Part Most Commonly Fails

Rear lamps typically fail due to impact damage from minor collisions, stone chips, or parking knocks. Another frequent cause is water ingress through degraded seals or cracked lenses, which leads to condensation, socket corrosion and electrical faults. Heat cycling and UV exposure can make plastic housings brittle over time, causing mounting tabs to break. Improper bulb replacement or incorrect bulb wattage can also damage sockets and wiring. Regular inspection of seals and connector condition helps prevent premature failure.

Notes For Buyers

Part Number: 9805510480. Supplied Without Bulb Holder. Recommended For Mechanics And Experienced DIYers. If the original bulb holder is missing or damaged, order the correct socket separately to ensure proper fit and function.

Order the right rear lamp 9805510480 to restore correct rear lighting and maintain vehicle safety and road legality. Designed for a direct replacement on PEUGEOT 3008 I (facelift) passenger side applications.

Description

This bulb socket is a direct-fit replacement part designed for the right rear (passenger side) tail light of the PEUGEOT 3008 first generation facelift. Supplied with a short section of wiring harness, it restores a reliable electrical connection between the bulb and the vehicle loom. Ideal for professional workshops and DIY mechanics who need a fast, cost-effective repair for a faulty tail light connector.

Benefits

• Restores secure electrical contact for tail, brake and indicator bulbs
• Supplied with wiring piece to simplify installation and avoid splicing where possible
• Durable plastic and terminal design to resist vibration and heat from bulbs
• Improves road safety by eliminating flicker and intermittent lighting faults

Technical Information

• Manufacturer: Stellantis (Citroën / PEUGEOT)
• Model: Peugeot 3008 I (Facelift) — Right Rear / Passenger Side
• Product Codes: 9805510480
• Additional Numbers: No Additional Numbers Listed

Recommended Installation

Before starting, turn off vehicle lights and allow hot bulbs to cool. Basic installation steps for an experienced mechanic or competent DIYer:

1. Remove the rear lamp assembly fasteners (usually accessible from the boot area) and carefully extract the lamp cluster.
2. Unplug the existing bulb socket from the lamp reflector. If the socket is hard-wired, cut the cable close to the socket and prepare wiring ends for reconnection.
3. Fit the new socket into the lamp reflector and connect the supplied wiring piece to the vehicle loom using appropriate connectors (insulated crimp terminals or solder and heat-shrink tubing recommended).
4. Check polarity and secure connections. Replace bulbs if worn or showing signs of overheating.
5. Reinstall the lamp assembly and verify operation of tail, brake and indicator functions before road use.

Use dielectric grease on terminals to reduce future corrosion. Avoid excessive force when inserting the socket into the lamp housing to prevent damage to plastic lugs.

Why This Part Fails

Common failure modes include:

• Corrosion of electrical contacts due to moisture ingress, causing intermittent lighting or open circuits.
• Plastic deformation or melting from excessive heat when bulbs are overpowered or mis-specified.
• Broken or brittle wiring from vibration and age, leading to loose connections.
• Poor contact caused by worn terminals or contamination from road salts and dirt.

Symptoms that indicate replacement: flickering or non-functioning rear lamps, visible burning or melting at the socket, or a loose fit between socket and bulb.

Practical Tips

• Always test the new socket with the correct specification bulb (check bulb type in vehicle manual).
• Replace both sides if the opposite socket shows similar age-related wear to ensure consistent performance.
• Secure any exposed wiring and protect joints with heat-shrink and proper routing to avoid chafing.

Safety

Work in a well-lit area and take standard electrical safety precautions. If unsure about wiring or connector techniques, have the replacement carried out by a qualified technician.