This electronic throttle pedal assembly with HELLA potentiometer is a direct-fit replacement for a range of Citroën and Peugeot drive-by-wire systems. Designed for professional workshops and competent DIY mechanics, the unit restores precise pedal feel and accurate throttle signal to the engine control unit, reducing hesitation, surging and the risk of limp-home mode. Frequently searched by product numbers, this part is commonly listed under the cross-references shown below for quick identification.

Function And Benefits

The pedal assembly contains a position sensor (potentiometer) that converts driver input into an electrical signal for the ECU. A healthy sensor ensures smooth throttle response, consistent idle and correct engine management behavior. Replacing a worn or faulty pedal typically eliminates intermittent throttle readings, engine warning lights related to pedal position, and loss of power conditions.

Installation Recommendations

Suitable for experienced technicians and skilled DIYers. Basic replacement steps:

• Disconnect the vehicle battery before starting work to avoid short circuits and protect electronic modules.
• Remove any interior trim or footwell covers to access the pedal assembly.
• Unplug the electrical connector and detach the mounting fasteners holding the pedal to the bracket.
• Fit the new pedal assembly, secure fasteners to the original points and reconnect the electrical connector. Check connector pins and wiring for corrosion or damage and repair if necessary.
• After installation clear diagnostic trouble codes. Perform a throttle adaptation or relearn procedure if required by the vehicle—some models may require a diagnostic tool to initialize the new sensor or a specified key/drive cycle.

Always follow the vehicle manufacturer service procedures and torque specifications where available.

Technical Information

• Manufacturer: HELLA
• Model: Citroën C2; Citroën C3; Citroën C3 Pluriel; Peugeot 1007; Peugeot 207; Peugeot 307; Peugeot 308
• Product Codes: 6PV009083-00; 9680756880; 9680756880-02; 9835904480; 1601T5
• Other Numbers: 1601.AW; 1601AW; 1601T5; 6PV009083-00; 9680756880; 9835904480

Most Common Failure Causes

Failures are typically due to mechanical wear of the potentiometer tracks, contamination by dirt or moisture, corrosion of connector pins, damaged wiring harnesses from footwell impact, or internal spring/return mechanism wear. Symptoms include unstable idle, delayed throttle response, intermittent engine warning lights, and activation of reduced-power mode. Life expectancy varies with use and environmental exposure; problems are more likely on high-mileage or water-exposed vehicles.

The HELLA throttle (accelerator) pedal is a direct-fit electronic pedal unit designed for a range of Citroën and Peugeot models. Built as an electronic potentiometer/drive-by-wire input, this pedal converts driver input into an accurate electrical signal for the engine management system, delivering smooth throttle response and reliable control. Supplied with OEM-style connectors and mounting points, it is commonly referenced by part numbers such as 9680756880 and 1601T5.

Features And Benefits

– Precise position sensing for consistent throttle control and improved drivability.
– Direct replacement for original equipment on compatible Citroën and Peugeot models.
– Helps resolve engine management fault codes related to pedal position sensors and drive-by-wire systems.
– Robust plastic and electronic construction designed for long service life under normal operating conditions.

Technical Information

• Manufacturer: HELLA
• Model(s): Citroën C2, Citroën C3, Citroën C3 Pluriel, Peugeot 1007, Peugeot 207, Peugeot 307
• Product Codes: 9680756880, 1601T5, 1601.AW, 1601.T5, 1601AW
• Additional Numbers: Diagnostic codes commonly associated: P0120–P0123, P0220–P0223

Function

The throttle pedal assembly contains position sensors that measure pedal travel and send a proportional electrical signal to the engine control unit. In modern drive-by-wire systems there is no mechanical cable to the throttle body—control is entirely electronic—so pedal sensor accuracy and connector reliability are critical for safe engine operation and predictable throttle response.

Installation Recommendations

– Always Disconnect The Battery Before Work To Prevent Short Circuits And Avoid Fault Codes.
– Remove Lower Dash Trim To Access The Pedal Assembly, Unplug The Electrical Connector, And Remove Retaining Bolts Or Screws.
– Install The Replacement Pedal Ensuring Correct Orientation, Secure Mounting, And That Wiring Harnesses Are Routed Without Tension.
– After Fitting, Reconnect Battery, Check For Smooth Pedal Travel And Proper Return, Clear Any Stored Fault Codes, And Perform Throttle Relearn/Adaptation If Required By The Vehicle (Using A Manufacturer-Compatible Diagnostic Tool Where Necessary).
– Tighten Fasteners To Manufacturer Specified Torque Values—If Unknown, Consult Service Manual Or Professional Technician.

Most Common Failure Reasons

– Sensor Drift Or Internal Potentiometer Wear Leading To Erratic Signals.
– Electrical Connector Corrosion Or Damaged Wiring Causing Intermittent Faults.
– Contamination From Moisture Or Debris Causing Sticking Or Loss Of Signal Integrity.
– Mechanical Damage To The Pedal Body Or Return Mechanism From Impact Or Excessive Force.
– Symptoms Often Include Check Engine Light, Reduced Engine Power (Limp Mode), Hesitation, Jerky Acceleration, Or Specific Fault Codes P0120–P0123 / P0220–P0223.

Why Replace

Faulty pedal position sensors directly affect vehicle drivability and safety. Replacing a worn or damaged pedal restores reliable throttle response, removes intermittent faults, and prevents prolonged engine management issues. For workshop professionals and experienced DIYers, this unit is a cost-effective repair when symptoms point to the pedal or its wiring.

Notes For Professionals

This pedal is intended as a direct replacement part for the listed models and part numbers. Ensure diagnostic verification after installation and perform any required calibration or adaptation procedures. If vehicle reports persistent faults after replacement, inspect wiring, grounds, and the throttle body actuator for related issues.

Technical Information:
Manufacturer: Bosch
Models: Citroën C3, Peugeot 207, 307, 308
Product Codes: 0280755084, 9680756880, 1601AW
Additional Numbers: 0280755084, 9680756880, 1601AW

This throttle pedal is designed for quick and precise response to pedal position changes, enhancing driving comfort and safety. Installation is straightforward and hassle-free, allowing for fast replacement of the old part with a high-quality component. Due to its crucial role in vehicle control and frequent use, selecting a durable and reliable replacement part is essential for long-term performance.

With this throttle pedal, you restore your vehicle’s original driving dynamics and gain confidence on every trip. Let your car come back to life with a professional-quality part from a trusted manufacturer. The pedal is carefully prepared and ready for installation.

If you are searching for quality and dependable auto parts for older Citroën and Peugeot models, take advantage of our extensive experience and wide product selection. We offer only verified components that meet the highest standards of performance and safety.