Direct-fit passenger airbag on/off switch compatible with many Stellantis passenger cars. This switch is commonly searched by part number (for example 96413912ZD, 96413912XT, 9641391277, 96373205ZD, 6556E6) and is intended for mechanics and DIY enthusiasts who need a reliable replacement that restores correct manual control of the front passenger airbag. The unit provides the expected tactile feedback and electrical connection to the vehicle SRS circuit, allowing safe deactivation when transporting a rear-facing child seat or when required by vehicle configuration. Suitable as an OEM-equivalent replacement where the original switch shows mechanical damage, contact wear, or electrical faults.

Key Benefits

– OEM-fit replacement for straightforward installation and correct dashboard alignment.
– Restores passenger airbag enable/disable functionality and dashboard indicator operation.
– Frequently searched by original part number for fast identification.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot / DS)
• Models: Citroën C3 Aircross, Citroën C3 III, Citroën C3 Picasso, Citroën C4 Picasso, Citroën C8, Peugeot 207, Peugeot 3008 I, Peugeot 308, Peugeot 308 T9, Peugeot 5008 I, Peugeot 807
• Product Codes: 96413912ZD, 96413912XT, 9641391277, 96373205ZD, 6556E6
• Additional Numbers: 6556000000, 96373205ZD, 96413912D

Installation Recommendations

• Always work with the vehicle on a stable surface and follow safe workshop practices.
• Disconnect the negative battery terminal and wait at least 10 minutes before starting work to reduce the risk of accidental airbag deployment.
• Carefully remove the relevant trim panel (usually in the dashboard or glovebox area) to access the switch. Use appropriate plastic trim tools to avoid damage.
• Unplug the electrical connector, remove the retaining screws or clips, and replace the switch with the new unit. Reconnect the connector and reassemble trim panels.
• After replacement, clear any SRS fault codes and verify correct operation of the airbag indicator and switch using an SRS-compliant diagnostic tool. If the SRS light remains on, further diagnosis of wiring and connectors is required.
• If unsure, have the replacement performed or checked by a qualified technician experienced with SRS systems.

Why This Part Fails

• Mechanical wear or broken actuator from repeated use or abuse (switch physically damaged or stuck).
• Corrosion or contamination on the electrical contacts causing intermittent or permanent loss of connectivity.
• Water ingress from leaks or cleaning that reaches the switch assembly.
• Impact damage in collisions or during dashboard removal/installation.
• Internal contact fatigue over long service life leading to unreliable switching and SRS fault codes.

Diagnosis Tips

If the passenger airbag cannot be toggled or the SRS warning lamp is illuminated, check the switch connector for corrosion and secure fit, verify continuity with a multimeter, and read SRS fault codes with a diagnostic tool to pinpoint the fault. In most cases a faulty switch will present as an SRS-related error code or as an inability to change the switch position.

Recommendation

This part is a practical, cost-effective replacement for garages and independent mechanics. Keep the original part number handy when searching or ordering to ensure correct fitment and faster delivery.

This passenger airbag switch is an OEM-style replacement designed for Citroën and Peugeot models. It allows manual deactivation of the front passenger airbag when a rear-facing child seat is fitted or when deactivation is required for safety reasons. The unit matches original fitment and reference numbers commonly used in workshops and parts lookups, making it easy to find under part codes such as 96413912XT, 96413912ZD and 6556EJ.

Designed for professional mechanics and competent DIYers, this switch restores proper functionality to the airbag on/off circuit and eliminates fault codes or warning lamps caused by a defective or worn switch. Clear fitment references and OE-style connectors reduce installation time and help ensure reliable operation once fitted.

Fits Models

• Citroën C3 Aircross
• Citroën C3 III
• Citroën C4 Picasso
• Citroën C8
• Peugeot 207
• Peugeot 3008 I
• Peugeot 308
• Peugeot 5008 I
• Peugeot 807

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Passenger Airbag Switch – Passenger Side
• Product Codes: 96413912XT, 96413912ZD, 6556EJ
• Additional Numbers: 6556EJ | 96413912XT | 96413912ZD

Installation Recommendation

Before starting any work on the SRS system, disconnect the vehicle battery (negative terminal) and wait at least two minutes to allow residual charge to dissipate from the airbag capacitors. Locate the passenger airbag switch—on affected Citroën and Peugeot models it is typically found on the passenger side of the dashboard or inside the glovebox trim. Remove the necessary interior panels, unplug the switch connector and unfasten the retaining screws or clips. Fit the new switch, reconnect the connector, reassemble trim and reconnect the battery. Finally, verify correct function by checking that the passenger airbag indicator behaves normally (no persistent airbag warning light). If an airbag warning lamp remains lit, a diagnostic scan of the SRS system may be required.

Most Common Reasons For Failure

• Mechanical Wear: Frequent use and key operation can wear contacts and the locking mechanism over time.
• Contact Corrosion: Moisture ingress or long-term exposure to humidity can corrode electrical contacts and cause intermittent or permanent failure.
• Accidental Damage: Damage during interior repairs or removal/installation of trim pieces can break switch housings or connectors.
• Electrical Faults: Wiring damage or poor connector contact can lead to false airbag fault codes or loss of switch function.
• Aging Plastics: Sunlight and heat can degrade plastic components, making the switch harder to operate or causing the key slot to fail.

This replacement is intended for mechanics and experienced DIYers who follow safety procedures for SRS systems. Using the correct part code when ordering ensures compatibility and simplifies installation in Citroën and Peugeot vehicles listed above.

This genuine-style crash/impact sensor is designed for Citroën and Peugeot vehicles and is commonly referenced by part numbers 9654903480, 96413912ZD and 8216PJ. It senses sudden deceleration and provides the trigger signal for the airbag control system and seatbelt pretensioners, helping to ensure rapid deployment of safety devices in an impact. Ideal for professional workshops and experienced DIY mechanics who search by product code when sourcing replacement parts.

Application And Compatibility

Fits selected models from Citroën and Peugeot, commonly used on Citroën C4 Picasso and Peugeot 207. Always confirm the part number against your vehicle documentation or existing part marking. This sensor is typically listed under electrical components → sensors for Stellantis vehicles.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot compatible)
• Model: Citroën C4 Picasso; Peugeot 207
• Product Codes: 9654903480; 8216PJ
• Additional Numbers: 96413912ZD

Function And Typical Location

The sensor measures rapid deceleration (impact) and sends a signal to the airbag control unit to deploy airbags and activate pyrotechnic seatbelt pretensioners. Depending on vehicle layout and model variant, the sensor may be mounted on the vehicle structure in the front crash zone or inside the passenger compartment on structural members. Exact mounting location varies by model—refer to the vehicle repair manual for the precise position.

Installation Recommendations

• Disconnect the battery before starting work and follow the vehicle manufacturer’s safety procedures.
• Locate the sensor using the vehicle service manual or the original part location, unplug the electrical connector and carefully unbolt the sensor from its mounting bracket.
• Install the replacement sensor in the same orientation as the original; incorrect orientation can prevent proper operation.
• Tighten fasteners to the manufacturer’s specified torque values and ensure connectors are clean and secure.
• After installation, perform a full diagnostic scan and clear any fault codes. Verify that the airbag warning lamp behaves normally; if the lamp remains on, consult a diagnostic tool for fault details.

Most Common Failure Reasons

• Direct damage in a previous collision—sensors are often replaced after impact because they are designed to detect and react to crashes.
• Moisture ingress or corrosion at the connector, causing intermittent or permanent electrical faults.
• Connector damage or wiring faults caused by improper repairs or vehicle modifications.
• Internal electronic failure due to age, vibration or manufacturing defects.

Replacement of the crash sensor is a safety-critical repair. If in doubt, have the job performed or checked by a qualified technician and use appropriate diagnostic equipment to confirm correct operation of the restraint system after fitting.