This right side exterior mirror is a direct-fit replacement for Citroën C4 first generation vehicles and is commonly searched under product codes 8149ZV and 1608065580. Finished in EZR Gray Aluminium paint, the mirror is electrically adjustable and includes an integrated temperature sensor. Designed for professional garages and competent DIY enthusiasts, this unit restores correct mirror positioning and functionality after damage or electrical failure.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 (First Generation) — Right Side / Passenger Door
• Product Codes: 8149ZV, 1608065580, EZRC
• Additional Numbers: Connector 7 Pins (5+2)

Function And Features

The mirror provides side and rear visibility while allowing electronic adjustment from the cabin for safe lane changes and parking. The integrated temperature sensor can be used by vehicle systems (for example climate or mirror-heating logic) and the electrical drive enables precise mirror angle control. The 7-pin connector (5+2) supplies power and signal connections required by the motor, sensor and any additional functions.

Replacement Procedure

Basic Replacement Steps (General Guidance):

• Disconnect Battery Before Work: Disconnect the negative terminal to prevent short circuits when handling electrical connectors.
• Remove Interior Door Trim Or Mirror Cover: Carefully detach the trim panel or triangular cover to access the mirror mounting screws and electrical connector.
• Unplug Connector: Locate and unplug the 7-pin connector (5+2) from the mirror module.
• Remove Mounting Bolts: Unscrew the mirror fixing bolts and remove the old mirror from the door aperture.
• Install New Mirror: Position the replacement mirror, secure the mounting bolts to the manufacturer’s torque specification, connect the wiring harness, and refit the interior trim.
• Function Test: Reconnect the battery and verify electrical adjustment, sensor function and any heating/defrosting feature if applicable.

Installation Recommendations

• Use Appropriate Tools: Torx or hex bits are commonly required for door trim and mirror fasteners — check fastener type before starting.
• Protect Door Trim: Use trim removal tools to avoid breaking clips or scratching interior surfaces.
• Check Connector Condition: Inspect pins and plugs for corrosion or bent contacts and clean if necessary before reassembly.
• Follow Manufacturer Torque And Refit Sequence: Ensure correct bolt torque and clip engagement to avoid wind noise or water ingress.

Why The Part Commonly Fails

Most Failures Are Caused By Impact Damage (Collisions Or Parking Scrapes), Water Ingress Leading To Corrosion Of Connectors Or Motor, And Wear Of The Electric Adjustment Motor After Many Years Of Use. Glass Breakage From Stones Or Vandalism Is Also Frequent. Electrical Faults May Occur From Damaged Wiring Or Moisture Entering The Connector.

Notes On Compatibility

The Part Is Intended For Citroën C4 First Generation Vehicles And Is Frequently Searched By The Codes 8149ZV And 1608065580. Verify That The Connector Type (7 Pins 5+2) And Color Match Your Vehicle When Selecting Replacement Parts.

Recommendation For Professional Service

If The Mirror Contains Additional Functions That Require Calibration Or Integration With Vehicle Systems, Consider Professional Installation. For Typical Mechanical Or Electrical Replacement, An Experienced Technician Or Confident DIYer With Basic Tools Can Perform The Swap Following The Above Steps.

Overview

This replacement right-hand exterior mirror is designed for Citroën C4 (first generation). It features an Iridis (KTC) finish and an electric adjustment mechanism with an integrated temperature sensor. The unit uses a 7-pin connector (arranged as 5+2) and fits the passenger-side door. Ideal for professional workshops and experienced DIY mechanics looking for a direct-fit, original-equivalent solution identified by part codes 8149ZV and 1608065580.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C4 First Generation (C4 I)
• Product Codes: 8149ZV, 1608065580
• Other Numbers: Color Code KTC (Iridis); Connector: 7-pin (5+2)
• Side: Right (Passenger)
• Features: Electrically Adjustable, Temperature Sensor (ambient)
• Finish: LAK Iridis (KTC)

Compatible Models

Fits Citroën C4 First Generation (approx. 2004–2010), including standard hatchback variants and facelift models where the 7-pin mirror wiring and KTC Iridis finish apply. Always verify physical connector and mounting points against the vehicle prior to installation.

Function And Purpose

The exterior mirror provides driver visibility on the passenger side with electric adjustment for quick repositioning from inside the cabin. The integrated temperature sensor supplies outside temperature information used by vehicle systems. The 7-pin connector supports the mirror motor and the sensor circuits. The Iridis paint finish ensures a color-matched appearance for vehicles painted in the corresponding KTC code.

Common Failure Reasons

• Impact Damage: Collisions or knocks are the most frequent cause of mirror breakage or housing deformation.
• Water Ingress And Corrosion: Moisture can corrode connectors or motors, causing intermittent or permanent failure.
• Motor Wear: Repeated adjustment over many years can wear the internal adjustment motor or gears.
• Connector Or Wiring Damage: Pin corrosion, bent pins or chafed wiring can interrupt signals to the mirror functions.
• Sensor Failure: Temperature sensor faults may occur due to contamination or wiring issues.

Installation Recommendations

Follow these steps for a safe and reliable replacement. Recommended for professional technicians or experienced DIYers.

1. Always Disconnect The Battery Before Starting Work To Prevent Short Circuits And Protect Vehicle Electronics.
2. Remove The Interior Door Trim Or Mirror Access Panel To Reach The Mirror Mounting Bolts.
3. Carefully Support The Mirror From The Outside While Removing Mounting Nuts To Avoid Dropping Or Damaging The Door Skin.
4. Disconnect The 7-Pin Connector And Inspect Pins For Corrosion Or Damage. Clean Contacts Or Use Dielectric Grease If Appropriate.
5. Fit The New Mirror, Reconnect The Connector, And Tighten Mounting Hardware To Manufacturer Torque Values. Replace Any Damaged Gaskets Or Foam Seals.
6. Reconnect The Battery And Test All Functions: Mirror Adjustment, Temperature Sensor Signal (check instrument cluster/vehicle diagnostics), And Any Additional Features.

After Installation: Verify Smooth Adjustment Across Full Range And Check For Unusual Noise (Indicates Gear Or Motor Issues). If The Vehicle Has Memory Or Advanced Features, Follow Manufacturer Procedures For Function Check Or Calibration.

Why Choose This Part

Direct-fit part codes (8149ZV / 1608065580) and original-equivalent finish (KTC Iridis) make this mirror a practical replacement for workshops and DIY repairs. The integrated temperature sensor and 7-pin connector ensure compatibility with the vehicle’s electrical systems when the connector and mounting match the original equipment.

Compatible with Citroën C4 models, this mirror comes in an elegant EXL metallic black color. The 7-pin configuration (5+2) guarantees a seamless connection with your vehicle’s electrical system, maintaining the high standards set by the manufacturer.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: C4
• Product Codes: 8149ZV, 1608065580
• Additional Numbers: 1608065580

Replacing the right side mirror on the Citroën C4 is essential for maintaining the vehicle’s safety and functionality. Over time, mirrors can become damaged due to weather, accidental impacts, or wear and tear, leading to decreased visibility. It is recommended to inspect mirror conditions regularly and replace them as needed to ensure a clear view of the surroundings.