This replacement left mirror is designed for mechanics and experienced DIYers who need a reliable, direct-fit solution for Peugeot 307 vehicles. The unit combines electric adjustment, heating element and power-folding for convenient operation and improved safety in cold or wet conditions. It is commonly referenced under product code 8149VV and is available in different finishes — please check the color code (LKR) to match your vehicle’s paint.

Key Features

• Driver’s Side (Left) Exterior Mirror for Peugeot 307
• Electric Adjustment for precise mirror positioning
• Integrated Heating Element to clear ice and fog
• Electric Folding Mechanism for parking protection
• Painted Finish: LKR – Babylone Red
• Connector: 7‑pin (5+2)
• Typical Professional or DIY Replacement Part Number: 8149VV

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model(s): Peugeot 307 (including 307 I)
• Product Codes: 8149VV
• Other Numbers: 7 PIN (5+2); Color Code: LKR (Babylone Red)

Installation Recommendations

• Before starting, disconnect the negative battery terminal to avoid short circuits and unintended airbag deployment.
• Remove the interior door trim or triangular mirror cover following the vehicle manufacturer’s procedure to access the mirror mounting bolts and connector.
• Carefully unplug the 7‑pin connector and compare pins to ensure full correspondence (5+2 configuration).
• Support the mirror during removal to prevent damage to the glass or paint. Remove mounting nuts, fit the new mirror, and torque fasteners to manufacturer specifications if available.
• Reconnect the electrical connector, reconnect the battery and test all functions (adjustment, heating and folding) before refitting the door trim.
• Check mirror alignment and ensure the painted finish matches surrounding panels. Replace any damaged clips or fasteners removed during disassembly.

How The Part Is Replaced

Typical replacement involves removing the interior trim piece near the mirror, disconnecting the electrical connector, unbolting the mirror from the door, and fitting the new unit in reverse order. After connection, verify mirror adjustment, heater activation and folding operation. Reassemble the door trim once correct operation is confirmed.

Why This Part Fails Most Often

• Mechanical Damage: Impact or collisions commonly crack the mirror housing or glass.
• Water Ingress And Corrosion: Moisture can corrode connectors, wiring and the small electric motors, causing failures in adjustment, heating or folding functions.
• Wear Of Internal Actuators/Gears: Repeated use can wear the plastic gears inside the folding mechanism or the adjustment motor.
• Connector Or Wiring Faults: Broken pins, loose terminals or damaged wiring in the door harness lead to intermittent or total loss of function.
• Electrical Supply Issues: Blown fuses, faulty switches or relays can appear as mirror failures but originate elsewhere in the vehicle’s electrical system.

Notes For Professionals

When replacing, ensure connector pinout and available functions (heated, folding, memory if applicable) match the vehicle specification. Test all features before completing the job to avoid return visits. For painting or color-matched units, confirm the LKR color code corresponds to the vehicle’s paint.

Keywords: Left mirror, Driver side mirror, Peugeot 307 mirror, Electric folding mirror, Heated mirror, 8149VV.

Overview

High-quality left (driver) exterior mirror designed for Peugeot 307 vehicles. This unit provides electric adjustment, integrated heating for rapid de-icing/defogging, and an electric folding mechanism for improved protection in tight parking situations. The mirror is supplied in color code KKN (Aden Red) and features a 7-pin (5+2) electrical connector. Commonly searched under product code 8149VV and reference KKNB.

Key Benefits

• Direct fit for matching Peugeot 307 models (see Technical Information).
• Electric heating speeds up demisting in cold or wet conditions.
• Electric folding reduces risk of damage when parking and improves clearance in narrow spaces.
• 7-pin connector preserves original wiring for fast replacement without splicing.
• Color-matched finish (KKN Aden Red) for a factory appearance.

How It Works

The mirror houses an electric actuator for mirror glass adjustment, a resistive heating element behind the glass to clear frost and condensation, and an electric folding motor assembly. Signals travel through the 7-pin connector (5 pins for adjustment/heater and 2 pins typically for folding or additional functions depending on vehicle wiring) to operate each function from the cabin controls.

Replacement Procedure

Recommended for experienced technicians or competent DIY mechanics. Typical replacement steps:

• Disconnect the vehicle battery to avoid short circuits and protect vehicle electronics.
• Remove the interior door trim or triangular cover to access mirror fasteners and electrical connector.
• Disconnect the 7-pin electrical connector and remove mounting nuts/bolts securing the mirror to the door.
• Remove the old mirror, fit the new unit in position and secure fasteners to the manufacturer’s torque specification.
• Reconnect the electrical connector and reconnect the battery.
• Verify full functionality: mirror adjustment, heating operation, and folding mechanism. Check for correct fit and panel alignment.

Installation Recommendations

Always follow manufacturer safety procedures. Use proper trim tools to avoid breaking door clips and take care around side airbag modules—if the vehicle is equipped with airbags, consult vehicle service literature before removing trim. Ensure connector pins are clean and undamaged; apply contact cleaner if necessary. After installation, test all mirror functions and check for noise or binding in the folding mechanism. If bodywork was repainted, verify color match (KKN Aden Red) before final assembly.

Why This Part Fails Most Often

• Impact Damage: Collisions or knocks while parking are the most frequent cause of mirror failure (broken housing, cracked glass, bent actuator).
• Water Ingress and Corrosion: Moisture can corrode electrical contacts or short motors/heaters, causing intermittent or permanent failure.
• Wear Of Folding Mechanism: Repeated folding/unfolding and mechanical stress can wear gears or motor brushes over time.
• Connector Issues: Pin corrosion or damaged wiring at the 7-pin connector can disable one or more functions.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307 (First Generation / 307 I)
• Product Codes: 8149VV, KKNB
• Other Numbers: Connector 7-pin (5+2); Color Code KKN (Aden Red)

Compatibility Notes

Designed primarily for Peugeot 307 (307 I) models. Confirm that the 7-pin connector and folding function match the original unit on the vehicle before installation. The product code 8149VV and reference KKNB are commonly used in searches for this mirror.

Final Advice

If replacing after an impact, inspect the door mounting area and wiring harness for hidden damage. For a neat cosmetic result, verify paint code KKN (Aden Red) and consider professional painting if exact color matching is required. After fitting, perform a full functional check and adjust mirror position as needed.

This replacement left (driver) exterior mirror is designed for Peugeot 307 vehicles and combines power adjustment, heating and electric folding for convenient operation and improved safety. Supplied in Obsidian Black (paint code EXL), the unit features a 7-pin connector (5+2) and is commonly referenced by product code 8149VV. Ideal for professional workshops and DIY mechanics seeking a direct-fit solution that restores mirror functions including electro-adjust, demist and power fold.

Compatibility

Designed primarily for Peugeot 307 first generation models. Common applications include hatchback and estate variants of the 307 I. Often searched by code 8149VV—use this code when locating the correct spare part.

How The Part Works And What It Replaces

The assembly contains the mirror housing, electric adjustment motor(s), heating element for glass demisting and the motorized folding mechanism. The 7-pin connector provides power and control signals for adjustment, heating and folding functions. This unit replaces damaged or non-functional left-side exterior mirrors where the original features are electric adjustment, heated glass and power-folding.

Installation Recommendations

• Disconnect the vehicle battery before beginning work to prevent short circuits and accidental deployment of electrical systems.
• Remove the interior door trim or triangular trim piece to access mirror mounting bolts and the electrical connector.
• Disconnect the mirror wiring harness and carefully unbolt the mirror from the door (retain any original nuts/bolts if reusing).
• Fit the replacement mirror, secure the mounting hardware, reconnect the wiring and reassemble the door trim.
• After installation, restore battery power and verify all functions: mirror adjustment, heating/demist and folding. Cycle functions several times to confirm correct operation.
• Use dielectric grease on electrical connectors if moisture or corrosion is suspected. Replace damaged clips, seals or fasteners to ensure a secure fit and prevent water ingress.

Why The Part Most Commonly Fails

• Impact Damage: Collisions or knocks are the most frequent cause of mirror housing, glass or folding motor damage.
• Water Ingress and Corrosion: Moisture can corrode connectors and motor contacts, leading to intermittent or permanent failure.
• Mechanical Wear: Repeated folding, especially in cold or dirty conditions, can wear gears or linkages in the folding mechanism.
• Wiring Damage: Door harnesses are exposed to flexing; broken wires or connector faults cause loss of functions.

Practical Tips For Mechanics And DIYers

• Inspect the door harness and connector pins for corrosion or broken wires before replacing the mirror.
• If only the glass or motor is faulty, check availability of individual service parts to reduce cost.
• When replacing seals or clips, use OEM-equivalent parts to maintain proper fit and prevent wind noise or water leaks.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307 (First Generation)
• Product Codes: 8149VV
• Other Numbers: EXL / EXLD; 7-Pin Connector (5+2); Color Code EXL – Obsidian Black

Upgrade your repair job with a direct-fit left (driver) side exterior mirror engineered for Peugeot 307 vehicles. This electrically adjustable, heated mirror with power folding restores full functionality and safety after damage or wear. The painted KMU Neysha Blue finish matches original factory color, making it an ideal replacement for collision repairs or aging components. Frequently searched under part code 8149VV, this unit is suitable for technicians and skilled DIYers who expect OE-style fitment and plug-and-play installation when connectors and mounts match.

Key Features

• Electrically Adjustable Mirror Glass For Accurate Rear Visibility
• Integrated Heating Element To Remove Frost And Fog
• Power Folding Mechanism For Protection When Parked
• Painted Finish KMU (Neysha Blue) For Direct Color Match
• 7-Pin (5+2) Electrical Connector Compatible With Standard Peugeot Wiring
• Direct Replacement For Driver Side (Left) On Peugeot 307 Models

Installation Recommendations

Basic steps for replacement (typical for Peugeot 307 first generation):

1. Carefully remove the interior door card using appropriate trim tools to avoid damage to clips and upholstery.
2. Disconnect the mirror’s electrical connector and any grounding wires.
3. Support the mirror and remove the mounting bolts/nuts securing it to the door.
4. Fit the replacement mirror, tighten fasteners to the manufacturer’s torque where available, and reconnect the electrical plug (7-pin configuration).
5. Reinstall the door card and test all functions: mirror adjustment, heating, and power folding.

Always disconnect the negative battery terminal before beginning work to prevent short circuits and unintended motor operation. Use plastic trim tools for interior panels to prevent scratches. If wiring appears corroded or connector pins are damaged, repair or replace wiring before final assembly.

Why This Part Commonly Fails

• Impact Damage — The most frequent cause; mirror housings and glass are vulnerable in side collisions or when struck while parked.
• Mechanical Wear — Folding mechanism and adjustment motors can wear out over time, leading to sluggish or non-functional movement.
• Water Ingress And Corrosion — Moisture can cause connector corrosion or short the heating element and motor circuits.
• Electrical Faults — Broken wires, damaged pins in the 7-pin connector, or failed heating elements are common electrical issues.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 (First Generation / 307 I) — Left Driver Side
• Product Codes: 8149VV
• Other Numbers: KMU (Paint Code Neysha Blue); 7-Pin Connector (5+2)

Advice For Professionals And DIYers

This mirror is suited for professional repair shops and experienced DIY mechanics. Verify connector pin configuration and mounting points before installation. If the original unit failed due to electrical damage or corrosion, inspect the vehicle wiring harness and replace corroded connectors to avoid premature failure of the new mirror. When in doubt about electrical diagnostics or complex door electronics, consult service documentation or a qualified technician.

This left electric folding and heated exterior mirror is a direct-fit replacement aimed at professional workshops and experienced DIY mechanics working on Peugeot 307. Designed to restore full functionality — electric adjustment, heating element and power-folding — this unit matches the original EZRC finish in Gray Aluminium and uses a 7-pin connector (5+2). Ideal for technicians searching by product code 8149VV or by the EZRC designation.

Key Features

• Electric Adjustment: Smooth motorized mirror position control for precise driver-side visibility.
• Heated Glass: Integrated heating element to speed up defrosting and improve visibility in cold conditions.
• Electric Folding: Power-folding mechanism for protection in tight spaces and automatic folding when required.
• Connector: 7-Pin Configuration (5+2) Compatible With Existing Wiring Harness.
• Finish: EZRC Gray Aluminium Paint To Match Original Exterior Trim.
• Direct Fit: Designed For Driver Side (Left) On Peugeot 307 Models.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307
• Product Codes: 8149VV
• Other Numbers: EZRC; 7-Pin (5+2); Color: Gray Aluminium Paint

Installation Recommendations

1. Disconnect Battery: For electrical safety, disconnect the negative battery terminal before beginning work.
2. Remove Interior Trim: Carefully pry off the triangular door trim to access mirror mounting bolts and the electrical connector.
3. Unfasten Mounting Bolts: Support the mirror assembly, then remove the mounting bolts holding the mirror to the door.
4. Disconnect Connector: Release the 7-pin electrical connector and any clip retainers. Inspect connector pins for corrosion or damage.
5. Install Replacement: Position new mirror, connect the electrical plug, and loosely fit mounting bolts. Check alignment, then torque bolts to manufacturer specification.
6. Test Functions: Reconnect Battery. Verify Electric Adjustment, Heating Element, And Power Folding Operation Before Reassembling Trim.
7. Reassemble Trim: Refit door trim and ensure all clips and fasteners are properly secured.

Why This Part Commonly Fails

• Motor Wear: Repeated use of adjustment and folding motors leads to mechanical wear and eventual failure.
• Water Ingress And Corrosion: Moisture can cause corrosion of internal gears, motor brushes and electrical contacts, especially at the connector.
• Impact Damage: Parking knocks or collisions frequently crack housings or damage the folding mechanism.
• Connector Faults: Bent or corroded pins in the 7-pin connector can result in intermittent or complete loss of function.
• Heater Element Failure: Over time the heating element or its wiring can degrade, reducing defrost performance.

Tips For Diagnostics And Aftercare

• Simple Tests: Check mirror motor operation by applying 12V to the adjustment motor terminals (only if you are experienced) and measure continuity of the heating element with a multimeter.
• Inspect Connector: Clean Pins And Apply Dielectric Grease To Prevent Future Corrosion.
• Lubrication: Periodically lubricate folding joints with appropriate grease to reduce wear and noise.
• Post-Installation Check: Confirm All Functions Work At Cold And Warm Engine Temperatures To Ensure Heater And Motors Operate Normally.

This replacement left mirror is an effective, original-fit solution for restoring safety and convenience features on Peugeot 307 vehicles. Searchable by code 8149VV and EZRC finish, it suits workshops and skilled DIY installers who need a reliable, plug-and-play style repair when the original mirror fails.

The product is essential for maintaining visibility while driving, especially in adverse weather. The left side mirror is crucial for ensuring safety, making it important to replace if damaged.

Technical Information

• Manufacturer: PSA Citroen Peugeot
• Model: Peugeot 307
• Product Codes: 8149VV
• Additional Numbers: N/A

This mirror is specifically designed for the driver’s side of the vehicle. It is recommended to replace the side mirrors when they become damaged or malfunctioning to maintain proper visibility on the road. Regular checks and timely replacements can prevent safety hazards and enhance the driving experience.