6580NG – Used Parts Vendor

BSI 2004 P06-00 Citroën Peugeot 9659285380

Thu, 15 Jan 2026 03:01:08 +0000

BSI 2004 P06-00 VALEO intelligent unit for CITROEN PEUGEOT cars

Part description

This BSI (Body Systems Interface) comfort unit serves as a central electronic module for controlling and communicating selected comfort and body functions of the vehicle. The offered part is marked BSI 2004 P06-00 from the manufacturer VALEO and is intended for cars of the Citroën / Peugeot concern. It is often searched and identified by product number, so we recommend that you compare all the codes from the label with the original unit when choosing.

According to the labels, the part is associated with the models: Citroën C3, Citroën C3 II, Peugeot 207.

Technical information

Manufacturer: VALEO
Model: Citroën C3 | Citroën C3 II | Peugeot 207
Other numbers: 1663372580, 6580X4, 6580NG, 6580X5, 6580NH

Product codes

Product codes: 9659285380

Installation recommendations

The exact procedure may vary according to the specific model and equipment of the car. Below is the general/typical procedure for replacing the BSI comfort unit on Citroën/Peugeot cars.

1) Before assembly

Compare all codes on the unit (especially 9659285380 and other numbers listed) to the old part.
Check for damage to connectors, connector locks and pins (bent, oxidized, pulled).
Visually verify that the unit cover is not cracked and does not show signs of moisture.

2) Necessary tools and materials

Basic set of hand tools (screwdrivers/ratchet depending on design)
Plastic pry bar for removing covers (to minimize plastic damage)
Electrical contact cleaner (optional) and dry cloth
Diagnostics / option to configure the unit (according to service equipment)

3) Step-by-step assembly procedure

Turn off the ignition, remove the key and allow the vehicle to idle for a short time (typically a few minutes).
Disconnect the battery (minus pole first) to avoid damaging the electronics.
Ensure access to the BSI unit (remove the necessary covers/panels according to the car).
Document the connection: take a picture of the connectors and their location, or mark them.
Gradually unlock the connector locks and disconnect the connectors carefully (do not pull on the cables).
Unfasten the drive and remove the drive.
Compare the old and new piece (codes, connectors, mechanical attachment).
Install the unit in place and secure it in its original mounting.
Connect the connectors in the correct order, all locks must clearly “click”.
Connect the battery (first positive, then negative) and turn on the ignition.
Perform a basic verification of functions and any configuration/programming as necessary for the vehicle.

4) Post-assembly checks and test drive/function verification
- Verify that bus communication is working and that there are no non-standard messages.
- Check the basic comfort functions that are controlled via BSI (depending on the car’s equipment).
- After a short test drive, verify again that everything is working stably and without dropouts.
5) The most common assembly mistakes + how to avoid them
- Disconnecting/connecting live connectors → always disconnect the battery and observe the idle mode.
- Connectors interchanged or lock not clicked → mark the connectors, check the locking after connection.
- Ignoring different codes → always compare numbers (9659285380 and others) with the old unit.
- Fouled/oxidized contacts → check before installation and, if necessary, gently clean.
Attention, for used engine control units and BSI comfort units, the original software of the target vehicle (EEPROM FLASH) must be loaded into the unit’s memory.

Reasons why the part is damaged
- Moisture and leakage into the unit space → corrosion of pins, short circuits, unstable communication.
- Voltage fluctuations (weak battery, bad charging, bad contacts) → electronics and memory failures.
- Unprofessional interventions (disconnecting connectors when the ignition is on, improper handling) → damage to the unit or connectors.
- Damage to cabling/connectors in the vicinity → transition resistances, function failures and erroneous signals.

BSI 2004 P10-00 Citroën Peugeot 9664156780 6580X4

Thu, 23 Nov 2023 05:11:03 +0000

The BSI 2004 P10-00 is a vital component for Citroën and Peugeot vehicles, specifically designed to enhance vehicle functionality. This unit is compatible with models such as BG III C2, C3, 207, and Partner III, offering mechanics and DIY enthusiasts a reliable solution for electronic control.

Over time, electronic control units like the BSI may fail due to wear and tear, electrical failures, or environmental factors. It is advisable to replace the BSI when experiencing issues related to vehicle control systems, ensuring smooth operation and optimal vehicle performance.

Technical Information:

Manufacturer: Valeo Johnson Control
Model: BSI 2004 P10-00
Product Codes: 9664156780, 6580X4, 6580NG, 6580X5, 6580NH
Additional Numbers: 6580NG, 6580NH, 6580X5

This BSI unit is essential for those looking to maintain or upgrade their Citroën or Peugeot vehicles, ensuring reliable control for various systems.

BSI 2004 P07-00 Citroën Peugeot 9659285480 6580NG

Thu, 23 Nov 2023 05:03:36 +0000

The BSI 2004 P07-00 is an essential component designed for Citroën and Peugeot vehicles, ensuring optimal functionality and reliability. This unit plays a crucial role in controlling various electrical systems in your vehicle, enhancing comfort and performance.

Compatible Models: This BSI unit is specifically designed for use in multiple Citroën and Peugeot models, making it a versatile choice for automotive repairs and maintenance.

Replacement Process: Replacing the BSI unit typically involves disconnecting the battery, removing the old unit from its housing, and installing the new unit. It’s recommended to consult a service manual for specific model instructions.

Common Issues: BSI units can fail due to electrical faults, water damage, or software glitches, often leading to malfunctions in vehicle systems. Regular checks can help identify problems early.

Technical Information

Manufacturer: Valeo Johnson Control

Model: BSI 2004 P07-00

Product Codes: 9659285480, 1663372580

Other Numbers: 6580NG, 6580NH