High-quality 165 mm replacement speaker designed for a wide range of Citroën and Peugeot models. This unit is a direct-fit audio component commonly sought under original part numbers and aftermarket references (see Technical Information below). Ideal for professional workshops and experienced DIY enthusiasts who need a reliable, easy-to-install speaker to restore factory sound or upgrade a worn original. The compact 165 mm size delivers clear midrange reproduction and integrates seamlessly with the vehicle’s original mounting points and wiring harness.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C2; Citroën C3; Citroën C3 Picasso; Citroën C3 Pluriel; Citroën C4 Picasso; Citroën C5; Citroën C5 X7; Citroën C8; Citroën Xsara Picasso; Peugeot 207; Peugeot 3008 I; Peugeot 308; Peugeot 407; Peugeot 5008 I; Peugeot 807
• Product Codes: 9664955880, 6562X2, 6562C5
• Other Numbers: 6562.C5, 6562.X2, 6562C5, 6562X2, 9664955880
• Size: 165 mm (6.5″) Diameter

Installation Recommendations

• Prepare Tools: Panel removal tools, Phillips/torx screwdriver set, socket set, and a multimeter for polarity check.
• Safety First: Disconnect the negative battery terminal before starting work to avoid short circuits and accidental airbag deployment when removing trim near A‑pillars.
• Remove Trim: Carefully remove the door card or trim panel following the vehicle manufacturer’s procedure to avoid breaking clips.
• Disconnect Old Speaker: Unscrew the original speaker, unplug the wiring harness, and note the polarity of the connectors or mark the positive lead.
• Fit New Speaker: Mount the replacement speaker into the original speaker aperture using the factory mounting points. Ensure the speaker sits flush and is secured without over‑tightening screws.
• Reconnect And Test: Reconnect the wiring (observe polarity), temporarily reconnect the battery, and test the speaker at low volume to confirm correct operation before reassembling the trim.
• Sealing And Vibration: Use a foam gasket or anti‑vibration pad if available to reduce rattles and improve acoustic sealing.

Why The Part Fails Most Often

• Age And Wear: Foam surrounds and suspension materials deteriorate over time, leading to distortion or rattling.
• Water Ingress: Moisture from door leaks or condensation can damage the cone, voice coil, or cause corrosion of terminals.
• Overdrive/Amplifier Faults: Excessive power or amplifier clipping can burn the voice coil, producing a blown speaker.
• Mechanical Damage: Physical impact during door repairs or improper installation can deform the cone or magnet assembly.
• Connector Corrosion Or Loose Contacts: Poor electrical connection causes intermittent sound or complete failure.

Search Tip: Many customers search by part numbers such as 9664955880, 6562X2 or 6562C5 — including these codes in your search will help you find the correct replacement quickly.

Description

This replacement 165 mm speaker is designed for a range of Citroën and Peugeot models and offers a direct-fit audio upgrade or OEM-equivalent replacement. Constructed to match original mounting points and impedance requirements, it delivers clear midrange and bass support for factory audio systems. Ideal for professional workshops and DIY mechanics who search by part number (9635014780 / 6562X2 / 6562C5) when locating the correct unit for their vehicle.

Compatibility

• Citroën C2
• Citroën C3
• Citroën C3 Pluriel
• Citroën C8
• Peugeot 3008 I
• Peugeot 307
• Peugeot 5008 I
• Peugeot 607
• Peugeot 807

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C2, Citroën C3, Citroën C3 Pluriel, Citroën C8, Peugeot 3008 I, Peugeot 307, Peugeot 5008 I, Peugeot 607, Peugeot 807
• Product Codes: 9635014780
• Other Numbers: 6562X2, 6562C5
• Diameter: 165 mm

Installation Recommendations

Remove the interior trim or door panel to access the speaker. Unscrew the speaker fasteners, carefully unplug the electrical connector, and note polarity before removing. Fit the new speaker aligning it to the original mounting holes, reconnect the connector, and secure with the original screws. Test the speaker at low volume to confirm correct operation and polarity before reassembling the trim. Use foam or rubber sealing rings and sound-deadening material where appropriate to improve bass response and reduce rattles. When working near airbags or electrical systems, take standard safety precautions and disconnect the negative battery terminal if required by your workshop procedures.

Why This Part Fails Most Often

Typical causes of speaker failure include cone or surround deterioration with age, water ingress from door seal leaks, corrosion at connectors, and voice-coil damage from excessive volume or amplifier faults. Mechanical wear and material fatigue over many years of use are common—especially in vehicles exposed to moisture or extreme temperatures. Replacement restores clarity and prevents damage to associated audio electronics caused by a failing speaker.

Practical Tips For Mechanics And DIYers

• Always verify polarity and connector fit before final assembly to avoid phase issues.
• Inspect wiring and connectors for corrosion; clean or replace as necessary.
• Consider upgrading door seals or adding damping material if you notice water ingress or rattling.
• Check the factory amplifier output if a new speaker fails quickly—electrical faults can destroy replacement speakers.

Ordering Information

Searchable by OEM code 9635014780 and cross-references 6562X2 / 6562C5. Use these numbers to quickly locate the correct speaker for the listed Citroën and Peugeot models.

This 165 mm (6.5″) replacement speaker is intended for use in a range of Citroën and Peugeot models and is commonly referenced by part numbers 9634826880, 6562X2 and 6562C5. Designed for professional workshops and experienced DIY mechanics, it provides a direct-fit replacement for factory door and rear parcel shelf speakers. The speaker restores correct acoustic balance in factory audio systems and is a straightforward swap for original equipment units when the original speaker has failed or degraded.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: See Fitment List Below
• Product Codes: 9634826880, 6562X2, 6562C5
• Additional Numbers: Diameter 165 mm (6.5″)

Fitment

Compatible with a number of Citroën and Peugeot vehicles (verify by comparing part numbers and speaker size on the original unit):

• Citroën C4
• Citroën C5
• Citroën C8
• Citroën Xsara
• Citroën Xsara Picasso
• Peugeot 207
• Peugeot 3008 I
• Peugeot 307
• Peugeot 407
• Peugeot 5008 I
• Peugeot 807

Installation Recommendation

• Disconnect the negative battery terminal before beginning work when removing interior trim components to avoid accidental short circuits and to reduce risk when working near airbags.
• Remove the door panel or parcel shelf trim carefully, retaining all clips and screws. Peel back any moisture barrier with care to avoid damage.
• Unplug the speaker connector and note polarity (positive/negative). Unscrew the original speaker and remove it from the mount.
• Fit the replacement speaker into the original location. Ensure the mounting holes and connector orientation match the factory position; use supplied adapters if necessary.
• Before full reassembly, test the speaker at low volume to confirm correct operation and polarity. Refit the moisture barrier and interior trim panels, securing all fasteners and clips.
• Use correct tools and, where needed, suitable sealing or anti-vibration materials to prevent rattles and water ingress.

Why The Part Most Often Fails

• Age-Related Wear: Foam surrounds and spider assemblies dry out and crack over time, causing distortion or loss of movement.
• Moisture Ingress: Water from leaked door seals or wet environments causes cone delamination, corrosion of terminals and short circuits.
• Overpowering: Sustained high volume or amplifier clipping can burn the voice coil or damage the cone assembly.
• Mechanical Damage: Impact or improper removal/installation can deform the cone or magnet structure.
• Connector Corrosion: Poor electrical contact due to corroded plugs or wiring corrosion reduces performance or causes intermittent sound.

Notes

Many customers search using OE part numbers (9634826880 / 6562X2 / 6562C5) — compare the code and diameter of your original speaker before ordering to ensure fitment. This unit is supplied as a direct replacement for the listed applications and is intended for professional or experienced DIY installation.