This replacement roof antenna is a direct-fit solution for Citroën C2 and C3 owners and professional workshops looking to restore reliable AM/FM reception. Supplied with the commonly referenced OEM codes, the unit is designed for straightforward installation and provides stable reception for factory and aftermarket head units. Ideal for mechanics and DIY enthusiasts who search by part number (e.g. 9653389980, 6567W7, 6561W5), this antenna brings back clear radio performance lost to physical damage, corrosion, or connector failure.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2, Citroën C3
• Product Codes: 9653389980, 6567W7, 6561W5
• Other Numbers: NFP

Function

The antenna receives terrestrial AM and FM radio signals and transmits them to the vehicle’s radio via a coaxial lead. On some vehicle configurations the antenna assembly may include a mast only; on others it can contain an amplifier module or sealed connector inside the base. Proper grounding and a tight weather seal are essential for noise‑free reception.

Common Failure Modes And Why It Fails

The antenna typically has a long service life but can fail for a few recurring reasons: corrosion at the base or connector due to water ingress, mechanical damage to the mast from car washes or impacts, broken internal cable or connector fatigue, and degraded seals that allow moisture to reach contacts. Symptoms include weak or intermittent reception, static, loss of stations, or visible damage to the antenna mast or base.

Installation Recommendations

Installation is straightforward for experienced technicians and competent DIYers. Typical steps:

• Remove The Antenna Mast By Unscrewing The External Whip Or Remove The Interior Retaining Nut Under The Headliner If Applicable.
• Protect The Headliner And Trim When Accessing The Nut; Carefully Lower The Headliner Section If Required To Reach The Fastener.
• Disconnect The Coaxial Connector From The Antenna Base; Inspect The Connector And Cable For Corrosion Or Damage.
• Fit The New Antenna, Ensure The Rubber Gasket/Seal Sits Correctly, And Tighten The Retaining Fastener Securely But Without Over‑Tightening.
• Apply A Small Amount Of Dielectric Grease To The Electrical Connector To Help Prevent Future Corrosion; Reinstall Interior Trim And Test Radio Reception.

Follow Manufacturer Repair Manual Access Procedures For Interior Trim Removal To Avoid Damage. After Replacement, Verify Reception Across Multiple Frequencies And Check For Water Tightness Around The Base.

Notes For Buyers

Many customers search using OEM part numbers, so the codes listed above are useful when confirming fitment. This antenna is aimed at Citroën C2 and C3 models; confirm model fitment by matching the referenced part numbers with the vehicle’s original equipment documentation before ordering.

Part description

We offer a used car antenna intended for the Peugeot 207. It is a part from the category of electrical components (car radio accessories) that is used to receive a radio signal. If you’re dealing with poor reception, a cracked or loose design, or damaged antenna connectors or wiring, replacing it with the correct part according to the part number is usually the fastest way back to full functionality.

When choosing, we recommend following the product codes listed below in particular – for these parts, matching the number is the surest guide.

Technical information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Peugeot 207
• Other numbers: 6561TS, 6561W

Product codes

• Product codes: 9651423580, 6561GW, 6561W5

Installation recommendations

Generally/typically applies to car antenna replacement (exact steps may vary depending on specific car design and type of antenna system).

1) Before assembly

• Check that the part codes (9651423580, 6561GW, 6561W5) and possibly other markings (6561TS, 6561W) match.
• Compare the connectors and their mechanical design with the old part (shape, securing, cable length/type, attachment).
• Inspect the part for cracks, gasket/grommet damage (if included), contact oxidation and mechanical deformation.

2) Necessary tools and materials

• Basic set of hand tools (screwdrivers/bit attachment depending on design)
• Tool for removing interior plastics/upholstery (plastic crowbar)
• Electrical contact cleaner, clean cloth
• Insulating tape or shrink tubing (depending on the condition of the cabling)

3) Step-by-step assembly procedure

1. Turn off the ignition and disconnect the battery to be safe (this is normally recommended for electrical parts).
2. Ensure access to the antenna and its wiring – remove the necessary covers/panelling so as not to break anything.
3. Disconnect the antenna connector(s) and any power supply (if included in the design).
4. Unfasten the antenna according to the specific design (nuts/screws/mount).
5. Remove the old part and check the condition of the mating surfaces, grommets and wiring.
6. Clean the contacts and the area around the mounting point; solve possible oxidation with contact cleaner.
7. Install the new antenna in its original position and seat it so that it fits properly and nothing is pinched.
8. Tighten the fastening with feeling (without pulling – there is a risk of damage to the plastics or the thread).
9. Reattach the connector(s) and check that the connector locks properly.
10. Return the removed covers/trims and check that there are no dents or scratches.
11. Connect the battery and turn on the ignition.
12. Verify radio function and reception stability.
• 4) Post-assembly checks and test drive/function verification
  • Test the reception on several stations (FM/AM depending on the equipment) and check that the reception does not change when handling the wiring.
  • After a short ride, verify that there are no signal drops and that everything is mechanically sound.

  5) The most common assembly mistakes + how to avoid them

  • Part exchange (different design/connector): always compare codes and physical design before assembly.
  • Unsnap connector: after connecting, gently pull on the connector to verify the lock.
  • Pinched wiring when installing the trim: run the cables in the same route as originally and check the passages.
  • Oxidation of contacts: clean the connectors and use contact cleaner if needed.

  Reasons why the part is damaged

  • Mechanical damage (impact, vandalism, caught during washing/parking).
  • Influence of weather – aging of plastics and seals, penetration of moisture and subsequent corrosion of contacts.
  • Loose mounting and vibrations that gradually damage the cable or connector.
  • Unprofessional disassembly – torn cable, damaged connector locks or cracked covers.
  ]]> https://www.usedpartsvendor.com/electro-components/car-radios-and-accessories/autoanteny/antenna-citroen-peugeot-9655613780-6561z9-6561w5-3/ Wed, 07 Jan 2026 03:03:10 +0000 https://www.usedpartsvendor.com/uncategorized/antenna-citroen-peugeot-9655613780-6561z9-6561w5-3/ Antenna for CITROËN C4, C5, C8 and PEUGEOT 308, 807 and others.

  This genuine-style roof antenna is a direct-fit replacement for many Citroën and Peugeot models and is commonly searched by OE numbers 9655613780, 6561Z9 and 6561W5. Designed to restore reliable AM/FM reception and to interface with vehicle-specific aerial feeds, it is suitable for workshop fitment or competent DIY replacement. Clear, searchable product codes and model fitment make this part ideal for mechanics and enthusiasts looking to quickly identify the correct antenna assembly.

  Technical Information

  • Manufacturer: Stellantis
  • Model: Citroën C4, Citroën C5, Citroën C8, Peugeot 308, Peugeot 807
  • Product Codes: 9655613780, 6561Z9, 6561W5
  • Other Numbers: 6561W5, 6561Z9, 9655613780 (common references)

  Function and Compatibility

  The antenna provides the vehicle with external radio reception and, depending on the vehicle equipment, may carry additional aerial feeds for telematic or navigation modules. Compatibility is determined by the antenna base and connector type; the listed OE codes are the fastest way to confirm a match for the vehicle.

  Replacement Procedure

  1. Park the vehicle on a level surface and isolate electrical loads where necessary. For safety, disable accessories as required by your workshop procedures.
  2. Remove any interior trim or roof lining access panels covering the antenna base — typically located above the headliner near the roof centre or rear roof area, depending on model.
  3. Unscrew the antenna mast or remove the antenna cover to access the mounting nut and the coaxial connector. Retain any sealing gaskets if reusable.
  4. Disconnect the coaxial cable and any additional wiring harness from the antenna base. Inspect connectors and wiring for corrosion or damage.
  5. Unscrew the mounting nut and remove the antenna assembly from the roof. Clean the mounting area and replace seals if necessary to maintain watertightness.
  6. Fit the new antenna, reconnect cables, secure the mounting nut to the correct torque, and reinstall interior trim. Test radio reception and any dependent systems before returning the vehicle to service.

  Installation Recommendations

  • Use correct torque values for the mounting nut to ensure sealing and proper grounding of the antenna mast.
  • Replace weather seals or gaskets to prevent water ingress; a compromised seal is a common source of failure.
  • Check and, if necessary, clean coaxial connectors and earth points to avoid reception issues caused by poor connections or corrosion.
  • When reinstalling headliner or trim, ensure wiring is routed without sharp bends or pinching to prevent future cable damage.
  • After replacement, verify AM/FM reception across multiple stations and confirm any integrated systems (e.g., hands-free or navigation antennas) are functioning if applicable.

  Most Common Failure Causes

  • Mechanical damage to the mast or base from car washes, vandalism or impacts.
  • Water ingress and corrosion at the base or connectors leading to poor continuity or short circuits.
  • Worn or broken coaxial cable and connector fatigue from years of movement and vibration.
  • Poor grounding or loose mounting causing intermittent reception or noise.

  Searchable OE numbers 9655613780, 6561Z9 and 6561W5 help locate the correct antenna quickly. Suitable for professional garages and experienced DIYers familiar with roof trim removal and basic vehicle electrical checks.

  ]]> https://www.usedpartsvendor.com/electro-components/car-radios-and-accessories/autoanteny/antenna-citroen-peugeot-9655613780-6561z9/ Wed, 07 Jan 2026 03:01:48 +0000 https://www.usedpartsvendor.com/uncategorized/antenna-citroen-peugeot-9655613780-6561z9/ Antenna for CITROËN C4, C5, C8 and PEUGEOT 308 and others

  This high-quality replacement antenna is designed for Citroën and Peugeot vehicles and matches common OEM references used by Stellantis. Ideal for professional workshops and DIY mechanics, the antenna restores reliable radio reception and fits as a direct replacement for the listed models. The part is often searched by its product codes, so finding the correct reference (9655613780 / 6561Z9 / 6561W5) speeds up procurement and installation.

  Benefits include straightforward fitment, robust weather-resistant construction, and compatibility with factory mounts and cabling in the specified vehicles. The antenna restores AM/FM reception performance and integrates with vehicles that use an external aerial mast or roof-mounted antenna base. It is a practical spare part for routine repairs after mechanical damage or signal degradation.

  Technical Information

  • Manufacturer: Stellantis (Citroën / Peugeot)
  • Model: Citroën C4, Citroën C5, Citroën C8, Peugeot 308, Peugeot 807
  • Product Codes: 9655613780, 6561Z9, 6561W5
  • Other Numbers: 6587J0

  Installation Recommendations

  Fitment is generally straightforward for experienced technicians. Typical installation steps:

  • Park the vehicle on a level surface and disconnect the negative battery terminal to avoid short circuits while working on electrical components.
  • Remove any interior trim or headliner sections required to access the antenna mounting nut from inside the roof or remove the external protection cap if applicable.
  • Unscrew the retaining nut and carefully disconnect the antenna coaxial cable and any power plug for an integrated amplifier.
  • Install the new antenna, ensure the sealing gasket is correctly positioned to prevent water ingress, reconnect the cable and any power connector, then torque the retaining nut to the manufacturer’s specification.
  • Reassemble trim/headliner, reconnect the battery, and verify radio reception and any amplified reception function. Adjust seating to ensure watertight fit.

  Why This Part Fails

  • Mechanical Damage: Impact, theft attempts, or hammering during car washes can bend or break the mast or base.
  • Corrosion and Water Ingress: Seals and connectors can corrode over time, degrading electrical contact and allowing water into the base.
  • Cable Or Connector Faults: Damaged coaxial cable or corroded connectors reduce signal quality or interrupt antenna power for amplified systems.
  • Amplifier Failure: Some antennas include a small amplifier; age or moisture can cause the amplifier to fail, resulting in poor reception.

  Practical Tips

  • Always Compare Product Codes: Match the codes printed on your old antenna with the numbers listed above to ensure correct fitment.
  • Check Sealing During Reassembly: Proper sealing prevents future water-related failures.
  • Inspect Coaxial Cable Condition: Replace or reseat damaged cables and connectors to restore optimum reception.

  Order this antenna if your vehicle displays weak or intermittent radio reception, visible antenna damage, or if the mounting/base shows signs of corrosion. The referenced product codes (9655613780, 6561Z9, 6561W5) are commonly used identifiers for this part and will help you confirm fitment quickly.

  ]]> https://www.usedpartsvendor.com/electro-components/car-radios-and-accessories/307-i-car-radios-and-accessories/antenna-citroen-peugeot-9650911180-6561y1-2/ Mon, 24 Nov 2025 03:04:24 +0000 https://www.usedpartsvendor.com/uncategorized/antenna-citroen-peugeot-9650911180-6561y1-2/ Antenna for Citroën and Peugeot Vehicles with Mast.

  High-quality roof mast antenna designed as a direct-fit replacement for a range of Citroën and Peugeot models. Ideal for professional garages and DIY mechanics, this antenna restores reliable AM/FM reception and matches original equipment part numbers 9650911180, 6561Y1, 6561A0 and 6561W5. The rugged rod design ensures stable reception and straightforward installation, making it a practical choice when the original mast is damaged, corroded or suffering from poor signal.

  Features

  • Rod-Type Mast: Simple, robust design for consistent radio reception.
  • OEM Part Number Compatibility: Fits vehicles using part numbers 9650911180, 6561Y1, 6561A0, 6561W5.
  • Easy Replacement: Designed for direct swap with factory mounting points and coax connector.
  • Professional and DIY Friendly: Suitable for automechanics and experienced home mechanics.

  Technical Information

  • Manufacturer: Stellantis / Citroën / Peugeot
  • Model: Citroën C5; Peugeot 307 (I / II); Peugeot 407
  • Product Codes: 9650911180, 6561Y1, 6561A0, 6561W5
  • Additional Numbers: 6561A0 | 6561W5 | 6561Y1 | 9650911180

  Installation Recommendations

  Remove the old mast by unscrewing it from the base and disconnecting the coaxial cable at the connector or under the trim. Inspect the antenna base, sealing gasket and surrounding roof area for corrosion or damage. Clean the mating surfaces and replace worn gaskets to ensure a watertight fit. Screw the new mast into the base by hand and then secure to a snug fit—avoid excessive torque to prevent thread or base damage. Reconnect the coaxial connector and test AM/FM reception and radio operation before reassembling any removed trim. Use basic hand tools; professional fitment is quick for an experienced technician.

  Why This Part Most Often Fails

  • Mechanical Damage: Mast bending or breaking from car washes, low-clearance obstacles or vandalism.
  • Corrosion And Water Ingress: Salt and moisture lead to base corrosion or poor electrical contact.
  • Connector Wear: Oxidation or loose coax connection causing intermittent reception or signal loss.
  • Aging Materials: Rubber seals and gaskets harden over time, allowing moisture entry and electrical issues.

  Fitment And Notes

  This antenna is commonly fitted to Citroën C5 and Peugeot 307 / 407 applications using the listed OEM numbers. Customers frequently search by part number in repair shops and online catalogues, so listing the original codes helps find the correct replacement quickly. Always verify physical match (mounting type and connector) when replacing an aftermarket or non-original antenna.

  Order this antenna mast to restore reliable radio reception and maintain the vehicle’s original appearance and function. Suitable for routine replacement during bodywork or when reception degrades due to damage or corrosion.

  ]]> https://www.usedpartsvendor.com/electro-components/car-radios-and-accessories/307-ii-car-radios-and-accessories/antenna-peugeot-207-9665549680-6561ts-2/ Sat, 12 Jul 2025 02:03:28 +0000 https://www.usedpartsvendor.com/uncategorized/antenna-peugeot-207-9665549680-6561ts-2/ Product Overview

  This antenna is designed specifically for Peugeot 207 and 207 II models, offering a reliable replacement option for damaged or malfunctioning original equipment. With product codes 9665549680 and 6561TS, it guarantees compatibility and maintains the performance of your vehicle’s radio system.

  Essential for clear radio signal reception, the antenna is commonly replaced due to damage caused by car washes or accidental mishandling. Installation is straightforward and can be completed at home with minimal tools, saving you service costs while restoring optimal radio performance.

  Technical Information

  Manufacturer: PSA Citroën Peugeot
  Models: Peugeot 207, 207 II
  Product Codes: 9665549680, 6561TS, 6561W5
  Additional Numbers: Not Specified

  This genuine part ensures long-term durability and dependable functionality, making it a smart choice for automechanics and car enthusiasts performing their own repairs. Confirming compatibility with your vehicle model will help ensure seamless operation of your car radio and related components.

  Restore your antenna to perfect working condition and enjoy uninterrupted listening to your favorite radio stations. Order now to benefit from competitive pricing and fast shipping!

  ]]>