Peugeot 207 passenger seat harness 6545GC is an original electrical wiring harness designed for the connection and function of the passenger seat in Peugeot 207 cars of the first series. It enables the correct connection of all necessary components in the seat – typically the occupancy sensor, possible side airbags, seat belt tensioners or other electrical elements depending on the specific equipment of the car. This helps ensure the full functionality of the seat’s safety and comfort systems as designed by the manufacturer.

Manufacturer: PSA Peugeot Citroën
Model: Peugeot 207 (first series)
Location: Passenger seat harness
Category: Electrical components – cable harnesses – others

Product codes: 6545GC
Other numbers: they may vary depending on the equipment version and production series, so it is important to compare the markings, the shape of the connectors and the length of the harness with the original part from the car.

This bundle is suitable for anyone who needs to replace damaged under-seat wiring – whether due to mechanical damage, corrosion of contacts, non-professional intervention or retrofitting. A properly functioning wiring harness is especially crucial for airbag and safety systems, where a faulty signal can cause the airbag light to illuminate, error messages on the on-board computer, or safety features to fail in an accident.

Technical information and features:
– Original harness type for passenger seat Peugeot 207 first series
– Precisely shaped connectors for connecting to the original installation of the car
– Cable routing in protective tubes and bundles according to the original solution
– Designed for used Peugeot 207 vehicles – an ideal replacement for a damaged or non-functioning original harness
– Often searched under catalog number 6545GC or its internal variants

Advantages of using the original passenger seat harness:
– Exact compatibility with Peugeot 207 first series wiring
– Correct function of the sensors, airbag and belt tensioners according to the car’s equipment
– Minimal risk of errors, flashing lights and MOT problems caused by improper wiring
– There is no need to modify connectors or cabling, everything fits into the original installation

Installation recommendations:
– Before any manipulation, always disconnect the battery and observe the safety break (especially for the airbag system).
– Disassemble the seat according to the manufacturer’s service procedure and ensure sufficient access to the wiring under the seat.
– Remove the original bundle only after carefully marking or memorizing the cable routing and the position of the individual connectors.
– Guide the new harness along the same route as the original to avoid pinching, chafing or stretching when the seat is moved.
– Check that all connectors are fully engaged and securely snapped into the holders so they do not come loose while driving.
– After completing the assembly, connect the battery, erase any error codes in the control unit and verify the function of the airbag and safety systems by diagnosing and checking the lights on the instrument panel.

A correctly selected and professionally installed Peugeot 207 6545GC passenger seat harness helps to restore the full functionality of the electrical and safety installation of the seat and ensures long-term reliable operation of the car.

The Peugeot 207 6545GC driver’s seat harness is an original wiring harness designed for the first series of the Peugeot 207 model. This is a harness specifically for the driver’s seat, so it is important not to confuse it with the harness for the passenger seat. Thanks to the correct harness, all electrical functions of the seat work as they should – e.g. occupancy sensors, possible heating, airbags in the seat or other electrical elements depending on the car’s equipment.

This part is suitable for Peugeot 207 owners and car mechanics who need to solve faults in the electrical installation of the driver’s seat, such as airbag faults, a malfunctioning sensor or broken wires. A used original harness is often cheaper than a new part and at the same time maintains proper compatibility with the car’s original wiring.

Technical information:
Manufacturer: PSA Citroën Peugeot
Model: Peugeot 207 (first series)
Location: driver’s seat
Product codes: 6545GC
Additional numbers: may vary by trim level and year of manufacture, often include PSA internal numbering and sub-variant designations for specific vehicle trim

Advantages of using the original Peugeot 207 6545GC driver’s seat harness:
– maintenance of the correct function of airbags and safety elements in the seat
– compatibility with the car’s original wiring
– minimization of error messages on the dashboard
– quality processing according to PSA standards

Installation recommendations:
Before removing the old harness, always disconnect the battery and wait a few minutes to discharge the residual charges in the airbag system. Pull the seat out carefully so as not to damage other wiring or connectors in the floor. When installing a new harness, carefully check all connectors to make sure they are fully engaged and not mechanically damaged. Run the wires along the same routes as the original bundle, use the original grips and clips to protect the wiring from pinching and abrasion. After installation is complete, connect the battery, perform a basic seat function check, and check the dashboard for an airbag light or other error message. For a professional result, it is advisable to read and possibly delete the error codes of the control unit with diagnostics after replacing the bundle.

The Peugeot 207 driver’s seat harness 6545GC is an original wiring harness intended for the first series of the Peugeot 207 model. It is exclusively a harness for the driver’s seat, therefore it cannot be confused with a harness for the passenger seat – they differ in connection and wire lengths. Correct bundling is essential for the trouble-free operation of all electrical elements in the seat, such as occupancy sensors, seat heating if necessary, side airbags in the backrest and other elements depending on the specific equipment of the car.

This used original part is suitable for car mechanics as well as for home repairs if you are dealing with faults in the electrical installation of the driver’s seat, typically airbag error messages, a non-functioning occupancy sensor or mechanically damaged wiring (twisted or broken wires, loose connectors). The original Peugeot 207 6545GC driver’s seat harness helps to maintain correct compatibility with the original installation and reduces the risk of malfunctioning circuits or frequent error messages on the dashboard.

Technical information:
Manufacturer: PSA Citroën Peugeot
Model: Peugeot 207 (first series)
Location: driver’s seat
Product codes: 6545GC
Other numbers: internal and sub-variant PSA designation according to specific equipment, year of manufacture and type of seat (e.g. presence of heating, side airbags, occupancy sensors, etc.)

Advantages of using the original Peugeot 207 6545GC driver’s seat harness:
– proper function of airbags and safety elements in the seat
– full compatibility with the car’s original wiring
– minimization of error messages and emergency modes of the airbag system
– quality materials and processing according to PSA standards

Installation recommendations:
Before starting work, always disconnect the battery and wait a few minutes for the remaining charges in the airbag system to discharge. Remove the seat from the car carefully to avoid damaging the floor wiring or connectors. When removing the old harness, make a note or photograph of the original wire routing and location of the lugs – this will facilitate correct installation of the new harness.

Route the new Peugeot 207 6545GC driver’s seat harness in the same way as the original, using the original mounts, clips and grommets so that the wiring is not subject to pinching, pulling or chafing when the seat moves. Plug in all the connectors as far as they will go, check the latches and any connector fuses. After completing the assembly, reattach the seat, tighten the screws according to the manufacturer’s recommended torques, and only then connect the battery. Subsequently, check the functions of the seat (advancement, possible heating, presence of airbag error lights). For a professional result, it is advisable to read and clear any error codes in the control unit using diagnostics after the replacement.