Product Overview

This original Citroën bulb holder with a short length of cable is designed for the right rear tail light of the Citroën Xsara Picasso (models up to 2004). It secures the bulbs in the lamp cluster and provides the electrical connection for brake, tail and indicator lights. The part is often searched by its product numbers, so we list all known references below for quick identification.

Key Benefits

• Direct fit for the right rear lamp assembly on Citroën Xsara Picasso (pre-2004).
• Original Citroën quality—correct connector shape and mounting points for plug-and-play replacement.
• Includes a short piece of cable for easier handling during installation.
• Useful for mechanics and DIY enthusiasts who search by part number.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën Xsara Picasso (up to 2004)
• Product Codes: 6351N0, 6351T2
• Additional Numbers: 9631563980, 6351.N0, 6351.T2

Function And Fitment

The holder secures rear light bulbs in their sockets and provides the conductive contact between bulb and vehicle wiring. It is fitted into the right-hand rear lamp cluster, located behind the passenger-side trim panel in the luggage area. Proper seating of the holder ensures reliable contact and prevents intermittent lighting faults.

Common Failure Causes

Typical reasons for replacement include:

• Corrosion Of Contacts: Moisture ingress causes oxidation of terminals, leading to poor contact or intermittent lights.
• Mechanical Damage: Repeated bulb changes, impact or rough handling can crack the plastic housing or deform contacts.
• Heat Deformation: High temperatures from bulbs or poor ventilation may warp the socket and reduce contact pressure.
• Wiring Fatigue Or Breakage: Movement near the mounting point can wear the cable or break strands at the crimp.

How To Replace

1. Access The Lamp: Remove the rear trim panel or access cover behind the passenger-side seating area to reach the lamp cluster.
2. Remove The Lamp Assembly Or Socket: Depending on the vehicle trim, either remove the lamp assembly fasteners or reach the socket from inside and twist/pull the holder out of the cluster.
3. Disconnect Wiring: Carefully unplug the wiring connector or cut if required and prepare the new holder’s cable for connection. Ensure correct polarity and secure crimp/solder joints where used.
4. Fit The New Holder: Insert and lock the new holder into the lamp cluster until it seats firmly. Reinstall the lamp assembly and trim panels.
5. Test All Light Functions: Verify tail, brake and indicator functions before finishing. Replace bulbs with the correct types if necessary.

Installation Recommendations

• Disconnect The Battery: For safety and to avoid short circuits, disconnect the negative battery terminal before starting work.
• Use Dielectric Grease: Apply a small amount of dielectric grease to contacts to reduce future corrosion and improve longevity.
• Check Bulb Condition: Bulbs Are Not Guaranteed With The Part; Inspect Or Replace Bulbs During Installation To Avoid Repeat Visits.
• Secure Connections: Use Proper Crimps Or Solder Joints And Insulate With Heat-Shrink Tubing To Prevent Water Ingress.
• Verify Fitment: Ensure The Holder Locks Into Place And That The Cable Is Routed Free From Moving Parts.

Why This Part Is Useful For Mechanics And DIYers

Part numbers are included for quick lookup and ordering, saving workshop time. Replacing a worn or corroded bulb holder restores reliable lighting operation and eliminates intermittent faults that can lead to failed inspections or safety issues. The original Citroën design ensures correct mechanical fit and connector alignment.

Ordering Notes

Search Using The Product Codes Above For Fast Identification. The Part Is Supplied As Shown; Bulbs May Or May Not Be Included And Their Function Is Not Guaranteed.

Why Parts Fail Most Often

In this application the most frequent cause of failure is moisture ingress leading to corroded contacts, often combined with age-related embrittlement of the plastic housing. Regular inspection of rear lamp seals and prompt replacement of cracked sockets will prevent most electrical faults.

This replacement rear-right lamp bulb holder is suitable for Citroën Xsara Picasso and is referenced under OE codes 9631563980, 6351N0 and 6351T2. Designed for mechanics and DIY car owners, the part restores secure electrical contact for tail/stop/indicator bulbs, helping to eliminate flicker and intermittent lighting caused by worn or corroded contacts. The unit is a direct-fit socket for the passenger-side rear light and is ideal when the existing holder shows signs of contact failure or physical damage.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën Xsara Picasso
• Product Codes: 6351N0, 6351T2, 9631563980
• Other Numbers: 6351N0 | 6351T2 | 9631563980

Fitment

Fits: Rear Right Lamp (Passenger Side) on Citroën Xsara Picasso. Check the shape and connector of the original socket to confirm visual match with your vehicle’s tail lamp assembly.

Installation Recommendations

• Before starting, switch off ignition and lights; for additional safety disconnect the negative battery terminal.
• Access the rear lamp cluster from the boot/boot panel: remove trim and the lamp fixing screws or nuts.
• Withdraw the lamp assembly and press the bulb-socket retaining tabs to remove the old socket.
• Unplug any wiring harness clips if present and replace with the new socket, ensuring secure engagement of contacts and correct bulb orientation.
• Refit the lamp assembly, check bulb seating, reconnect the battery and test all functions (tail, stop, indicator, reverse where applicable) before reassembling interior trim.
• Use correct replacement bulbs and avoid excessive wattage to prevent overheating of the socket.

Why The Part Most Commonly Fails

• Corrosion and Moisture Ingress: Water entering the lamp housing causes oxidation of contacts and poor conductivity.
• Heat Damage: Repeated heating from bulbs or over-wattage bulbs can deform plastic and degrade contacts.
• Mechanical Wear: Repeated bulb changes and vibration can loosen or fracture contact terminals and retaining tabs.
• Poor Electrical Contact: Dirt, loose connectors or bent pins cause intermittent operation and flickering lights.

Practical Tips

• When replacing the socket, inspect the lamp housing for cracks or seals that could allow water ingress and replace or reseal as needed.
• Test each lamp function after installation and verify good contact under vibration by gently moving the assembly while lights are on.
• Keep the OE product codes (6351N0, 6351T2, 9631563980) handy when searching for matching parts to improve findability and ensure correct fitment.

Are you looking for a reliable and high-quality replacement part for your Citroën Xsara Picasso? Our offering includes the right rear light, which is an ideal choice for models from 2004. This part provides not only functionality but also enhances the aesthetic appearance of your vehicle. The light is located on the passenger side and comes without a bulb holder, which can be purchased separately based on your vehicle’s needs.

In our offer, we focus on providing spare parts that meet high-quality standards while remaining competitively priced. This way, you can be sure that you are investing in a product that will contribute to the long-term reliability and safety of your vehicle.

Technical Information:
Manufacturer: Citroën
Model: Xsara Picasso
Product Codes: 9650005780, 89032868, 6351T2
Other Numbers: The lamp does not have any additional specific numbers or references, and replacement requires standard technical skills and tools.

This right rear light is designed to match the original specifications and design of the Citroën Xsara Picasso vehicle, ensuring proper lighting functionality and contributing to the overall aesthetic of the vehicle. Replacing the light is relatively straightforward, allowing for easy installation for both professional shops and DIY enthusiasts. However, it is recommended that installation be performed by a professional to avoid potential complications and to ensure maximum safety and functionality.

When selecting spare parts, it is important to pay attention to quality and compatibility. This light is specifically made for Xsara Picasso models starting from 2004 and is a great choice for restoring the original functions and design of your vehicle. The combination of quality materials, precise workmanship, and faithful reproduction of the original design ensures that this product will meet your expectations and needs.

For more information or to purchase this light, visit our online e-shop, where you can easily select other necessary parts for your car. With a wide range and clear layout of our website, you will find everything you need quickly and efficiently.

Thanks to its location on the passenger side, this light can improve your vehicle’s visibility and ensure your safety during nighttime driving or adverse weather conditions. Its replacement is relatively simple and quick, which will be appreciated by any DIY enthusiast or professional mechanic. This part is commonly replaced due to damage caused by accidents or wear.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: Citroën Xsara Picasso, from 2004
• Product Codes: 9650005780, 89032868, 6351T2
• Other Numbers: No other specific numbers

This headlamp is an excellent choice for anyone looking for a reliable and cost-effective replacement part for the Citroën Xsara Picasso. Don’t waste time searching for parts of uncertain quality; choose our proven product that offers both quality and great value for money. Make sure your vehicle is equipped with the best the market has to offer without overspending.

Don’t forget to add this product to your shopping cart and continue upgrading your Citroën Xsara Picasso with our quality auto parts. With a wide range of replacement headlights and other parts, you’re sure to find exactly what you need for your car. Order today and enjoy driving a fully functional vehicle again!