This genuine-fit right rear taillight is designed for Peugeot 206 Combi models and provides a direct replacement for damaged or broken rear lamps. The unit restores proper brake, tail and indicator light functions, improves vehicle safety and ensures compliance with road visibility standards. Ideal for professional workshops and experienced DIY mechanics who need a reliable, OEM-compatible taillight with known part references (9641540577 / 6351R4).

Fitment And Compatibility

Fits: Peugeot 206 Combi (estate) models. Commonly referenced by part numbers 9641540577 and 6351R4. Verify the lamp shape and mounting points against the vehicle before installation. Note: This item is supplied without the bulb holder/socket—purchase the holder and bulbs separately under code 6351R4 if required.

How It Works

The taillight assembly houses the brake light, tail light and turn signal lenses and directs emitted light through reflectors to maximise visibility. The lamp transfers electrical signals from the vehicle harness to the bulbs via a bulb holder/socket (not included). Proper sealing and secure mounting keep the electrical connections dry and stable to maintain reliable operation.

Replacement Procedure (Overview)

• Open the tailgate and remove the interior trim or access panel to reach the lamp retaining screws.
• Unscrew the retaining bolts or nuts holding the lamp assembly; support the lamp to avoid dropping it.
• Carefully pull the lamp outward and disconnect the wiring connector or remove the bulb holder (if present).
• Install the new lamp assembly, reconnect the wiring or fit the bulb holder (purchased separately), and secure all fasteners.
• Test all light functions (tail, brake, indicator, reverse if applicable) before reassembling the interior trim.

Recommended Installation

Perform installation in a dry, well-lit area. Inspect the mounting gaskets and replace any damaged seals to prevent moisture ingress. Check the vehicle wiring and connector for corrosion or damage and repair as needed. Tighten fasteners to the original torque specification where available. For electrical work, use proper insulated tools and ensure good connector engagement. After fitting, verify correct operation of all lamp functions.

Why Taillights Fail

Common causes of failure include physical impact (cracks or broken mounting tabs), water ingress due to degraded seals, connector corrosion, and heat or vibration causing internal damage. In some cases the bulb holder or wiring harness fails while the outer lens looks intact—remember this assembly is supplied without the bulb holder, so check the socket condition when replacing the lamp.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 206 Combi
• Product Codes: 9641540577, 6351R4
• Additional Numbers: 6351R4
• Notes: Supplied Without Bulb Holder/Socket. Bulb Holder And Wiring Can Be Ordered Separately Under Code 6351R4.

Tips For Professionals And DIYers

• Carry spare gaskets and appropriate fasteners when replacing taillights to ensure a watertight fitment.
• If the original lamp failed from moisture, inspect and clean the harness connector and apply dielectric grease to prevent future corrosion.
• When replacing bulbs, use the specified bulb types and avoid touching halogen bulbs with bare hands.

Part numbers and visual fitment references (9641540577 / 6351R4) are commonly used when searching for the correct replacement lamp—include these in searches to improve findability.

This right rear tail lamp socket with attached wiring harness is a practical replacement for Peugeot 206 Combi owners and professionals. Designed to restore reliable electrical connection to the tail, brake and indicator bulbs, this unit simplifies lamp repairs by delivering a ready-to-fit connector and a short section of cable that mates directly with the vehicle harness.

Description and Function

The part provides the electrical interface between the vehicle wiring and the lamp bulbs mounted in the right rear tail light assembly. It secures the bulbs, holds the electrical contacts, and routes the signals for tail, stop and turn functions. Proper contact and insulation are essential to avoid flicker, intermittent failure or short circuits.

Compatibility

Direct fit for:

• Peugeot 206 Combi — Right Rear Tail Light Assembly

Often searched by product code 6351R4. Verify visual match with your original connector and pin layout before installation.

Installation

Typical replacement steps for a workshop or experienced DIY mechanic:

1. Park the vehicle on a level surface, switch off ignition and, as a safety precaution, disconnect the negative battery terminal.
2. Open the tailgate and remove interior trim panels or access covers to reach the tail lamp assembly.
3. Unscrew or unclip the lamp assembly and carefully pull it out to expose the bulb holder/socket.
4. Unplug the old socket from the lamp cluster and release any retaining clips or ties on the wiring.
5. Fit the new socket with wiring: insert bulbs, connect the socket to the lamp cluster and secure wiring to avoid rubbing or pinching.
6. Reconnect the battery, test all light functions (tail, brake, indicator, reverse if applicable) before reassembling trim.
7. Reinstall trim and ensure watertight seals around the lamp to prevent future moisture ingress.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 206 Combi
• Product Codes: 6351R4
• Additional Numbers: None specified

Installation Recommendations

• Always disconnect the battery before starting work to avoid short circuits and accidental bulb activation.
• Check bulb condition and replace any worn or discolored bulbs when fitting the socket to ensure balanced light output.
• Apply a small amount of dielectric grease to the connector pins to improve contact and reduce corrosion risk.
• Ensure wiring is routed away from sharp edges and heat sources; secure with cable ties and restore any sealing grommets to keep moisture out.
• Test all functions before final reassembly and ensure the lamp housing closes correctly to maintain a watertight seal.

Why This Part Fails Most Often

• Corrosion of connector pins due to water ingress or damaged seals, causing intermittent or no contact.
• Heat damage from overloaded bulbs or poor ventilation in the lamp assembly leading to deformation of the socket.
• Mechanical fatigue from vibration, repeated bulb changes or improper installation causing broken wires or cracked plastic.
• Short circuits from damaged insulation or pin misalignment resulting in blown fuses or burned contacts.

Condition Note: The connector and socket on this unit are not heat-damaged and are confirmed fully functional. Supplied with a short length of wiring for straightforward replacement of the right rear tail lamp socket (Peugeot 206 Combi).