This rear lamp bulb socket with a short wiring tail is a direct replacement part for Citroën C3 models manufactured until 2009. It addresses common lamp faults caused by corroded contacts, broken lampholders or damaged wiring, restoring reliable electrical connection for stop, tail and indicator functions. Ideal for professional workshops and experienced DIY mechanics who search by part number 6350Q3 / 6351Q3 / 6350X5 / 6351X5.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C3 (models up to 2009)
• Product Codes: 6350Q3, 6351Q3, 6350X5, 6351X5
• Additional Numbers: 6350Q3 | 6350X5 | 6351Q3 | 6351X5 | Citroën C3

Function and Application

The part houses the bulb sockets for the rear lamp cluster (left and right) and includes a short length of wiring to connect the lamp module to the vehicle harness. It provides electrical contacts for standard filament bulbs used in tail, brake and indicator circuits. This assembly replaces worn or damaged lampholders and short sections of harness that cause intermittent lighting or open circuits in the rear lights.

How To Replace

• Disconnect Battery Before Work To Prevent Short Circuits.
• Remove Rear Light Assembly: Open boot, remove retaining screws/clips and gently pull the lamp unit out to access the sockets.
• Extract Old Socket: Turn or unclip the old socket from the lamp housing and unplug the connector from the vehicle wiring harness.
• Install New Socket: Fit the new socket into the lamp housing, secure clips or twist into position and connect the wiring tail to the vehicle connector.
• Test Lighting Functions: Reconnect Battery and verify Tail, Brake and Indicator lights operate correctly before reassembling.
• Reassemble Lamp Unit: Reinstall the lamp assembly and tighten fasteners to manufacturer torque where specified.

Installation Recommendations

• Use Dielectric Grease On Contacts To Reduce Corrosion And Improve Long-Term Reliability.
• When Replacing, Inspect Bulbs And Lamp Seals; Replace Any Failed Bulbs And Renew Damaged Seals To Prevent Water Ingress.
• Ensure Connectors Are Clean And Free Of Corrosion; Repair Loom Insulation If Fraying Or Damage Is Present.
• If You Encounter Wiring Damage Beyond The Short Tail, Repair The Wiring Harness With Proper Automotive-Grade Materials.

Why The Part Commonly Fails

Rear lamp sockets fail most often due to moisture ingress and corrosion of the contacts, prolonged heat cycling from filament bulbs, mechanical vibration and brittle plastic after years of service. Water entering the lamp housing accelerates corrosion and can cause intermittent or complete loss of lighting. Damaged wiring insulation or connector pins are also frequent causes of failure.

This replacement socket is a straightforward, cost-effective repair to restore rear lamp functionality on affected Citroën C3 vehicles. Order by the referenced product codes to ensure you receive the correct lampholder assembly for your application.

Used rear lamp bulb holder designed for the Citroën C3 (first generation). This replacement socket accepts the standard rear lamp bulbs and is suitable for both left and right lamp assemblies. It is a practical spare for workshops and DIY mechanics who need to restore lighting functions such as tail, stop, indicator or reverse light (depending on the lamp variant). The item is commonly referenced by product codes and part numbers, so searching by code can speed up finding the correct replacement.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C3 (up to 2009)
• Product Codes: 6350Q3, 6351Q3, 6350X5, 6351X5
• Additional Numbers: Not specified

Function

The socket secures and provides electrical contact for the rear lamp bulbs. Depending on the lamp cluster configuration, it serves tail light, stop light (brake), turn signal (indicator) and/or reverse light functions. Proper seating and contact integrity are essential for reliable illumination and signal transmission.

How To Replace

1. Switch off ignition and all exterior lights before starting. 2. Open the boot and access the rear lamp from inside the luggage compartment—remove cover panels or trim as required. 3. Unscrew or unclip the lamp assembly and pull it out gently. 4. Unplug the wiring connector from the lamp and release the bulb holder/socket from the lamp housing. 5. Replace the old socket with the new one, ensuring bulbs are correctly seated and contacts are clean. 6. Reconnect the wiring connector, refit the lamp assembly and secure all fasteners and trim. 7. Test all lamp functions (tail, brake, indicator, reverse) before finishing reassembly.

Installation Recommendations

Wear gloves to avoid contaminating bulb glass. Inspect wiring plugs and contacts for corrosion or damaged insulation and clean contacts if necessary. Use dielectric grease on connectors to improve moisture resistance. Verify bulb types and orientation before refitting. If multiple lamp functions fail, check the vehicle fuse and ground connections as well.

Why This Part Commonly Fails

Common causes of failure include corrosion from moisture ingress, overheating of bulbs causing melted or brittle plastic, vibration fatigue, and UV degradation over time. Poor contact due to oxidized terminals or damaged wiring can lead to intermittent or complete loss of lamp function. Regular inspection and addressing moisture entry points in the lamp housing help extend service life.

Compatibility And Search Tips

Many customers search by the product codes shown above (6350Q3, 6351Q3, 6350X5, 6351X5) or by the vehicle model Citroën C3. Use these codes when looking for matching parts to ensure correct fitment.

Original right rear light Citroën C3 up to 2005 (pre-facelift), OEM 6351Q3. Used original part from disassembly – ideal replacement for a cracked or oxidized light. Thanks to the OEM design, it fits exactly, keeps the dimensions and color, without the need for modifications. Also often searched for as 6351.Q3 or 6351 Q3.

Technical information
– Location: right rear side (behind the passenger)
– Type of part: combined rear light (contour, brake, turn signal, reversing and possibly rear fog lights depending on equipment)
– Design: incandescent (not LED)
– Sockets/bulbs: not included – light is without bulb socket (use your existing one)
– Condition: used original part, fully functional; normal cosmetic wear corresponding to the age of the car (compare the condition with the photos)
– Manufacturer/concern: PSA Citroën/Peugeot
– Part Number (OEM/PSA): 6351Q3 (also listed as 6351.Q3, 6351 Q3)

Compatibility
– Citroën C3, years approx. 2002–2005 (before facelift), hatchback
– Right side (P)
– Note: does not fit C3 Pluriel

Why choose this part?
– Certainty of compatibility thanks to OEM number 6351Q3
– Significant savings compared to a new part, quick replacement without modifications
– Correct optics and visibility – safety and technical control in order

Assembly tips
– Before assembly, check the condition of the seals and clean the contact surfaces
– Transfer the original socket and bulbs, or replace the bulbs with new ones
– After installation, test all light functions (contour, brake, turn signal, reverse, fog light)

How to verify compliance
– Compare part number 6351Q3 with your original light or verify by VIN
– Check the shape, grips and connector of the socket according to the photos

Search keywords: rear light Citroën C3 right, right rear lamp C3 2002-2005, OEM 6351Q3, 6351.Q3, rear passenger light C3, genuine PSA part.