Original right rear light (rear lamp) for Citroën Xsara combi (break) with OE code 6351J8. The ideal replacement for a cracked, foggy or broken light – retain the original appearance and the correct geometry. This is the original removal part used, suitable for car mechanics and home repairers who need a quick and reliable solution.

The

part is designed for the right side of the car (passenger side at the steering wheel on the left). It corresponds to the original design – fits in serial handles and uses the original type of connector and sockets. Thanks to the same OE code 6351J8 you can achieve trouble -free mounting and proper function of light circuits.

Package content: rear lamp without socket and bulbs. The bolt base can be purchased in our country, which will facilitate replacement and shorten the repair time. Before mounting, we recommend checking the status of the seals and cleanliness of the bearing surfaces to avoid leaking into the lamp.

Typical reasons for replacement: mechanical damage after less collision, cracks after plastic aging, water root and subsequent corrosion of contacts, non -functional directional/brake/reverse. Inadequate rear light is a frequent reason for unsuccessful technical inspection, so timely replacement is also suitable for safety and legislation.

technical information
Manufacturer: Citroën (PSA)

Model: Citroën Xsara Estate (Break), Right side

product codes: 6351J8, 6351.J8
More Numbers: PSA NFP (No Further Production)

How to verify compatibility: The most reliable is to compare the OE number on the original episode or in the VIN catalog. If 6351J8 sits, the part is designed for your car. In case of doubt, always follow the part number, because there may be minor deviations according to the year of production or equipment.

Installation tips for replacement: Open the luggage compartment lid, remove the cap and loosen the fastening nuts/screws of the lamp, disconnect the electric connector and remove the old lamp. Transfer the bolt base (if you do not put it new), check the seals, sett down a new lamp into the body, evenly tighten the screws and test all the light functions (outline, brake, rudder, fog/reverse according to the equipment).

This right rear lamp socket is intended for Citroën Xsara Estate (Kombi) rear light assemblies and is frequently sought under part numbers 6351J8 or 6351.J8. The socket holds the rear bulbs (tail/brake/indicator/reverse depending on vehicle lamp cluster configuration) and connects to the vehicle wiring via the supplied short piece of cable. The straightforward design makes this part suitable for professional workshops and experienced DIY mechanics who need a direct replacement socket for the rear lamp cluster.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën Xsara Estate (Kombi)
• Product Codes: 6351J8
• Additional Numbers: 6351.J8

Installation Recommendations

Follow these practical steps for a safe and reliable replacement:

• Disconnect the battery before starting work to avoid short circuits and to protect vehicle electronics.
• Open the tailgate and remove the rear light cluster retaining screws or clips (access may require folding back trim or removing luggage trim panels).
• Carefully pull the lamp assembly out enough to access the bulb holders and wiring harness.
• Unplug the main connector and release the retaining tabs or twist-lock on the socket to remove the old holder.
• Fit the new socket into the lamp assembly until it locks in place, reconnect the harness and secure the lamp cluster back to the vehicle.
• Test all relevant light functions (tail, brake, indicator, reverse) after installation. Replace any faulty bulbs as bulb functionality is not guaranteed with this part.

Common Failure Reasons

• Corrosion of contacts caused by moisture ingress into the lamp housing, leading to poor electrical contact or intermittency.
• Heat damage from overloaded bulbs or poor contact, which can melt plastic sockets or deform terminals.
• Mechanical wear or broken retaining tabs from repeated bulb changes or rough handling during lamp removal.
• Wiring fatigue at the connector, especially where the harness is bent or chafes against the bodywork.

About Replacement Frequency And Function

There is no fixed service interval for lamp sockets; replacement is normally required after signs of corrosion, intermittent lighting, visible damage to the socket or connector, or when the socket no longer secures the bulb reliably. The socket’s function is to provide secure mechanical and electrical contact between the vehicle wiring and the rear bulbs; when it fails, one or more rear light functions can stop working or behave intermittently.

Notes For Professionals And Enthusiasts

Part number searches using 6351J8 or 6351.J8 commonly yield this socket for Xsara Estate models. When replacing sockets, inspect the lamp housing for signs of water entry and replace seals or gaskets if needed to avoid repeat failures. Use appropriate bulb types and ensure correct bulb seating to prevent overheating.