Direct-fit left rear lamp for the Citroën C2, supplied as an OEM-style replacement bearing codes 9649864580 and 6350S7. This rear combination lamp restores brake, tail and indicator lighting where applicable and is designed for easy installation by professional technicians and experienced DIY mechanics. The unit offers correct optics and mounting points to match original equipment, helping to maintain vehicle safety and road legality.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C2 (Typically 2003–2009)
• Product Codes: 9649864580, 6350S7
• Additional Numbers: NFP

Fitment And Function

This left rear lamp is a direct replacement for the rear combination lamp on Citroën C2 hatchback models. Depending on the vehicle variant, the assembly covers multiple light functions (tail, stop, and indicator). It uses the original mounting points and electrical connector format to ensure a secure fit and straightforward connection.

Installation Recommendations

1. Park The Vehicle On A Level Surface And Switch Off The Ignition.
2. Open The Tailgate And Remove Interior Trim Or Access Panel To Reach The Lamp Fixings.
3. Unscrew The Mounting Nuts Or Bolts Securing The Lamp Assembly And Carefully Pull The Lamp Outwards.
4. Unplug The Electrical Connector And Remove Bulbs If Required (Inspect Bulb Holders For Corrosion).
5. Fit The Replacement Lamp, Reconnect The Electrical Connector And Secure The Mounting Fasteners To The Correct Tightening Level.
6. Test All Light Functions (Tail, Brake, Indicator, Reverse Where Applicable) Before Reassembling Interior Trim.

Use Appropriate Hand Tools, Avoid Over-Tightening Plastic Fasteners, And Ensure Rubber Gaskets Or Seals Are Correctly Seated To Prevent Moisture Ingress.

Common Failure Reasons

• Water Ingress Causing Condensation Or Short Circuits Due To Worn Seals Or Damaged Lens.
• Impact Damage From Minor Collisions Or Bumping The Rear Of The Vehicle.
• Corroded Connector Pins Or Socket Contacts Leading To Intermittent Operation.
• Aged Or Broken Mounting Tabs Resulting In Poor Fitment And Vibration Damage.
• Bulb Failure Inside The Assembly; Check Bulb Type And Condition When Replacing The Unit.

Why Choose This Part

This left rear lamp is supplied to match original equipment specifications, making it a reliable choice for body repairs, insurance replacements and routine maintenance. Commonly searched by OE numbers 9649864580 and 6350S7, the assembly helps restore correct light output and vehicle appearance with a straightforward fitment process.

High-quality replacement rear bulb socket designed specifically for the Citroën C2. This socket secures the bulb in the tail lamp housing and provides the electrical contacts required for brake, tail, and indicator lights. Supplied with a short piece of wiring to simplify installation and ensure reliable contact. Ideal for professional auto workshops and DIY mechanics looking for a direct-fit repair part under references 6351S7 and 6350S7.

Function And Application

The bulb holder (socket) is responsible for mechanically holding the bulb and providing stable electrical connection between the vehicle wiring and the lamp. Correct operation is essential for brake light, tail light, and turn signal function. This part is used in the rear lamp assemblies on Citroën C2 models and fits both left and right tail lights.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C2
• Product Codes: 6351S7, 6350S7
• Other Numbers: Not Available

Installation Recommendation

Replacement is straightforward for experienced mechanics and competent DIYers. Typical procedure:

• Remove the tail lamp assembly from the vehicle (access from the luggage compartment; keep trim and fasteners safe).
• Twist or unclip the old bulb socket from the lamp reflector and disconnect the wiring connector.
• Fit the new socket into the lamp housing, connect the wiring harness and secure the socket in place.
• Refit the lamp assembly, tighten fasteners to the correct torque, and test all light functions (tail, brake, indicator).

Use appropriate hand tools and check seals/gaskets to prevent water ingress. If wiring is brittle or corroded, replace or repair the harness section rather than stretching the new socket wiring. After installation, verify lamp alignment and function before finishing work.

Most Common Failure Causes

• Corrosion Of Contacts: Moisture ingress or salt buildup causes poor electrical contact and intermittent lighting.
• Heat Damage: Overheating from an incorrect bulb type or poor contact can melt plastic sockets and deform contacts.
• Mechanical Wear And Vibration: Repeated removal/installation or vibration can crack the plastic or loosen the connection.
• Water Ingress And Seal Failure: Damaged lamp seals allow water to reach the socket and wiring, accelerating corrosion.

Why Choose This Part

Direct-fit design for Citroën C2 makes replacement fast and reliable. Supplied with a short wiring tail to simplify reconnection and reduce the need for splicing. Suitable for both professional garages and competent DIY repairs where a durable, OEM-compatible socket is required.

Notes

Check bulb type and lamp condition when replacing the socket. Using the correct bulb wattage and ensuring the lamp housing is dry and sealed will extend service life. Follow safe workshop practices and use proper personal protective equipment during installation.