This left rear tail lamp is a direct-fit replacement for the PEUGEOT 307 SW (estate) up to 2005 and is ideal for professional workshops and DIY mechanics who need a reliable, correctly fitting lamp. Supplied without bulb holders, it allows flexible installation when you already have functional sockets or prefer to install new holders separately. The part is commonly searched under the product code 6350Q6, so use that reference when locating the correct item for your vehicle.

Benefits And Fitment

Designed to match OE mounting points and contours, this lamp restores correct exterior lighting function and appearance. It provides clear signalling for brake, tail and indicator functions (bulbs and holders not included). Ideal for collision repairs, corrosion-damaged assemblies or when lens cracking lets moisture in. Robust housing and lens geometry ensure correct light dispersion and a factory-like finish after replacement.

Installation

1. Open the tailgate and remove any interior trim panels covering the lamp mounting area.
2. Unscrew the retaining bolts/nuts securing the lamp assembly (typically accessible from inside the boot).
3. Carefully pull the lamp unit out enough to reach the electrical connector and unplug it.
4. If present, remove old bulb holders/sockets from the lamp and transfer or replace bulbs as required (this unit is supplied without holders).
5. Position the new lamp into the body flange, align the mounting points and fasten the retaining bolts/nuts securely.
6. Reconnect the electrical connector and test all lamp functions (tail, brake, indicator, reverse if applicable).
7. Refit the interior trim and close the tailgate. Check gaps and alignment for a uniform finish.

Installation Recommendations

Always disconnect the vehicle battery before starting to avoid short circuits. Handle the lens and housing carefully to avoid scratches. Clean and inspect connectors and wiring for corrosion; apply dielectric grease to contacts to improve conductivity and future corrosion resistance. Replace damaged gaskets or seals to prevent water ingress. After installation, verify correct operation of all lamp functions and adjust alignment if necessary.

Why This Part Most Commonly Fails

• Impact Damage: Rear-end collisions and minor knocks easily crack lenses or break mounting tabs.
• Water Ingress: Damaged seals or cracked lenses let moisture into the assembly, causing condensation and electrical faults.
• Connector And Socket Corrosion: Exposure to road salt and moisture corrodes contacts and bulb holders, causing intermittent or failed lighting circuits.
• Plastic Fatigue: Aging and UV exposure can make mounting points brittle, leading to broken tabs and poor fitment.

Technical Information

• Manufacturer: PEUGEOT / Stellantis
• Model: Peugeot 307 SW (Estate), Left Rear, Up To 2005
• Product Codes: 6350Q6
• Other Numbers: NFP (as listed)

Practical Notes

This lamp is a practical choice for technicians and independent mechanics restoring rear lighting on the Peugeot 307 SW. Because the unit is supplied without bulb holders, verify the correct bulb types and holders required for your vehicle before fitting. After replacement, always test brake, tail and indicator lights from outside the vehicle and with an assistant if possible to ensure full functionality and safety compliance.

This replacement lamp holder is intended for mechanics and DIY enthusiasts who need a reliable connection point for rear light bulbs on Peugeot 307 Estate/SW models produced up to 2005. The unit includes the plastic socket(s) with bulbs (functionality of the bulbs is not guaranteed) and a short length of wiring to reconnect the socket to the vehicle harness. Ideal for repairing broken contacts, melted holders or damaged wiring in the tail lamp cluster.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307 Estate / SW (pre-2005 models)
• Product Codes: 6350Q6, 6351Q6
• Additional Numbers: 89026938, 89026198

Key Features And Function

The socket secures the brake, tail and indicator bulbs inside the rear lamp cluster and provides the electrical contacts to the vehicle wiring. It restores proper seating of bulbs and stable electrical contact, preventing flicker or intermittent operation caused by loose or corroded contacts. Supplied with a piece of wiring to facilitate replacement of damaged wiring sections.

Replacement Procedure

Typical steps for replacement (general guidance):

• Access the rear lamp from the luggage compartment: open the boot and remove or fold back the interior trim to reach the lamp cluster fasteners.
• Disconnect the multi-pin connector from the lamp cluster and remove any retaining screws or clips holding the lamp assembly.
• Remove the lamp cluster or reach behind to twist out the bulb holder(s) from the lamp body.
• Unplug the old socket from the wiring harness. If the original wiring is damaged, use the supplied piece of wiring to make a clean splice with insulated crimps or solder and heat-shrink tubing.
• Install the new socket into the lamp body, secure the lamp cluster, reconnect the multi-pin connector and test all rear light functions (tail, brake, indicator, reverse if applicable).

Installation Recommendations

• Work in a dry, well-lit area and keep small parts organized. Protect painted surfaces when removing panels.
• Inspect and clean the lamp connector pins; remove corrosion and apply dielectric grease to contacts to improve conductivity and corrosion resistance.
• Replace damaged rubber grommets or seals to prevent water ingress into the lamp unit.
• Use proper crimping tools or soldering with heat-shrink for wiring repairs. Avoid twisting wires without insulation.
• After installation, verify all light functions and check for secure mechanical fitment. Replace any blown fuses or faulty bulbs as needed.

Why This Part Fails

Common causes of socket failure include heat damage from high-load bulbs, plastic aging and brittleness, corrosion of electrical contacts due to moisture ingress, mechanical stress from repeated bulb changes, and accidental damage during trunk loading. Wiring fatigue or chafing behind the lamp cluster can also lead to intermittent or complete loss of function.

Additional Notes

This part is frequently searched by its product codes (6350Q6, 6351Q6, 89026938, 89026198). Ensure correct bulb types and secure seals when replacing the socket to extend service life.