Direct-fit Left Rear Tail Light for Peugeot 3008 I, identified by part numbers 9683460880 and 6350HC. Designed for professional workshops and DIY mechanics who need a reliable replacement for a broken or worn rear lamp housing. This unit restores rear lighting functionality and vehicle appearance while matching OE mounting points for straightforward installation.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 3008 I (First Generation)
• Product Codes: 9683460880, 6350HC
• Other Numbers: 6350.HC
• Side: Driver Side (Left)
• Notes: Supplied without bulb sockets; bulb holders and bulbs sold separately.

Fitment

Compatible with Peugeot 3008 First Generation models (3008 I). Verify model year and body style against listed part numbers 9683460880 / 6350HC when selecting the part.

Installation Recommendations

Basic replacement steps for a mechanic or competent DIYer:
1. Open the tailgate and remove the interior trim panel to access the lamp fasteners.
2. Unscrew the mounting bolts (usually 2–3) and carefully unclip any plastic retainers.
3. Disconnect the electrical connector from the lamp assembly.
4. Remove the old lamp, transfer any reusable seals or gaskets, and fit the new lamp into position.
5. Reconnect the wiring harness, secure the lamp with the original fasteners, and refit the trim panel.
6. Install bulb holders and bulbs if required, then test all functions (brake, tail, turn signal, reverse if applicable).
Safety tip: Before handling electrical connectors, isolate the vehicle electrical system or disconnect the negative battery terminal to reduce the risk of short circuits. Use dielectric grease on connectors and check seals to prevent moisture ingress.

Why The Part Commonly Fails

• Water Ingress: Damaged seals or cracked lenses allow moisture to enter, causing corrosion and electrical faults.
• Impact Damage: Bump or collision at the rear often cracks the housing or breaks mounting tabs.
• Plastic Fatigue: Mounting clips and tabs can become brittle over time and snap during removal or from vibration.
• Connector Corrosion: Oxidation on terminals or damaged wiring leads to intermittent or permanent failure of light functions.
• Bulb Holder Wear: Although this unit is supplied without bulb sockets, worn or corroded bulb holders in the vehicle can give the appearance of lamp failure.

Additional Tips

When replacing the rear lamp, inspect the surrounding seals and wiring harness for damage. Replace any brittle clips or degraded gaskets to maintain a watertight fit. Keep the part numbers 9683460880 and 6350HC handy when ordering bulbs, sockets, or future replacements to ensure correct compatibility.

Keywords: Left Rear Tail Light, Peugeot 3008 Tail Lamp, 9683460880, 6350HC, Rear Lamp Replacement, Driver Side Taillight.

Product Description

This Used Bulb Socket Is Intended For The Left Rear Tail Lamp Of The PEUGEOT 3008 T84 (3008 I). It Replaces Worn Or Damaged Bulb Holders And Includes A Short Length Of Wiring For A Faster, Safer Swap. The Part Is Often Searched By Its Reference Numbers, So Listing The OEM Codes Below Helps You Find An Exact Fit Quickly.

Key Benefits

• Direct Fit For Left Rear Lamp Assemblies On PEUGEOT 3008 T84.
• Includes Wiring Pigtail To Avoid Cutting Factory Harness—Speeds Up Repair.
• Cost-Effective Replacement For Faulty Or Corroded Sockets.
• Commonly Searched By Product Codes (Use These In Parts Lookups Or Catalogs).
• Suitable For Professional Workshops And DIY Mechanics Who Perform Tail Light Repairs.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: PEUGEOT 3008 T84 (3008 I)
• Product Codes: 9683460880, 6350HC
• Other Numbers: 6350.HC, 6350HC, 9683460880

Installation Guidance

Designed For Mechanics And Competent DIYers. Typical Replacement Steps:

• Switch Off Ignition And, For Extra Safety When Working With Wiring, Disconnect The Negative Battery Terminal.
• Access The Left Rear Tail Light Assembly From The Boot/Trunk: Remove Trim Fasteners And Unscrew The Lamp Unit.
• Disconnect The Old Bulb Socket From The Housing And Unplug The Connector From The Vehicle Harness.
• Compare The New Socket And Wiring To The Old One (Pin Layout And Bulb Type). Fit The New Socket Into The Lamp Housing And Secure The Connector.
• If Required, Use Proper Crimps Or Soldering For Any Wire Joins, Protect Joints With Heat-Shrink Tubing, And Ensure A Secure Mechanical Fix To Avoid Strain.
• Test All Light Functions (Brake, Tail, Indicator, Reverse As Applicable) Before Reassembling The Lamp Unit.
• Reinstall The Lamp Assembly And Trim Panels, Then Reconnect The Battery.

Why This Part Fails Most Often

• Corrosion Of Contacts Due To Moisture Ingress Or Damaged Seals.
• Plastic Deformation Or Melting From Overheating (Incorrect Bulb Wattage Or Poor Contact).
• Broken Pins Or Cracked Housing From Vibration, Impact, Or Repeated Bulb Changes.
• Wiring Fatigue Where The Pigtail Meets The Harness—Especially On Older Vehicles.

Practical Tips

• Replace The Socket When You Replace A Bulb If Contacts Look Corroded Or Loose.
• Use Dielectric Grease On Contacts To Reduce Corrosion And Improve Electrical Contact.
• Verify Bulb Type And Wattage Against Manufacturer Specification To Avoid Overheating.
• Secure Wiring To Prevent Rubbing Against Sharp Edges; Use Cable Ties Or Protective Looms.

Compatibility Notes

Fits PEUGEOT 3008 T84 (First Generation) Rear Left Lamp Applications. Buyers Often Search Using The Product Codes 9683460880 Or 6350HC—Include These In Your Parts Search To Confirm Match With Your Lamp Unit.