Overview

This Valeo TS22E26 CL6 starter is a reliable direct-fit unit for a range of PSA HDi engines. Designed for Citroën and Peugeot models with 1.4, 1.5 and 1.6 HDi engines, it replaces the original starter and carries the common OEM references used in Stellantis applications. The unit is ideal for mechanics and experienced DIYers looking for a quality replacement that matches factory specifications in voltage and pinion tooth count.

Features and Benefits

• Direct Replacement: Matches OEM fitment and mounting points for straightforward swap.
• Proven Design: Valeo construction with compatible electrical and mechanical interfaces for PSA HDi engines.
• Correct Electrical Rating: 12 V operation suitable for standard 12 V vehicle systems.
• Pinion Specification: 11 teeth pinion suitable for the corresponding flywheel/ring gear.
• Cost-Effective Repair: Restores reliable starting performance when original starter fails.

Fitment

Compatible With: Citroën Berlingo, Citroën C4, Citroën Xsara Picasso, Peugeot 207, Peugeot 307, Peugeot 308, Peugeot Partner (1.4 HDi, 1.5 HDi and 1.6 HDi engine variants). Always verify engine code and physical fitment before installation.

Technical Information

• Manufacturer: Valeo
• Model: TS22E26 CL6 (1.4 HDi / 1.5 HDi / 1.6 HDi)
• Product Codes: 9646694080, 9662854180, TS22E26
• Additional Numbers: 5802AE, 5802AF, 5802CE
• Voltage: 12 V
• Number Of Teeth: 11
• Source Condition: Sourced from a vehicle with mileage up to 100,000 km

Installation Recommendation

Disconnect the negative battery terminal before starting and follow safe workshop procedures. Typical replacement steps: raise and support the vehicle securely, remove any obstructing components (heat shields or intake parts as required), disconnect electrical connectors and the starter solenoid wiring, unbolt the starter from the transmission bellhousing, inspect the flywheel ring gear and starter mounting faces for damage, fit the replacement unit, reconnect wiring and lower the vehicle. Torque fasteners to the manufacturer’s specifications and reconnect the battery last. If you are not confident with the procedure, have the installation performed by a qualified technician.

Most Common Failure Causes

• Brush and Commutator Wear: Normal wear over time reduces contact and starting performance.
• Solenoid Failure: Coil or contacts in the solenoid can fail, preventing engagement or current flow.
• Pinion or Ring Gear Damage: Worn teeth or damaged ring gear prevent positive engagement.
• Contamination: Oil or debris ingress shortens life and causes mechanical binding.
• Electrical Issues: Weak battery, poor ground or corroded connections cause excessive heat and premature starter failure.
• Frequent Short-Run Starts: Repeated cranking without adequate alternator recovery can overheat and wear the starter.

Practical Tips

• Check Battery And Charging System Before Replacement: Many perceived starter failures are caused by low battery voltage or charging faults.
• Inspect Flywheel Teeth And Mounting Faces: Repair or replace damaged components to avoid repeat failures.
• Ensure Clean Electrical Connections: Clean and tighten battery and starter terminals for reliable current flow.
• Listen For Symptoms: Grinding, intermittent operation, or slow cranking are common early warnings.

The Valeo TS22E26 CL6 starter is a direct-fit solution for a range of Stellantis diesel engines (1.4 HDi, 1.5 HDi, 1.6 HDi) used in many Citroën and Peugeot models. This used unit is supplied with a guarantee of functionality and is an economical choice for workshops and DIY mechanics looking to restore reliable starting performance. Key search terms: Valeo Starter TS22E26, CL6 Starter, 12V Starter, Citroën Peugeot HDi Starter, 5802AE, 9662854180, 9646694080.

Technical Information

• Manufacturer: Valeo
• Model: TS22E26 CL6
• Product Codes: 5802AE, 5802AF, 5802CE
• Additional Numbers: 9646694080, 9662854180
• Voltage: 12 V
• Number Of Teeth: 11
• Condition: Used Part With Functional Guarantee

Compatibility

Commonly fitted to the following models and engine families: Citroën Berlingo, Citroën C4, Citroën Xsara Picasso, Peugeot 207, Peugeot 307, Peugeot Partner. Designed for 1.4 HDi, 1.5 HDi and 1.6 HDi diesel engines. Ensure the part numbers listed above match the unit being replaced.

Function And Common Failures

The starter motor engages the engine flywheel to crank the engine at ignition. Typical failure modes include worn pinion gear or flywheel teeth, failed solenoid, electrical wear in brushes and commutator, seized bearings, and poor electrical connections (corroded battery terminals or earth straps). Heat, contamination and high cranking loads accelerate wear.

Installation Recommendations

• Disconnect the negative battery terminal before starting work to avoid short circuits.
• Gain safe access to the starter (under the vehicle or through the engine bay depending on model) and support the vehicle securely on stands.
• Label and photograph electrical connections before removal to ensure correct reassembly.
• Remove the power cable and the solenoid connector, then unfasten the mounting bolts and withdraw the starter.
• Inspect the flywheel ring gear for damaged teeth and check the condition of the wiring harness and earth straps.
• Replace mounting bolts if corroded or stretched and tighten to the manufacturer’s torque specification (refer to the vehicle repair manual).
• After fitting, verify starter engagement and listen for abnormal noises; check battery voltage and starter current draw if issues persist.

Why The Part Most Often Fails

Starters on HDi diesel vehicles commonly fail due to cumulative wear from frequent cold starts, contamination (oil or debris), heat exposure near the exhaust or turbocharger, degraded brushes and bearings, or from electrical problems such as a weak battery or poor earth connections. Mechanical damage to the ring gear or pinion engagement is also a frequent cause.

Replacement Procedure And Time

Basic replacement steps: safely lift and support the vehicle, disconnect battery, remove electrical connectors and mounting bolts, extract old starter, fit replacement and reconnect cables. Typical fitment time ranges from 0.5 to 2 hours depending on vehicle layout and any obstacles (intake piping, heat shields, etc.). Always follow the vehicle manufacturer’s procedure and torque data.

Ideal for both professional mechanics and car enthusiasts who prefer self-repair, this starter offers easy installation without the need for specialized tools or modifications. Starters commonly wear out due to repetitive use and mechanical stress, but this Valeo unit provides long-lasting performance and dependable starting power to keep your vehicle running smoothly.

Technical Information

• Manufacturer: Valeo
• Model: TS22E26 CL6
• Product Codes: 9646694080, 9662854180
• Additional Numbers: 5802AE, 5802CE, 5802AF

This starter is compatible with various PSA Citroën and Peugeot models featuring 1.4 HDI and 1.6 HDI engines. Its standard fitting ensures straightforward replacement, making it an ideal component for restoring your vehicle’s original starting performance and ensuring reliable everyday operation.

Before installation, it is recommended to verify the part numbers and compatibility with your specific vehicle model and engine type to guarantee proper fitment and function.