This electric parking brake (EPB) mechanism is a direct-fit used component for Peugeot 3008 I models. Ideal for professional workshops and experienced DIY mechanics, the unit replaces the hydraulic/electric rear parking brake actuator and restores automatic handbrake operation. Commonly searched by product numbers, the listing includes multiple OEM references to help you find the correct fit: include any of the listed codes when searching (0204706357, 9673094880, 470209, 470212).

Function And Benefits

The EPB mechanism converts driver inputs from the parking brake switch into mechanical clamping force at the rear brake calipers via a small electric motor and gearbox. It provides reliable parking brake engagement, hill-hold capability on some vehicles, and enables automatic release during driving. Replacing a faulty mechanism returns smooth actuation and prevents warning lights or permanent handbrake engagement that can limit vehicle use.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I (First Generation)
• Product Codes: 0204706357, 204706357, 9673094880
• Additional Numbers: 470209, 470212

Installation Recommendations

• Disconnect the battery before starting work and follow the vehicle manufacturer’s safety procedures.
• Work With The Rear Wheel Raised And Securely Supported. Remove Wheel And Access Rear Caliper/Actuator Assembly.
• Remove Interior Trim If Needed To Access Parking Brake Switch/Connector. Unplug Electrical Connector From The Actuator.
• Unbolt The Actuator From The Caliper Or Carrier. Retain Fasteners If They Are Serviceable; Replace If Corroded Or Damaged.
• Install New Unit, Reconnect Electrical Connector And Reassemble. Tighten Fasteners To Manufacturer’s Torque Specifications.
• After Mechanical Fitment, An Initialization/Calibration Procedure With A Diagnostic Tool May Be Required To Set EPB Limits And Clear Faults.
• If You Are Not Equipped With Proper Diagnostic Tools, Commission The Final Calibration To A Workshop With PSA-Compatible Equipment.

Why This Part Commonly Fails

• Wear Of The Small Electric Motor Or Gearbox Due To High Mileage And Frequent Use.
• Corrosion And Seizure Caused By Water Ingress, Road Salt Or Poor Sealing Around The Caliper/Actuator.
• Electrical Connector Corrosion Or Broken Wiring Leading To Intermittent Operation Or Fault Codes.
• Mechanical Seizure Of Caliper Slider Pins Or Brake Pads Causing Excessive Load On The Actuator.

Notes For Professionals And Enthusiasts

When replacing the EPB mechanism, inspect rear brake hardware (calipers, pads, sliders) and the handbrake switch for related issues to avoid repeated failures. Replacement often resolves persistent handbrake warning lights and prevents the vehicle from being immobilized by a stuck parking brake. Keep the listed product codes handy when searching stock or ordering replacement parts to ensure correct matching.

High-quality replacement electronic parking brake (EPB) mechanism for Peugeot 3008 I. Ideal for professional workshops and DIY enthusiasts looking for a direct-fit actuator. Commonly searched by part numbers, this unit restores reliable parking brake operation and eliminates warning lights or failure messages related to the electric handbrake system.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Peugeot 3008 I (First Generation)
• Product Codes: 0204280099, 9684898480
• Other Numbers: 470209, 470212, 9688061780, 0204280126, 204280099, 204280126

Function And Fitment

The electronic parking brake mechanism converts electronic commands from the vehicle control module into mechanical clamping force on the rear brakes, securing the vehicle when parked. This unit is intended for fitment on first generation Peugeot 3008 rear brake assemblies and is compatible with vehicles using the EPB system controlled by the car’s onboard electronics. Customers frequently locate this part by its reference numbers listed above.

Replacement Procedure

Basic replacement steps (for experienced technicians):

• Disconnect The Battery Before Starting Work To Prevent Short Circuits And Protect Electronics.
• Raise The Vehicle Securely And Remove The Rear Wheel To Access The Brake Assembly.
• Remove Any Brake Shielding Or Caliper Covers To Reach The EPB Actuator.
• Unplug The Electrical Connector From The Actuator And Unbolt The Unit From The Caliper/Subframe.
• Transfer Any Required Brackets Or Sensors From The Old Unit To The New Unit If Needed, Then Fit The Replacement Actuator.
• Reconnect The Electrical Connector, Refit Wheels, Lower The Vehicle And Reconnect The Battery.
• Perform EPB Initialization/Calibration Using A Suitable Diagnostic Tool To Ensure Proper Operation (See Notes Below).

Installation Recommendations

• Always Disconnect The Battery Before Removal And Follow Manufacturer Procedures To Avoid Damage To The Unit.
• Use A Service Manual Or Manufacturer Repair Instructions For Torque Settings And Specific Removal Steps.
• After Installation, Calibrate The EPB System With A Diagnostic Tool. If The Vehicle Shows A Parking Brake Fault, Recheck Electrical Connections And Perform An Adaptation Routine.
• Replace Seals Or Fasteners That Appear Corroded To Prevent Water Ingress Causing Early Failure.

Why This Part Fails Most Commonly

• Water Ingress And Corrosion In The Actuator Or Linkages Leading To Seized Components.
• Mechanical Wear Of Gears Or Cable Mechanisms Causing Loss Of Clamping Force.
• Electrical Motor Or Internal Encoder Failure Resulting In Inability To Retract Or Engage The Brake.
• Damage From Impact Or Improper Previous Repairs Affecting Alignment Or Mounting.

Practical Tips For Mechanics

Search By Part Number For Faster Identification. Check The Condition Of The Rear Brake Pads, Calipers And Cables When Replacing The EPB Actuator, Because Related Wear Can Mask As Actuator Faults. Keep The Connector Contacts Clean And Use Contact Cleaner If Corrosion Is Present.

Additional Notes

Unit Shown As Tested Functional In The Original Description. After Fitting, Observe The Parking Brake Operation Through At Least One Complete Engage/Release Cycle And Clear Any Stored Fault Codes With A Diagnostic Tool.