This complete lock set is a practical replacement for workshops and DIY enthusiasts working on Peugeot 206 models. Supplied as a ready package including door locks, fuel filler cap and ignition lock cylinder with two keys, it reduces downtime and the need to source individual components. The set is ideal for common repairs such as worn tumblers, seized cylinders or damage following forced entry. Key part numbers are included to help you find this item quickly: 1692330580, 4162NR, 4162Z1, 4162EZ, 4162EW.

Features

• Complete Set: Driver’S Door Lock, Passenger Door Lock, Fuel Filler Cap And Ignition Lock Cylinder.
• Includes Two Keys: Ready To Use With The Supplied Keys.
• Condition Note: One Door Lock Shows Minor Cosmetic Damage But Remains Fully Functional.
• Direct Replacement For Standard Mechanical Locking Systems On Peugeot 206.

Compatibility

Compatible With: Peugeot 206 (Including 206+ Variants Where The Same Lock Assembly Is Used). Always Check Part Numbers Against Your Vehicle Requirements When Searching.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 206
• Product Codes: 1692330580, 4162NR, 4162Z1, 4162EZ, 4162EW
• Additional Numbers: 4162.EW, 4162.EZ, 4162.NR, 4162.Z1

Installation Recommendations

• Preparation: Have The Correct Keys, Basic Hand Tools (Screwdrivers, Torx/Hex As Required), Trim Tools And Penetrating Lubricant Ready.
• Safety: Disconnect The Battery Before Starting Work To Avoid Short Circuits And Follow Manufacturer Procedures When Removing Interior Trim And Steering Column Covers.
• Door Lock Replacement: Remove Door Trim Panel, Detach Linkage Rods And Electrical Connectors, Unscrew Lock Assembly From Door Shell, Fit New Lock And Reconnect Linkages. Check Smooth Operation Of Central Locking After Reassembly.
• Ignition Lock Cylinder Replacement: Remove Steering Column Covers, Release The Retaining Clip Or Screw Holding The Cylinder, Slide Out The Old Cylinder And Install The New One. Test Key Operation Before Reinstalling Covers.
• Final Checks: Ensure All Rods And Clips Are Correctly Seated, Lubricate Lock Mechanisms With Suitable Graphite Or Light Lock Grease, And Verify That Doors, Fuel Cap And Ignition Work Smoothly With The Supplied Keys.

Why This Part Commonly Fails

Lock Components Wear Over Time Due To Mechanical Use, Dirt Ingress, Corrosion From Moisture And Road Salt, Or Key Wear. Common Failures Include Stiff Or Intermittent Key Operation, Broken Tumblers, Rods Or Clips, And Seizure Of The Cylinder. Damage Can Also Result From Forced Entry Attempts Or Improperly Aligned Linkages Following Previous Repairs.

Practical Advice For Workshops And DIYers

• When Replacing Multiple Locks, Consider Rekeying Or Ensuring All Locks Use The Same Keying For Convenience.
• Minor Cosmetic Damage Does Not Necessarily Affect Function—Inspect Mechanically Before Deciding On Replacement.
• For Best Results, Test The Complete Set On The Vehicle Before Final Reassembly.

Order This Peugeot 206 Lock Set By Part Number To Speed Up Your Search And Get Your Vehicle Back On The Road Quickly.

High-quality replacement lock set designed for Peugeot 206 vehicles, ideal for professional mechanics and experienced DIY enthusiasts. This kit contains the main mechanical locking components used daily: driver and passenger door locks, the fuel cap lock and the ignition barrel, supplied with one key. Note that one door lock fitted with a white plastic latch is currently non-functional and may require repair or replacement of the latch mechanism. Search keywords: Peugeot 206 lock set, 4162EW, 4162Z1, door lock kit, ignition barrel replacement.

Function And Application

The locks in this set secure vehicle access, operate the central locking system where fitted and provide ignition switching via the barrel and key. The kit is intended primarily for Peugeot 206 models (hatchback variants such as 3‑door and 5‑door). Compatibility depends on equipment and part codes listed below — verify the part numbers against the original component before installation.

How The Part Is Replaced

Typical replacement steps for the door locks and ignition barrel:

• Door Locks: Remove the interior door trim and water shield to access the lock assembly. Disconnect rods and electrical connectors (if central locking actuator present), remove mounting screws and slide the old lock out. Fit the new lock, reconnect linkages and check mechanical movement before refitting trim.
• Ignition Barrel: Remove steering column covers, extract any retaining clip or fixing screw and withdraw the old barrel. Install the new barrel aligned with the steering lock and test key operation before reassembling trims.
• Fuel Cap: Remove the filler-flap trim or hinge screws as required and swap the cap assembly. Ensure proper sealing and operation of the flap catch.

Installation Recommendations

• Work With The Door Open And The Vehicle Secure; Use Suitable Trim Tools To Avoid Damage.
• Inspect Linkages And Actuator For Wear Or Corrosion And Replace If Necessary.
• Lubricate Lock Mechanisms With A Dry Graphite Or Silicone-Based Product Suitable For Automotive Locks; Avoid Heavy Greases That Attract Dirt.
• After Fitting, Verify Smooth Mechanical Operation And Central Locking Function (If Applicable) On All Doors, Ignition And Fuel Flap.
• Keep The Supplied Key Safe And Check That It Operates All Fitted Locks Before Reassembling Trim.

Most Common Failure Reasons

• Plastic Latch Breakage: Small white plastic components inside the lock can become brittle and break, leading to non-functional latches — this is consistent with the current non-functional door lock in this set.
• Corrosion And Water Ingress: Moisture in the door or filler area causes corrosion of metal parts and seizing of mechanisms.
• Wear Of Tumblers And Keys: Frequent use and worn keys can prevent correct engagement of the ignition barrel.
• Actuator Failure: Central-locking actuators fail electrically or mechanically, giving the impression of a faulty lock.
• Mechanical Impact Or Vandalism: Forced entry attempts can deform or break locking components.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 206
• Product Codes: 4162EW, 4162Z1
• Other Numbers: 4162NR, 1692330580

Notes

This kit is supplied with one key. The set includes a door lock that currently has a non-functional white latch — consider inspecting or replacing the plastic latch during installation. Always match the codes above to the original part number on the vehicle to confirm compatibility.