This ABS hydraulic control block is designed for Peugeot 206 applications and compatible Stellantis models carrying the same part numbers. The unit controls hydraulic modulation of the braking system during ABS events and integrates the pump and valve block (hydraulic modulator) with the electronic control to ensure stable deceleration and wheel-slip prevention. Ideal for professional workshops and experienced DIY mechanics who service braking systems on Citroën/Peugeot vehicles.

Function And Typical Symptoms

The ABS hydraulic control block regulates brake pressure at each wheel via solenoid valves and an electric pump under commands from the ABS electronic control. Common symptoms indicating a faulty module include steady or flashing ABS warning light on the dashboard, reduced braking stability during emergency braking, audible pump motor operation after ignition, or brake pressure loss/leakage at the unit. Note that ABS faults can also be triggered by wheel speed sensors or wiring issues; a targeted diagnosis is recommended.

Compatibility And Fitment

Main Fitment: Peugeot 206. Also referenced by Stellantis/Citroën/Peugeot original numbers listed below. Check vehicle part numbers to confirm match before installation.

Technical Information

• Manufacturer: ATE / Stellantis (Citroën/Peugeot)
• Model: Peugeot 206
• Product Codes: 9659136980, 10.0970-1128.3, 10.0207-0068.4
• Other Numbers: 9652342980, 10.0970-1114.3, 10.0207-0036.4, 4541V5, 4541V6, 4541RW, 1682608780

Installation Recommendations

• Work Should Be Performed By A Qualified Technician Or An Experienced Mechanic Familiar With Brake Systems.
• Always Follow Manufacturer Service Procedures. Before Starting, Isolate The Electrical System Where Appropriate And Take Safety Precautions.
• Locate The ABS Hydraulic Unit (Typically Near The Brake Master Cylinder In The Engine Bay), Disconnect The Electrical Connector And Carefully Remove The Brake Lines From The Unit Using Proper Tools To Prevent Damage.
• Cap Brake Lines To Prevent Contamination And Minimize Fluid Loss. Unbolt The Unit And Replace With The Correct Part. Replace Any Sealing Washers Or Crush Rings As Required.
• After Mechanical Fitment, Refill And Correctly Bleed The Brake System To Remove All Air. Use A Proper Brake Bleeding Procedure (Ideally A Pressure Or Vacuum Bleeder) And The Correct Brake Fluid Specified By The Manufacturer.
• Use A Diagnostic Tool To Clear ABS Fault Codes And Run Any Required Self-Tests Or Adaptations. If Codes Persist, Inspect Wiring And Wheel Speed Sensors.
• Check For Hydraulic Leaks And Secure All Fasteners To Manufacturer Torque Specifications.

Why This Part Most Commonly Fails

• Corrosion And Moisture Ingress Causing Electrical Or Hydraulic Failure.
• Wear Or Contamination In The Valve Block Leading To Leaks Or Improper Modulation.
• Pump Motor Wear Or Electrical Faults In The Module Electronics.
• Damaged Or Corroded Connectors And Wiring Harnesses Causing Intermittent Signals.
• Contaminated Or Old Brake Fluid Accelerating Internal Component Degradation.

Additional Notes

The Unit Is Supplied With A Section Of Wiring As Indicated. After Replacement, Perform Full System Checks And Road Test To Confirm Correct ABS Operation And Brake Performance.

Are you looking for reliable and high-quality automotive parts for your Peugeot 206 or 206+? The Peugeot ABS control module ensures full restoration of your vehicle’s braking system functionality, which is critical for your safety on the road. Installation is quick and straightforward, ideal for both professional mechanics and DIY enthusiasts.

Our ECU ABS – the Electronic Control Unit for the anti-lock braking system – is specifically designed for Peugeot 206 and 206+ models. Being equipped with part of the wiring harness simplifies the assembly and commissioning process. This unit meets stringent standards and functional requirements for optimal braking performance.

Technical Information:

• Manufacturer: ATE
• Model: Peugeot 206, 206+
• Product Codes: 9675185380, 10.0207-0220.4, 10.0970-1170.3
• Additional Numbers: 4541V5, 4541V6, 4541RW, 1682608780

This ABS control module is indispensable for the proper functioning of your vehicle’s brake system. It prevents wheel lock-up during sudden braking, allowing better vehicle control and reducing stopping distances, which is vital for your safety in emergency situations.

When choosing used parts, it is important to remember these specialized components require careful installation. This part is ideal for those seeking an economical solution without compromising functionality and safety.

Add this crucial part to your cart for your Peugeot 206 or 206+ and enjoy peace of mind knowing your brakes are in optimal condition. It’s just a few clicks away!

This ABS ECU (electronic control unit) and pump assembly is a direct-fit unit for Peugeot 206 models equipped with the 1.4 HDi 50 kW engine. Supplied with the wiring harness, it matches original PSA/ATE specifications and is commonly referenced by part numbers such as 9652342980 and 10.0207-0036.4. Customers often search by these codes, so this listing includes the most relevant references to help you find the correct unit quickly.

Key Features

• Complete ABS control module and hydraulic pump assembly (ATE style)
• Includes wiring harness for straightforward installation
• Direct replacement for compatible Peugeot 206 1.4 HDi vehicles
• Identified by multiple PSA/ATE part codes for easy lookup

Fitment And Application

Designed for Peugeot 206 1.4 HDi 50 kW. Compatible with PSA platforms using ATE ABS units. Always verify part numbers against your vehicle VIN or the unit currently fitted to ensure correct match.

Replacement And Installation Notes

Replacement should be carried out by a qualified technician or an experienced DIY mechanic. Typical installation steps include disconnecting the battery, removing the old ABS unit and pump assembly from the engine bay (usually mounted to the brake servo or inner wing area), transferring any required brackets or sensors, connecting the supplied wiring harness, and securely mounting the unit. After mechanical installation, it is necessary to bleed the brake system thoroughly to remove air from the hydraulic circuit. A diagnostic tool (for example PSA DiagBox or a compatible OBD2/ABS scanner) may be required to clear fault codes and, in some cases, to configure or adapt the new ABS module to the vehicle.

Common Failure Modes And Maintenance

ABS modules can fail due to electrical faults, corrosion of electrical connections, moisture ingress, or wear of the hydraulic pump motor and internal valves. Symptoms include ABS warning light illumination, loss of ABS function, unusual brake pedal feel, or persistent fault codes related to wheel speed sensors or pump circuits. Regular inspection of connectors and brake hydraulics helps reduce risk of premature failure.

Why Buy This Unit

This listing includes the wiring harness and references multiple manufacturer codes, making it a practical choice for workshops and DIY enthusiasts who need a reliable replacement that fits directly without major modifications. Including the correct part codes in your search improves the chance of immediate compatibility.

Technical Information

• Manufacturer: PSA (Peugeot/Citroën) / ATE
• Model: Peugeot 206 1.4 HDi 50 kW
• Product Codes: 9652342980, 10.0207-0036.4, 10.0970-1114.3
• Other Numbers: 4541V5, 4541V6, 1682608780, 4541RW, 4542J8, 4542Z0, 4541J9

Please verify the part numbers and connector types against your vehicle before purchase. If you are unsure about coding or diagnostic steps after installation, consult a professional workshop with PSA diagnostic capability to ensure full system operation and safety.