Original used comfort control unit Siemens BSI F03-00 BG for Citroën C2, C3 and C3 Pluriel. It is a Body Systems Interface (BSI) unit that controls the comfort and body functions of the car and is key to the communication of the multiplex network in the car. Suitable as a replacement for a defective BSI – especially for cars of the 1st generation C2/C3, where the new part is already NFP (not supplied).

Key identification and OEM numbers
– Manufacturer/type: Siemens/VDO – BSI F03-00 BG
– PSA/OEM: 9649811580, 1650881980 (1650881980 = NFP)
– Siemens number: S118085100 H
– Written on the unit label: always compare the whole designation, especially F03-00 BG and S118085100H

Compatibility
– Citroën C2 (approx. 2003–2009)
– Citroën C3 I (approx. 2002–2009)
– Citroën C3 Pluriel (approx. 2003–2010)
Note: Compatibility may vary by trim level and year of manufacture. Before ordering, please compare the BSI label and part numbers with your original piece or check against the VIN.

What the BSI controls and the typical symptoms of the defect
– Functions: central locking, direction indicators and lighting, wipers and washers, on-board network, communication with the instrument panel, immobilizer, comfort functions.
– Manifestations of defective BSI: spontaneous switching of wipers/lights, central failure, problems with diagnostics communication, random errors of comfort elements, battery discharge, engine not starting (IMMO).

Technical information
– Network: multiplex VAN/CAN depending on the vehicle equipment
– Location: interior – fuse box under dashboard (driver’s side)
– Design: integrated relays and fuses, multiple connectors
– Index: F03-00 BG (important for HW/SW compliance)

Assembly and coding – important
– BSI is paired with the car (VIN, immobilizer, equipment configuration). After replacement, adaptation is necessary.
– Options:
– Clone data from the original drive (EEPROM/flash transfer) – recommended if the old BSI is readable.
– Coding “to virgin” and subsequent pairing with PSA diagnostics (Lexia/PP2000/DiagBox).
– Without proper adjustment, the car usually won’t start. We recommend assembly and programming by an experienced car electrician/PSA diagnostician.

Why choose this part?
– Genuine PSA/Siemens part – correct compatibility and quality
– Replacement for numbers 9649811580 and 1650881980 (the new part is already NFP)
– Ideal solution for fixing frequent BSI glitches on C2/C3/C3 Pluriel

Search and Verification Tip
– Search and compare by: “BSI F03-00 BG”, “S118085100H”, “9649811580”, “1650881980”, “Citroën C3 BSI”, “Citroën C2 BSI”.
– Always check that the label and connectors match your original part before ordering.

This is an original used car part. The condition and design corresponds to the photos and markings on the label. For problem-free installation, we recommend professional coding and check compatibility in advance according to VIN and part numbers.

This Siemens BSI (Body Systems Interface) comfort control unit is a direct-fit electrical control module used on early Citroën C3 and C2 vehicles. It centrally manages convenience and body functions such as central locking, interior and exterior lighting logic, indicator/wiper interplay, remote locking, and communication with other vehicle modules via the vehicle network. The unit is commonly searched for by reference numbers and part codes, so see the Technical Information section below for full cross-references.

For professional technicians and DIY mechanics, this BSI offers a practical replacement option when owners report intermittent electrics, non-functioning central locking, erratic lighting behavior or complete loss of certain comfort functions. Replacing the module restores centralised control of multiple circuits and often cures symptoms that otherwise appear unrelated.

Technical Information

• Manufacturer: Siemens
• Model: Citroën C3, Citroën C2 (up to 2004)
• Product Codes: 9652474380, S118085300K, F01-00
• Additional Numbers: 1650882080, 1650881980

Function And Typical Symptoms

The BSI acts as the vehicle’s comfort control module, coordinating inputs from switches and sensors and driving actuators for lighting, central locking, interior lights, wipers and other convenience features. Typical symptoms of a failing BSI include:

• Intermittent or complete loss of central locking or alarm functions
• Erratic exterior or interior lighting (flicker, failure, or lights behaving incorrectly)
• Wipers or indicators operating unpredictably
• Multiple unrelated electrical faults appearing simultaneously

Installation Recommendations

• Disconnect the negative battery terminal before starting work to avoid short circuits and potential damage to the new module.
• Access the BSI by removing the appropriate trim panels; take care with connectors and retainers. Protect connectors from contamination and ensure pins are straight and clean before reconnection.
• After mechanical installation and reconnection, professional diagnostic equipment is typically required to perform module initialization, version checks and any necessary coding or synchronization with the vehicle immobilizer and keys.
• Replace any damaged fuses or connectors found during installation. Always follow manufacturer torque and mounting instructions for secure fitting.

Why This Part Fails Most Often

BSI units commonly fail due to environmental and electrical stress rather than mechanical wear. The most frequent causes are:

• Water ingress or moisture condensation causing corrosion on circuit boards or connectors
• Electrical surges, poor grounding or intermittent power supply leading to component damage
• Connector corrosion or damaged wiring causing shorts or erratic signals
• Ageing and thermal cycling that can create cracked solder joints or degraded electronic components

Typical lifetime depends on vehicle use and conditions; under normal conditions the unit can last many years, but exposure to moisture or repeated electrical faults will shorten service life.

Notes For Buyers

Search for this unit using the part numbers listed above (9652474380, S118085300K, 1650882080, 1650881980, F01-00) to ensure correct fitment. Professional installation and diagnostic programming are recommended to restore full vehicle functionality and to synchronize immobilizer and convenience settings after replacement.

This used automotive part offers a cost-effective solution for both professional mechanics and DIY car enthusiasts seeking reliable replacement components. Its precise compatibility with the listed Citroën and Peugeot models ensures seamless integration and proper operation of all BSI-related systems.

BSI modules like this one typically require replacement over time due to natural wear of electronic components or external factors such as moisture and temperature fluctuations. Common symptoms indicating the need for replacement include central locking malfunctions and irregular errors appearing on the vehicle’s onboard computer.

Investing in this Siemens BSI F01-00 HG module helps prevent more significant electronic issues within your vehicle and restores full functionality to interconnected systems. Each part sold is carefully inspected and ready for installation, providing assurance of performance at a fraction of the price of new units.

Explore the benefits of restoring your vehicle’s reliability and comfort with this essential control module.

Technical Information:

Manufacturer: Siemens
Model: Citroën C2, C3, C3 Pluriel; Peugeot 1007
Product Codes: 9650585680, S118085300 J, 1650881980
Additional Numbers: NFP

Are you looking for a reliable and proven auto part for your Citroën vehicle? With our Siemens BSI F02-00, which is compatible with Citroën C2 and C3 models, you will receive the quality and functionality you expect from an original part. This product is an ideal choice for mechanics or DIY repairers who value reliability and efficiency.

As this is a used part, it comes with all the technical specifications and functions required for your vehicle. The part has been carefully inspected and is offered in excellent working condition. Ensure code compatibility before purchase to guarantee alignment with your vehicle.

Technical Information:
Manufacturer: Siemens
Model: Citroën C2, Citroën C3
Product Codes: 9652474480 S118085200 J, 1650881980
Additional Numbers: NFP

This comfort control unit (BSI) is designed to integrate various electronic systems of the vehicle for smooth and efficient operation. Typically located within the vehicle’s interior, it manages functions such as lighting, door locking, or alarms, making this part essential for the proper functioning of the car.

Before purchasing this part, we recommend checking all information and ensuring the product fits your vehicle’s model. This step is crucial to avoid potential compatibility discrepancies and to ensure your Citroën operates like new.

Thanks to high-quality materials and precise construction, this auto part is durable and will meet your expectations in all aspects. Experience the outstanding features of this product and give your car what it deserves.

Designed for ease of installation, the Siemens BSI F01-00 HG can be replaced by following the vehicle’s service manual instructions. Regularly inspect this component, as it can fail due to electrical issues, wear over time, or exposure to extreme weather conditions.

The BSI (Built-in Systems Interface) facilitates communication between various vehicle systems, enhancing features such as lighting control, window operation, and various other electronic functions that improve driving comfort.

Technical Information

• Manufacturer: Siemens
• Model: BSI F01-00 HG
• Product Codes: 9649811380, 1650881980
• Additional Numbers: S118085300 I, NFP

As a vital part of the vehicle’s electrical system, the BSI (Body System Interface) is responsible for controlling functions such as lighting, windows, and other electronic features, ensuring they operate seamlessly. Regular issues with these units often arise due to electrical surges, wear and tear over time, or faults in other connected systems, which can lead to malfunctioning of various electronic components in your vehicle.

Replacing the BSI unit can significantly improve your vehicle’s functionality and reliability. It is recommended to check the BSI unit periodically and replace it whenever you encounter symptoms of malfunction, such as erratic operation of electrical features or warning lights on the dashboard.

Technical Information

• Manufacturer: Siemens
• Model: BSI F02-00 MG
• Product Codes: 9650585780, S118085200
• Additional Numbers: 1650881980