This seat belt buckle holder is designed for the Citroën C3 II (A51) and secures the buckle assembly for the front driver and passenger seats. It provides a direct replacement for damaged or worn bracketry and restores correct buckle positioning for safe and comfortable belt use. Commonly searched by part numbers 9687393180 and 8975SY, this durable FXX black finish bracket fits the original mounting points and matches the interior trim.

Function And Fitment

The holder secures the seat belt buckle to the seat structure, ensuring the buckle is correctly positioned and stable during normal use and in the event of a collision. It is intended for front seats (driver and passenger) on Citroën C3 II (A51) models. The part locates to the seat frame using factory mounting points and is compatible with the standard buckle assemblies used on these models.

Mounting Recommendations

• Before starting work, follow standard safety procedures. If the vehicle is equipped with seat belt pretensioners or airbags, disconnect the battery and wait the manufacturer-recommended time to avoid accidental deployment.
• Slide the seat fully back (or forward) to gain access to the mounting area, then remove any trim panels covering the seat base.
• Unbolt the old holder from the seat frame (typically Torx/hex bolts). Keep original fasteners if they are undamaged; replace corroded or deformed bolts with equivalent grade fasteners.
• Transfer the buckle assembly to the new holder if required, then fit the new bracket to the seat frame and torque fasteners to the vehicle manufacturer specification.
• Reinstall trim panels and check buckle function: the latch should engage smoothly and return to the upright position without binding.
• Perform a final visual inspection and, if battery was disconnected, reconnect and check that any seatbelt warning or airbag indicators behave normally.

Why This Part Typically Fails

Failure of the buckle holder usually results from mechanical damage (e.g., impact in a collision), plastic fatigue or embrittlement from long-term exposure, heavy or improper use, or corrosion of mounting hardware. Accidental loads, knocks when entering/exiting the vehicle, and wear from repeated buckle insertion can also deform or crack the bracket. Replacing a compromised holder is important because a loose or misaligned buckle can reduce the effectiveness of the restraint system.

Technical Information

• Manufacturer: Stellantis (Citroën)
• Model: Citroën C3 II (A51) – Front Driver And Passenger Seat
• Product Codes: 9687393180
• Other Numbers: 8975SY

Notes For Mechanics And DIY Enthusiasts

When fitting this part, ensure correct alignment to avoid stress on the buckle or cable routing. Use appropriate tools and replacement fasteners if original bolts show signs of corrosion. After installation, verify buckle engagement and seat belt retraction. If the vehicle has pretensioners or related safety systems, consider inspection by a qualified technician to confirm system integrity following any incident that damaged the original bracket.

This high-quality retractor holder is an original-fit replacement designed for rear seats on Citroën C3 II (A51) and DS3 models. Ideal for professional workshops and experienced DIY enthusiasts, the part restores secure anchoring of the seat belt retractor to the seat structure. Commonly searched by the OE code 98019948XX, this component delivers correct alignment and reliable operation after installation.

Function And Benefits

The retractor holder secures the seat belt retractor to the seat frame, ensuring the belt webbing winds and locks correctly during normal use and in the event of a collision. A correct-fit holder maintains the retractor’s geometry, prevents unwanted movement, and helps the restraint system perform as intended. Benefits include OEM compatibility, correct mounting points, and a factory finish (FXX – Black) matching original interior trim.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C3 II (A51), DS3
• Product Codes: 98019948XX
• Additional Numbers: –

Replacement And Installation Recommendations

• Work Recommended For: Qualified technicians or experienced DIYers with access to basic hand tools and a workshop manual.
• Preparations: Remove rear seat cushion and surrounding trim to access the retractor assembly. Keep track of clips and screws to avoid rattle or misalignment after reassembly.
• Safety: If the vehicle is equipped with a belt pretensioner or pyrotechnic components, follow manufacturer safety procedures. Disconnect the battery before starting work and wait the manufacturer‑specified time to reduce the risk of accidental deployment.
• Removal: Unbolt the old retractor holder from the seat frame, inspect the retractor and mounting points for damage or corrosion, and clean mating surfaces.
• Installation: Fit the new holder in the original position, hand-start bolts, then tighten to the manufacturer’s torque specification (refer to the workshop manual). Ensure the retractor operates smoothly and the belt webbing runs without obstruction.
• Post-Installation Check: Verify free spooling and locking action of the belt, correct routing, and that trim pieces are reinstalled without pinching the webbing.

Why The Part Fails Most Often

• Corrosion Or Rust: Prolonged exposure to moisture can corrode mounting points and fasteners, leading to loosening or breakage.
• Mechanical Wear Or Fatigue: Repeated use and vibration can wear fixing points or plastic inserts, causing play or failure.
• Impact Damage: After a collision the holder or its mounting can deform, compromising belt geometry and function.
• Foreign Objects And Contamination: Debris trapped in the retractor area can hinder movement and stress the holder over time.

Fitment And Search Tips

Designed for direct replacement on Citroën C3 II (A51) and DS3 rear seat applications. The OE reference 98019948XX is commonly used by professionals when searching for the correct spare part. Always inspect the existing mounting area and retractor for damage before fitting a new holder.

Final Notes

Replacing a damaged or corroded retractor holder restores correct seat belt alignment and contributes to overall occupant safety. If the belt retracts poorly, locks unexpectedly, or shows visible damage, replace the holder and associated components as required. When in doubt, consult the vehicle’s workshop manual or a professional technician to ensure safe and correct installation.