This replacement passenger-side seat belt buckle bracket (often searched under part numbers 8975AV or 8973QY) is designed for Citroën C8 and Peugeot 807 models. The unit includes the buckle mounting and a latch switch for the seat-belt alarm/occupant-detection circuit. Built to OEM fitment standards, it restores secure latching, reliable buckle sensing and correct alarm/warning lamp behaviour after failure or damage.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C8, Peugeot 807
• Product Codes: 8975AV, 8973QY
• Other Numbers: Not specified
• Color: FXX Black
• Side: Passenger (Front)
• Feature: Includes alarm/latch sensor

Function and Benefits

The buckle bracket secures the seat-belt latch and houses the microswitch that tells the vehicle whether the belt is fastened. A properly working unit ensures the seat-belt warning alarm and related safety logic operate correctly. Replacing a faulty buckle bracket restores safe restraint operation, prevents false alarm warnings, and ensures the seat-belt is held positively under load.

Installation Recommendations

• Always disconnect the vehicle battery before starting work to avoid short circuits and protect vehicle electronics.
• Remove the appropriate trim panels and seat fixings to gain access to the buckle mounting. Use proper trim tools to avoid damaging interior panels.
• Unbolt the old bracket, carefully disconnect the electrical connector for the buckle switch, and remove the unit.
• Fit the new bracket in the correct position, connect the electrical connector securely, and tighten mounting bolts to the manufacturer’s torque specification.
• Reinstall trim and seat components, reconnect the battery, and verify that the seat-belt buckle latches smoothly and the seat-belt warning/alarm operates as intended.
• Avoid applying lubricants to the sensor contacts. If connectors show corrosion, clean or replace as needed to ensure reliable operation.
• If in doubt about correct torque values or electrical checks, follow manufacturer repair procedures or consult service documentation.

Why This Part Most Commonly Fails

• Mechanical Wear: Repeated latching/unlatching and debris ingress can wear the latch mechanism or switch over time.
• Contamination and Corrosion: Dirt, liquids or corrosion can impair the microswitch or connectors, causing intermittent or permanent faults.
• Impact Damage: Seat-belt mounts and buckles are vulnerable in collisions; visible deformation or bent brackets require replacement.
• Electrical Faults: Broken wiring, damaged connectors or failed microswitches can prevent correct alarm/warning signals.
• Aging: Plastic components, clips and wiring harnesses degrade with age, particularly in high-use or high-humidity environments.

Practical Tips for Mechanics and DIYers

• Search by product codes 8975AV or 8973QY for fast identification and ordering.
• Inspect surrounding seat-belt components (anchor bolts, webbing, retractor) when replacing the buckle bracket to ensure overall system integrity.
• After installation, perform a functional check: buckle/unbuckle several times, confirm alarm/warning light behavior, and visually inspect for secure mounting.

Compatibility

Fits Passenger Side for Citroën C8 and Peugeot 807 models. Commonly referenced by part numbers 8975AV and 8973QY. Verify fitment against vehicle model and mounting pattern before installation.

High-quality replacement seat belt intended for professional workshops and experienced DIY mechanics who maintain Stellantis MPV interiors. This center rear belt restores proper occupant restraint and is commonly sought under the part codes 14008311XX or 8974A0. The black FXX webbing integrates with the vehicle’s original mounting points and trim for a factory-like appearance and reliable performance.

Technical Information

• Manufacturer: Citroën / Peugeot (Stellantis)
• Model: Citroën C8, Peugeot 807
• Product Codes: 14008311XX, 8974A0
• Other Numbers: Color FXX – Black; Position: Center Rear Seat, Second Row (behind driver and front passenger)

Installation Recommendations

• Follow Safety Procedure: Disconnect the negative battery terminal and wait the manufacturer-recommended time before working near SRS components or pretensioners.
• Access: Remove interior trim panels around the B-pillar and rear seat base to expose the belt retractor and anchor bolts.
• Removal: Unbolt the lower anchor and seat belt mounting hardware, then disconnect any electrical connector if a pretensioner is present.
• Fitting: Fit the new belt assembly to the original mounting points. Tighten all bolts to the manufacturer torque specification and secure any electrical connectors for pretensioners.
• Checks After Fitment: Verify smooth retraction and extension, confirm the locking mechanism engages under a sharp pull, and ensure buckle latches reliably. Refit trim panels without pinching the webbing.

Why This Part Fails Most Often

• Wear And Abrasion: Frequent use, contacts with seat edges or rough surfaces cause webbing fraying and weakening over time.
• Contamination: Dirt, grit, and moisture can impede smooth retraction and accelerate wear of the mechanism.
• Pretensioner Deployment: Deployment in a collision renders the belt assembly unusable and requires replacement.
• Corroded Or Damaged Mountings: Corrosion or impact damage to anchor bolts and brackets can compromise belt function.
• Retractor Jamming: Internal spring or locking mechanism failure due to age, debris, or mechanical fault prevents proper operation.

This seat belt is a direct-fit solution for the specified center rear position on Citroën C8 and Peugeot 807. Because these belts are often searched by their product codes, listing 14008311XX and 8974A0 increases findability for workshops and DIYers looking for a reliable replacement.

Are you looking for a reliable safety belt for your Citroën C8 or Peugeot 807? Our selection of quality used auto parts includes safety belts that ensure safety for you and your passengers. This specific model is designed for the right and left rear seats in the third row of Citroën C8 and Peugeot 807 vehicles, meeting the most specific requirements of both models.

Our safety belt for Citroën and Peugeot has been carefully selected to meet high safety and quality standards. Its installation in your vehicle is straightforward and simple, which is appreciated by both professional mechanics and DIY enthusiasts. With its robust construction and durable materials, this part will maintain its high functionality and reliability even after many years of use.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: Citroën C8, Peugeot 807
• Product Codes: 14996410XX
• Additional Numbers: N/A

By purchasing this safety belt, you will receive a product that has undergone thorough inspection and is ready for installation. Not only will you ensure safety in your vehicle, but you will also save on the cost of buying a new part. Suitable for repairs and maintenance, this safety belt represents an economical and effective solution for your automotive needs.

Enhance the safety of your vehicle with a used but excellent safety belt specifically designed for Citroën C8 and Peugeot 807 models. This part is an ideal choice for anyone looking for quality at a reasonable price. Ensure your ride is safe with our proven safety belt. Shop with us to get not only an excellent product but also professional service and fast delivery.

This used OEM seat belt assembly is designed for the rear outboard seats of Citroën C8 and Peugeot 807 models. Supplied in Black (Color Code FXX), the belt fits both Right And Left rear positions (behind the Driver And Front Passenger) and matches original mounting points for direct replacement. Ideal for professional workshops and skilled DIYers looking for a correct-fit replacement by part number (see Product Codes below).

Key Benefits

Reliable OEM Fit: Manufactured for Stellantis Group vehicles and suitable for Citroën C8 and Peugeot 807. Durable Webbing: Standard black webbing (FXX) that blends with original interior. Easy Replacement: Direct bolt-on fitment to existing anchors when installed according to manufacturer torque and safety procedures.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C8, Peugeot 807
• Product Codes: 14910150XX, 14004997XX, 8974RP
• Other Numbers: 8975A0, 8975RP
• Color: FXX – Black
• Position: Rear Outboard Seats (Right And Left)

Installation Recommendations

• Prepare: Work On A Level Surface And Have Proper Hand Tools, Torque Wrench, And Wheel Chocks.
• Safety First: If The Vehicle Is Equipped With Seat Belt Pretensioners Or SRS Components, Disconnect The Battery And Wait The Manufacturer-Specified Time Before Starting Work.
• Remove Trim: Carefully Detach Interior Trim Panels To Access Anchors And Retractor Mounts Without Damaging Clips.
• Unbolt Old Assembly: Remove Bolts Securing Retractor, Anchor, And Buckle. Keep Hardware If Reuse Is Allowed By Manufacturer; Otherwise Replace With New Bolts As Required.
• Fit New Assembly: Position Retractor And Anchors To Original Points, Ensure Webbing Is Not Twisted, Then Tighten Bolts To Manufacturer Torque Specifications.
• Function Check: Verify Free Pulldown And Locking Action Under A Sharp Pull. Check Buckle Engagement And Release.
• Final Steps: Reinstall Trim Panels, Reconnect Battery (If Disconnected), And Perform A Visual And Functional Check Before Returning Vehicle To Service.

Why This Part Fails Most Often

• Webbing Wear And Fraying: Continuous Use, Sunlight Exposure, Or Abrasive Contact With Seat Edges Can Damage The Belt Webbing Over Time.
• Retractor Malfunction: Dirt, Corrosion, Or Internal Spring Failure Can Cause The Retractor To Stick Or Fail To Lock Properly.
• Pretensioner Deployment: In Vehicles That Use Pyrotechnic Pretensioners, A Crash Event Will Deploy The Unit, Rendering The Belt Unsafe And Necessitating Replacement.
• Anchor Point Corrosion Or Bolt Damage: Rust Or Previous Accident Damage Can Weaken Mounts, Causing The System To Be Unsafe.

Fitment And Service Notes

Always Replace Seat Belts That Show Significant Webbing Damage, Retractor Locking Issues, Or Evidence Of Pretensioner Deployment. After Installation, Confirm Correct Operation Of The Locking Mechanism And That The Webbing Retracts Smoothly Without Twists. Use Correct Torque Values For Mounting Bolts And Replace Any Stretched Or Damaged Fasteners.

Common Search Terms

Citroën C8 Seat Belt, Peugeot 807 Seat Belt, Rear Seat Belt C8 807, 14910150XX, 14004997XX, 8974RP, Black Seat Belt FXX, OEM Seat Belt Replacement

This genuine-style rear seat belt is a direct-fit replacement for Citroën C8 and Peugeot 807 models, suitable for both right- and left-hand rear seating positions. Ideal for professional workshops and DIY mechanics, the belt restores occupant restraint performance and interior appearance. Commonly searched by part numbers 14008311XX, 14844310XX or 8974RP, this assembly is a practical spare part when a webbing, retractor or buckle is damaged or after collision deployment.

Key Features

• Direct fit for Rear Right And Rear Left Seats On Citroën C8 And Peugeot 807
• Color FXX (Black), Matching Factory Interior Finishes
• Complete Assembly: Webbing, Retractor And Buckle (depending On Vehicle Specification)
• Supplied With OEM-Style Fixing Points To Replace Worn Or Damaged Units

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C8; Peugeot 807
• Product Codes: 14008311XX; 14844310XX; 8974RP
• Other Numbers: Color Code FXX – Black

Installation Recommendations

Installation should be performed by a qualified technician or an experienced DIY mechanic following manufacturer safety practices. General steps:

• Disconnect The Battery And Wait At Least 10 Minutes Before Starting Work To Reduce Risk From Airbag System Capacitors.
• Remove Interior Trim Panels To Access Seat Belt Anchor Points And Retractor.
• Unbolt The Old Assembly From Its Anchors And Carefully Disconnect Any Electrical Connectors If The Belt Includes A Pretensioner Or Sensor.
• Fit The New Belt Assembly Ensuring The Webbing Is Correctly Routed Through Guides And Retractor Is Properly Seated.
• Tighten Fasteners To The Manufacturer’S Specified Torque (Refer To Vehicle Repair Manual).
• Check Free Movement Of The Webbing, Correct Locking Under Sudden Pull, And Secure Latching Of The Buckle.
• Reassemble Trim Panels And Perform A Functional Check With Doors Closed.

Why This Part Fails Most Often

Seat belts typically fail or require replacement for the following reasons:

• Wear And Abrasion Of The Webbing Due To Long-Term Use Or Foreign Objects (Sharp Edges, Sand, Pet Claws).
• Contamination Or Corrosion Causing Retractor Jamming Or Sluggish Operation.
• Pretensioner Activation During A Collision (Pretensioners Are Single-Use And Must Be Replaced After Deployment).
• Buckle Failure From Dirt, Spills Or Mechanical Damage Preventing Secure Latching.
• Anchor Bolt Corrosion Or Thread Damage Compromising Mounting Integrity.

Practical Tips

Always Compare The Supplied Product Codes With The Existing Unit On The Vehicle Before Installation. Inspect Webbing For Cuts Or Chemical Damage And Verify The Retractor Locks Under A Sharp Tug. Replace The Entire Assembly If Any Component Shows Signs Of Impact Or Irreversible Damage.

Compatibility And Search Tips

Search Engines And Spare-Part Catalogs Often Return This Item Under The Part Numbers 14008311XX, 14844310XX Or 8974RP. Use These Codes Alongside Vehicle Model Names (Citroën C8, Peugeot 807) To Improve Findability.

High-quality replacement seat belt designed for the third row of Citroën C8 and Peugeot 807 vehicles. This unit is intended for professional workshops and experienced DIY mechanics who require a reliable, direct-fit solution for left- or right-side third-row seating. The belt is commonly referenced by the original product codes listed below, making it easy to locate in parts catalogs and order systems.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C8; Peugeot 807 — Third-Row Left/Right
• Product Codes: 14844310XX, 14005557XX
• Additional Numbers: 8974RK

Fitment And Function

This assembly fits the third-row seating positions on Citroën C8 and Peugeot 807 models. It provides the primary occupant restraint for rear passengers and is designed to lock under sudden deceleration to restrain forward movement. Typical third-row belts for these MPVs are lap-and-shoulder (three-point) systems with a retractor mechanism to maintain appropriate webbing tension during normal use.

Installation Recommendations

• Remove interior trim panels to access mounting points; ensure correct routing of the belt webbing through trim guides.
• Unbolt the original assembly from its anchor points and fit the replacement in the same orientation. Use mounting hardware specified by the manufacturer and tighten to factory torque values.
• If The Vehicle Is Equipped With Pyrotechnic Pretensioners Or SRS Components, Disconnect The Battery And Follow The Manufacturer’s Safety Procedures Before Work — Treat The System As An SRS Component.
• Inspect Anchor Points, Bolts And Surrounding Structure For Damage Or Corrosion; Replace Any Compromised Fasteners.
• After Installation, Check Belt Retraction And Locking Behavior: The Webbing Should Run Smoothly And Lock Under A Sharp Pull.
• Follow The Vehicle Manufacturer’s Instructions For Final Checks And Any Required Adjustments.

Most Common Failure Reasons

• Wear And Abrasion Of Webbing Caused By Frequent Use Or Contact With Sharp Edges.
• Contamination And Dirt In The Retractor Mechanism Leading To Sticking Or Slow Retraction.
• Corroded Or Loose Mounting Points That Compromise Belt Performance.
• Pretensioner Activation During A Collision, Rendering The Belt Nonfunctional And Requiring Replacement.
• Mechanical Failure Of The Locking Mechanism Due To Age Or Internal Component Degradation.

Why Choose This Part

Using a correctly coded replacement belt that matches the original product numbers ensures correct fitment, reliable function and straightforward installation. For workshops and skilled hobbyists, this part reduces vehicle downtime and restores occupant restraint performance in the third row.

Advice For Professionals

Always Verify Fitment By Cross-Referencing The Product Codes Shown Above With Your Parts Catalog. Replace Any Mounting Hardware If Recommended By The Manufacturer And Perform A Full Functional Check After Installation.

High-quality replacement seat belt designed for the right front (passenger) position in Citroën C8 and Peugeot 807 models. This part is ideal for professional workshops and experienced DIY mechanics who need an OEM-fit safety component. The belt is commonly referenced by part numbers 14007783XX and 8974XE, so customers often search using these codes when looking for a direct replacement.

Features And Benefits

Provides a direct-fit installation without modifications on compatible vehicles. Designed to meet original equipment specifications for fit and function, ensuring reliable webbing retraction and locking performance. Suitable for restoring occupant restraint functionality after wear, contamination, or mechanical failure of the original belt (excluding belts that have been deployed in a collision — see Replacement Guidance).

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C8; Peugeot 807
• Product Codes: 14007783XX, 8974XE
• Other Numbers: 14007783 (variable suffixes may apply)

Installation And Recommendations

• Safety First: Work In A Well-Lit Area And Wear Appropriate PPE. Before starting, disconnect the negative battery terminal and wait at least 2 minutes to reduce the risk of accidental SRS/pretensioner activation.
• Removal: Remove necessary trim panels to access mounting bolts. Unbolt the lower anchor(s), shoulder guide(s), and retractor mounting bolt(s) following the vehicle repair manual sequence.
• Replacement: Fit the new belt ensuring correct webbing routing and that the retractor is mounted in the correct orientation. Tighten all fasteners to the torque values specified in the manufacturer service manual.
• Function Check: Verify smooth extension and retraction, and confirm the locking mechanism engages under a sharp pull. Ensure buckle latches securely and releases normally.
• Final Steps: Refit trim, reconnect the battery, and perform any required system checks described in the vehicle documentation. Do not use the vehicle for passenger transport if the belt shows any abnormal behavior after installation.

Replacement Guidance

Replace the seat belt immediately if webbing is frayed, cut, contaminated with corrosive substances, if the retractor fails to operate, or after deployment of a pretensioner in an accident. A safety belt is a life‑safety component — do not attempt to repair damaged webbing or internal mechanisms.

Common Failure Causes

• Mechanical Wear: Repeated use causes webbing abrasion and fraying, particularly where it rubs on trim or seat edges.
• Contamination: Dirt, grit or liquids can jam the retractor or degrade the webbing and buckle mechanism.
• Corrosion: Moisture ingress to mounting points or internal components can lead to binding or failure to retract.
• Pretensioner Deployment: A belt that has been involved in a collision and whose pretensioner has fired must be replaced.
• Incorrect Installation: Improper routing or loose fasteners can prevent correct operation and reduce occupant protection.

This seat belt is aimed at mechanics and competent DIYers who understand vehicle restraint systems and follow manufacturer procedures. The part is frequently searched by its product codes (14007783XX, 8974XE), so using these references helps find the correct replacement quickly.

High-quality replacement seat belt assembly designed for the right front (passenger) seat of Citroën C8 and Peugeot 807 models. This seat belt restores occupant restraint and retraction performance, helping to ensure vehicle safety after wear, contamination, or following partial system faults. Ideal for professional workshops and experienced DIY mechanics searching by part number (14844280XX / 8974XE).

Key Features

– Complete belt assembly with retractor and shoulder webbing configured for the front passenger position.
– Direct-fit for Citroën C8 and Peugeot 807 (right front seat).
– Commonly sought under OE codes 14844280XX and 8974XE—useful for quick identification in parts catalogs and search engines.
– Restores smooth retraction, locking on sudden deceleration, and proper belt routing for occupant protection.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C8; Peugeot 807
• Product Codes: 14844280XX; 8974XE
• Other Numbers: Common dealer and catalog references for the above codes

Function And Service Notes

The seat belt assembly restrains the passenger during a collision and provides pre-tensioning and load-limiting functions where fitted. The retractor contains a locking mechanism that engages under rapid deceleration to prevent occupant movement. Over time, webbing wear, contamination, mechanical damage or internal retractor faults can reduce effectiveness. After any collision where the restraint system has been activated, the belt assembly should be inspected and replaced if any deformation, fraying, or deployment evidence is present.

Why This Part Fails Most Commonly

– Webbing Wear And Contamination: Dirt, oil, or chemicals weaken fibers and reduce smooth retraction.
– Mechanical Jamming: Debris or corrosion inside the retractor can prevent free movement or cause false locking.
– Pretensioner Deployment: In vehicles fitted with pyrotechnic pretensioners, deployment during an accident renders the assembly unusable and it must be replaced.
– Anchor Bolt Corrosion Or Damage: Corroded or damaged mounting points compromise fixation and safety.

Installation Recommendation

– Disconnect The Battery: Always disconnect the vehicle battery and wait per manufacturer guidance before starting work to reduce the risk of accidental pretensioner activation or airbag faults.
– Remove Interior Trim Panels To Access Mounting Points: Carefully remove trim without damaging clips. Note routing of the webbing and trim fitment for correct reassembly.
– Unbolt And Replace Assembly: Remove lower and upper anchor bolts and the retractor mounting bolts. Fit the replacement in the same orientation and route the belt as original.
– Torque To Manufacturer Specification: Tighten bolts to the vehicle manufacturer’s specified torque values; use new fasteners if required by the manufacturer.
– Functional Check: Verify smooth retraction, correct locking under a sharp tug, and that no airbag or restraint system warning lamps remain on after reconnection.
– Professional Calibration: If the assembly includes electronic pretensioner components or the vehicle indicates restraint faults, diagnostics with a PSA-capable tool may be necessary.

Notes For Mechanics And DIYers

Searchable by OE codes 14844280XX and 8974XE, this part is commonly replaced during interior refurbishments, after accidents, or when retraction/locking faults occur. Inspect belts regularly for fraying, cuts, or chemical damage and replace immediately if any damage is present. Always follow Citroën/Peugeot workshop procedures when working on occupant restraint systems.

High-quality replacement seat belt assembly for the left front (driver) position on Citroën C8 and Peugeot 807 models. This direct-fit unit restores occupant restraint function after damage or wear and carries common OEM references 14007784XX and 8974XF, making it easy to find by part number. Designed for professional garages and experienced DIYers who need a reliable, vehicle-specific seat belt for safe, long-term use.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C8; Peugeot 807
• Product Codes: 14007784XX; 8974XF
• Other Numbers: 8974XF; 14007784XX

Function and Typical Use

The seat belt secures the occupant by restraining forward movement during sudden deceleration or collision. The assembly typically includes the webbing, retractor mechanism and buckle attachment points. Properly functioning belts are essential for airbag systems to perform as intended and for occupant safety in everyday driving and accident scenarios.

Replacement Procedure

Basic replacement steps for experienced technicians or competent DIYers:

• Disconnect the vehicle battery before starting work to avoid electrical hazards and to prevent unintended activation of restraint components.
• Remove interior trim panels to access belt anchor bolts and the retractor housing; keep fasteners organized for reassembly.
• Unbolt the anchor points and detach the old belt assembly from the retractor and buckle mounts.
• Install the new assembly in the correct orientation, secure all bolts and fasteners, and reinstall trim panels.
• Reconnect the battery and perform a functional check: ensure smooth webbing travel, correct locking under a quick pull, and secure buckle engagement.
• Always Follow Manufacturer Procedures And Torque Specifications During Installation.

Installation Recommendations

• Use the correct grade and length bolts; tighten to the manufacturer’s torque settings—if unknown, consult official service literature.
• Inspect mounting points and surrounding structure for deformation or corrosion; repair any damage before fitting the new belt.
• Do Not Reuse Bolts Or Components That Show Signs Of Stretch Or Damage.
• Some Vehicles May Have A Pretensioner Integrated In The Belt; If Present, Treat According To Manufacturer Guidance.

Why This Part Fails Most Often

• Deployment In A Collision: Belts And Pretensioners Often Require Replacement After An Accident.
• Wear And Age: Webbing Can Fray, Fade Or Lose Strength Over Years Of Use.
• Contamination: Dirt, Oils Or Chemicals Can Degrade Webbing And Retractor Mechanisms.
• Retractor Failure: Internal Springs Or Locking Mechanisms Can Seize Or Malfunction.
• Corrosion Or Damaged Mounting Points That Compromise Secure Anchoring.

Additional Notes

Searchable Part Numbers: Customers and workshops frequently look for this item by OEM codes 14007784XX and 8974XF. Replace seat belts that show visible damage or fail functional checks—never attempt repairs to webbing or locking mechanisms. Regular inspection as part of routine vehicle maintenance helps ensure occupant safety.

High-quality replacement safety belt designed for the left front (driver) position on Citroën C8 and Peugeot 807 models. This part corresponds to common OE references 14864390XX and 8974XF and is aimed at professional mechanics and experienced DIY enthusiasts who require a reliable, directly replaceable belt assembly. The belt restores occupant restraint function, meets original fitment points and mounting geometry, and is suitable for vehicles originally equipped with a 3-point seat belt system.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C8, Peugeot 807
• Product Codes: 14864390XX, 8974XF
• Additional Numbers: 14007784XX

Function And Description

The assembly is a 3-point driver seat belt with a retractor and inertia locking mechanism. It restrains the occupant during sudden deceleration and helps reduce movement in the event of a collision. Many original installations on these models incorporate a pretensioner and a load limiter to improve occupant protection; if the pretensioner has deployed in a prior event, the entire assembly must be replaced.

Installation Recommendations

Before starting work, take appropriate safety precautions. If the vehicle is equipped with a pretensioner, disconnect the negative battery terminal and wait at least 10 minutes to reduce the risk of accidental activation. Remove required trim panels to access the upper anchor, retractor and lower mounting bolts. Unbolt the anchor points and remove the old belt assembly. Install the new belt ensuring correct routing and alignment of the webbing, then torque all mounting bolts to the manufacturer’s specifications. After installation, check for smooth operation of the retractor and correct locking under sudden pulls. Inspect surrounding mounting points and trim for damage and replace fasteners if corroded or deformed.

Why This Part Typically Fails

• Wear And Abrasion: Repeated use can cause fraying or weakened webbing, especially where it rubs against trim or hardware.
• Contamination: Dirt, oils or chemicals can degrade webbing and internal mechanisms.
• Pretensioner Activation: In a collision the pyrotechnic pretensioner will fire and the belt must be replaced.
• Mechanism Seizure: Retractor spring or locking mechanism can stick due to corrosion, debris or long-term wear.
• UV And Ageing: Prolonged sun exposure can weaken webbing over many years.

Service Advice

Replace The Belt After Any Impact That Activates The Pretensioner Or If The Webbing Shows Cuts, Heavy Fraying, Burn Marks Or Stiffness. Always Verify Mounting Points And Fasteners For Structural Integrity. For Best Results Use Appropriate Torque Settings From The Manufacturer And Follow Repair Manuals For Trim Removal And Reassembly.