High-quality interior rearview mirror designed for direct replacement on Citroën and Peugeot vehicles. This mirror, commonly searched under part number 8149NA, restores clear rear visibility and maintains the original interior appearance. It is suitable for professional workshops and skilled DIY enthusiasts who perform routine interior replacements. The mirror comes in color code FBJ – LAMA to match original upholstery and trim finishes.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2, Citroën C3, Citroën C4, Peugeot 307, Peugeot 1007
• Product Codes: 8149NA
• Additional Numbers: Color Code FBJ – LAMA

Function And Description

The interior rearview mirror provides the driver with a clear central view of the traffic behind the vehicle. Depending on vehicle equipment, the mirror may be a simple manual unit or include integrated features such as auto-dimming, ambient lighting, or housing for sensors. This listed unit is supplied to match original mounting points and interior color.

Replacement Procedure

• Prepare The Vehicle: Park on a level surface and engage the parking brake. If The Mirror Has Electrical Connections (e.g., Auto-Dim Or Lighting), Disconnect The Battery Before Starting.
• Remove Trim: Carefully remove any overhead trim or plastic cover hiding the mirror mount to avoid damaging clips.
• Release Mirror From Mount: Depending On Mount Type, Slide The Mirror Off The Bracket Or Unscrew Fasteners. For Windshield-Mounted Mirrors With Adhesive Pads, Carefully Follow The Manufacturer Procedure To Remove The Adhesive Pad Without Damaging The Glass.
• Install New Mirror: Position The New Mirror On The Mount, Reconnect Any Electrical Connectors, And Secure Clips Or Screws Firmly. Replace Trim And Reconnect The Battery If Disconnected.
• Functional Check: Verify Mirror Position, Stability And Any Electrical Functions (Auto-Dim, Lights) Before Completing The Job.

Installation Recommendations

• Use Appropriate Tools: Plastic trim tools protect interior panels and clips during removal.
• Follow Manufacturer Procedures: For Windshield Adhesive Mounts Use Approved Adhesive Kits If The Mounting Pad Is Replaced.
• Handle Electrical Connectors With Care: Ensure Connectors Are Clean And Fully Engaged; Reconnect The Battery Only After All Connections Are Secure.
• Check Alignment: Adjust Mirror Position For Optimal Rear Visibility And Ensure Mounting Is Rigid To Prevent Vibration.

Why This Part Fails Most Often

• Impact Damage: Road Debris Or Minor Collisions Can Crack The Glass Or Break The Mount.
• Mounting Failure: Plastic Clips Or Adhesive Pads Can Degrade Over Time, Causing The Mirror To Loosen Or Fall Off.
• Moisture Ingress: For Mirrors With Electrical Components, Water Penetration Can Cause Malfunctions Or Short Circuits.
• Wear And Tear: Frequent Adjustments And Vibrations Can Cause Internal Mechanisms To Loosen, Leading To Unstable Mirror Position.

Often searched by part number 8149NA. Order this direct-fit interior mirror to restore factory appearance and safe rear visibility.

Are you looking for an original interior rearview mirror for Citroën or Peugeot with code 8149FF? We offer a used, fully functional OEM PSA part that fits perfectly and maintains the original interior appearance. This part is NFP (No Further Production) – new is no longer produced, so a quality used original is the best choice.

Key benefits
– Original PSA part: exact fit, no vibrations, original appearance
– Day/night version: convenient manual switching against glare
– Color FBJ – LAMA: light gray shade for matching interiors
– A cost-effective and proven alternative to a new part (NFP)

Technical information
– OE/PSA number: 8149FF (also listed as 8149.FF, 8149 FF)
– Design: internal rear-view mirror, mechanical day/night switching
– Colour/interior: FBJ – LAMA (light grey)
– Mounting: on a foot glued to the windshield (PSA standard); assembly by sliding/turning into the lock
– Electrical equipment: without electrochrome (without automatic dimming), without connector; does not serve as a rain/light sensor holder
– Package contents: mirror with foot mount; the glued foot is part of the windshield, not part of the part

Compatibility
– Citroën: C2, C3, C4 (selected versions and equipment)
– Peugeot: 1007, 307 (I)
Note: Different equipment may have a different design of the mirror (e.g. electrochromic). To be sure, check the match against part number 8149FF or VIN.

Condition and origin
– Used original PSA part, functionally tested
– Normal cosmetic signs of use possible; the condition corresponds to the photos in the product detail

Assembly tip
– When removing/installing, do not handle the metal/glued foot on the glass to avoid damaging the windshield.
– The mirror is placed on the foot and locked by clicking/turning. Assembly is a matter of minutes, without the need for electrical connections.

Frequently searched terms (SEO)
– interior mirror Citroën C2 C3 C4
– interior mirror Peugeot 307 1007
– interior/central day/night mirror
– original mirror PSA 8149FF, 8149.FF, FBJ LAMA, NFP

Not sure about compatibility? Email us the part number 8149FF or VIN – we’ll be happy to verify the correctness for free.

This interior rearview mirror is a direct replacement option for a range of Citroën and Peugeot models. Ideal for professional workshops and DIY mechanics, the unit matches original mounting points and product codes used by Stellantis, making it easy to find and fit. Commonly searched under codes 8148Y7, 8148KK and 8153LH, this mirror restores visibility, comfort and safety after damage or wear.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2, Citroën C3, Citroën C4; Peugeot 207, Peugeot 307, Peugeot 407, Peugeot 1007
• Product Codes: 8148Y7, 8148KK, 8153LH
• Additional Numbers: Not Available

Features And Benefits

• Direct Fit: Designed to match the original mounting interfaces on the listed Citroën and Peugeot models for a secure installation.
• Searchable By Code: Easily located in parts databases and search engines using OE codes 8148Y7, 8148KK or 8153LH.
• Practical Replacement: Restores proper rear visibility and the original look of the vehicle interior.
• Workshop Friendly: Suitable for both professional mechanics and experienced DIYers familiar with interior trim removal and basic electrical connectors.

Installation Recommendations

• Prepare Workspace: Park the vehicle on a level surface and protect interior trims. If the mirror has electrical functions (e.g., internal microphone, auto-dim or compass), disconnect the negative battery terminal before starting.
• Remove Trim: Carefully pry off the roof lining trim or plastic cover around the mirror mount using appropriate trim tools to avoid damage.
• Release Mirror: Depending on variant, release the mirror from the mounting button by unscrewing the retaining screw or sliding the mirror off the glued bracket. Disconnect any wiring harness gently.
• Mounting Button: If the windscreen mounting button is damaged or the mirror attaches to a glued plate, replace the button or use a suitable windshield adhesive rated for mirror mounts. Follow adhesive cure times before final assembly.
• Reconnect And Test: Reconnect the wiring, reattach trim pieces and, if the battery was disconnected, reconnect it and verify electrical functions (if present) and mirror adjustment.
• Tools And Consumables: Trim removal tools, Torx/Phillips screwdriver (depending on retaining fastener), windshield mirror adhesive (if replacing mounting button), and dielectric grease for connectors are recommended.

Why The Part Fails Most Often

• Impact Damage: Collision, slamming doors or objects striking the mirror are the most common causes of breakage.
• Mount Detachment: Old or degraded adhesive on the windshield mounting button can cause the mirror to detach, especially after temperature cycles and long-term UV exposure.
• Internal Wear Or Electrical Fault: Variants with auto-dimming or integrated electronics may fail due to moisture ingress, connector corrosion or electronic component wear.
• Mechanical Wear: Repeated adjustment, vibration and ageing of plastic parts or clips can lead to looseness or failure.

Service Tips And Notes

• Search By Code: Use OE codes 8148Y7, 8148KK or 8153LH when searching parts catalogues to ensure correct match.
• Replacement Parts: If the mirror was bonded to the glass and the mounting button is damaged, replace the button and allow adhesive to cure fully before attaching the new mirror.
• Professional Fitment: For vehicles with integrated sensors or advanced mirror electronics, consider installation by an experienced technician to ensure correct operation.

Description

High-quality interior rear-view mirror designed as a direct replacement for a range of Citroën and Peugeot models. This unit fits original mounting points and is ideal for professional workshops or competent DIY mechanics looking for a reliable OE-compatible mirror. Supplied under reference numbers commonly searched by technicians and parts buyers, the mirror restores clear rear visibility and, depending on variant, integrates with vehicle wiring for features such as interior lighting or automatic dimming.

Key Features

• Direct-fit replacement for specific Citroën and Peugeot models.
• OE Part Numbers Included For Quick Lookup And Ordering.
• Standard mounting for windscreen/bracket attachment; electrical connector present on variants with powered functions.
• Durable glass and housing designed for everyday driving conditions.
• Suitable For Workshop And Do-It-Yourself Installation.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C2, Citroën C3, Citroën C4, Citroën Xsara Picasso; Peugeot 1007, Peugeot 207, Peugeot 307, Peugeot 407
• Product Codes: 98044718XT, 8148Y7, 8148KK, 8153LH
• Other Numbers: 8148KK, 8148Y7, 8153LH, 98044718XT

Installation Recommendation

Before starting, prepare trim tools, screwdrivers and, where required, a small torque wrench. Typical replacement steps:

• Protect interior trim and glass. If the mirror has electrical functions, disconnect the vehicle battery before disconnecting any connectors to avoid short circuits.
• Remove any trim cover around the mirror base. Release the locking screw or clip that secures the mirror to the windscreen mount or base plate.
• Disconnect the electrical connector (if present) and remove the old mirror from its bracket. If the mirror is glued to the windscreen, follow the correct procedure for cutting off the old mount and cleaning the glass surface.
• Fit the replacement mirror onto the existing bracket or install the supplied mounting plate/adhesive kit as required. Reconnect electrical plug, secure fasteners to manufacturer’s specification and re-fit trim.
• Re-connect the battery and verify mirror functionality: manual day/night lever operation, auto-dimming (if fitted), interior lights or any integrated sensors.

For vehicles with glued mounting plates use a dedicated windscreen mirror adhesive kit and allow recommended curing time before driving. When in doubt about electrical variants, inspect the connector and wiring harness carefully and test functions after installation.

Why The Part Most Commonly Fails

• Physical Impact: Minor collisions, door impacts or heavy vibrations can crack the glass or snap the mounting bracket.
• Adhesive/Bracket Failure: Windshield-mounted mirrors can detach over time due to degraded adhesive or damaged base plates.
• Electrical Faults: Variants with auto-dimming, heating or integrated lights can suffer connector corrosion or internal electronic failure.
• Wear And Tear: Repeated adjustment, vandalism or aging plastic components lead to looseness and poor mirror stability.

Service Advice

There is no scheduled replacement interval—replace the mirror when visibility is compromised, the unit is physically damaged, or electrical functions fail. For workshop installations, always follow manufacturer torque and fastening specifications and check associated trim and windscreen mounts for damage when replacing the mirror.

This interior rearview mirror is a direct replacement designed for Citroën and Peugeot vehicles. It restores clear rear visibility and factory fitment for daily driving and workshop repairs. Product code 815340 helps technicians and DIY enthusiasts locate the correct part quickly.

Compatibility

Compatible Models: Citroën C2, Citroën C3, Citroën C4; Peugeot 307 (including 307 I) and Peugeot 1007. Always confirm the mirror mounting type and vehicle build year before ordering to ensure correct fitment.

Function And Typical Failure Modes

The rearview mirror provides a stable field of vision to support safe lane changes and reversing. Common reasons for replacement include impact damage, cracked glass, loosened or damaged mounting button, adhesive failure between the windshield and the mounting plate, or internal degradation from long-term vibration and wear.

Replacement Instructions

Replacement is straightforward for trained mechanics and experienced DIYers. Typical procedure:

• Park the vehicle on a level surface and protect interior trim.
• Remove the plastic trim cover around the mirror mount if present.
• Loosen the retaining screw or depress the release tab and slide the mirror off the mounting button.
• Position the new mirror on the mounting button, align and secure; reattach the trim cover.

Note: After a windshield replacement you may need to replace or re-glue the mirror mounting button to guarantee safe and secure attachment.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: Citroën C2, Citroën C3, Citroën C4; Peugeot 307, Peugeot 1007
• Product Codes: 815340
• Additional Numbers: 815340

If you are a professional mechanic or carrying out a DIY repair, searching by product code 815340 will help you find the correct replacement quickly. This mirror restores safe rear visibility and ensures a neat, factory-like installation.