The Seat Switch Panel is a direct-fit interior trim component designed for Peugeot 407 models. It houses the controls for seat heating and the seat cushion adjustment switches, providing both a finished appearance and protection for the electrical switch gear behind the trim. Ideal for professional garages and experienced DIYers who search by part number (8914CG / 8914CV) when sourcing replacement interior parts.

Key Features And Benefits

– Direct replacement for factory seat switch bezel, restoring OEM look and functionality.
– Designed to accommodate driver and passenger seat cushion controls and seat heater switch openings.
– Quick fitment that saves labor time compared with aftermarket modification.
– Useful part for repairs after wear, broken clips, or cosmetic damage around seat control area.

How It Works

The panel itself is a trim piece that secures the seat switch and provides mounting points for the electrical connector and switch modules. It does not contain the heating element or main switch electronics but protects and aligns them. When correctly installed, the panel ensures button travel is correct and prevents stress on the switch housing and wiring harness.

Installation Recommendations

– Disconnect the vehicle battery before starting to avoid short circuits and accidental airbag deployment when working around seats.
– Use plastic trim tools to carefully release retaining clips to avoid damaging surrounding upholstery and trim.
– Remove the old bezel by unclipping it from the seat frame, disconnect any connectors where present, then refit the new panel by pressing retaining clips into place until audible engagement.
– Inspect switch electrical connectors for corrosion or damaged pins and clean contacts if necessary before reassembly.
– After installation, verify seat heating and adjustment functions at all switch positions. Refasten any removed trim and seat fixings according to manufacturer torque specs.

Why This Part Fails Most Often

Failures are typically due to mechanical wear and environmental exposure rather than electronic faults. Common causes include worn or broken retaining clips from repeated removal, cracked or fatigued plastic from UV and heat near heating elements, liquid spills causing corrosion of switch contacts, and physical damage from impact or improper removal. Symptoms commonly reported are loose or rattling trim, misaligned buttons, intermittent seat heating operation, or visible damage to the bezel.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 407 (Sedan / SW)
• Product Codes: 8914CG, 8914CV
• Other Numbers: NFP (as provided)

Notes For Professionals

This part is commonly searched for by its product codes 8914CG and 8914CV—include these in stock systems and job orders to speed identification. When replacing the bezel during seat repairs, also check the condition of the underlying switch assembly and wiring harness to avoid repeated workshop visits. For thorough repairs, clean or replace corroded connectors and confirm heater element continuity if heating remains intermittent after bezel replacement.

Compatibility And Fitment

Intended primarily for Peugeot 407 models. Confirm visually that the switch layout and mounting points match the vehicle’s existing seat control arrangement before installation. Because this is a trim and switch cover part, fitment is straightforward when matching product codes and switch configuration.

Direct-fit center dashboard air vent assembly with a chrome slider designed for Peugeot 407. Finished in HXN Black Pearl, this unit restores airflow control and interior appearance where the original vent has worn, cracked, or lost its trim. Frequently sought under OE number 9644589777, the part is aimed at professional technicians and experienced DIYers who need a reliable, cosmetically correct replacement for the factory center vents.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 407
• Product Codes: 9644589777
• Additional Numbers: HXN (Color Code)

Function And Benefits

The center air vent controls airflow direction from the HVAC system into the cabin and incorporates the slider control that opens or closes the vent. This unit combines functional restoration with a chrome-trimmed aesthetic, ensuring even air distribution, smooth slider operation, and a factory-like finish that matches dashboards trimmed in Black Pearl (HXN).

How To Replace

1. Prepare basic trim tools and a flat plastic pry tool to avoid damaging the dashboard finish.
2. Carefully pry out the surrounding trim bezel; work gently along the edges to release retaining clips.
3. Unsnap the center vent assembly from the dash and note the positions of any clips or guide tabs.
4. Remove the old vent by releasing its retaining clips and slide out the damaged insert if necessary.
5. Fit the new vent assembly into place, aligning all tabs, and press firmly until clips engage.
6. Reinstall the trim bezel and verify smooth slider operation and correct airflow direction.

Typical replacement time for an experienced technician is short—generally 15–30 minutes for the center vent only, depending on dashboard trim removal complexity.

Installation Recommendations

• Use plastic trim tools to prevent scratches to the dash and vent surfaces.
• Inspect and, if needed, replace any broken retaining clips to ensure a secure fit.
• Lubricate slider contact points with a light silicone spray if the movement feels stiff, avoiding petroleum-based lubricants.
• Check surrounding seals and ducting for dust or debris that could obstruct airflow before final assembly.
• Handle the chrome slider with care to avoid fingerprints or scratches; clean with a microfiber cloth.

Why The Part Most Often Fails

• Plastic Fatigue And Broken Clips: Repeated adjustments and aging can make mounting clips brittle, causing the vent to loosen or fall out.
• Wear Of Slider Mechanism: Daily use and accumulated dust can wear the slider or cause it to jam.
• UV Exposure And Heat: Long-term sun exposure accelerates plastic degradation and color fading, especially on dashboards in sunny climates.
• Impact Or Force: Accidental knocks or forceful removal of trim pieces can crack the vent housing or deform tabs.

Compatibility And Notes

Fits Peugeot 407 center dashboard applications that accept OE part number 9644589777 and are finished in color code HXN (Black Pearl). Many customers search by the OE number when ordering—using 9644589777 will help locate the correct item quickly. The part is a direct exterior/interior trim replacement and does not contain electrical components.

This dashboard ashtray is a direct-fit replacement for Peugeot 407 interiors and is commonly searched by part number 8231NW. Designed for professional workshops and DIY mechanics who need a reliable, OEM-style interior part, it restores the original finish of the dash opening and keeps the cabin tidy. The Black Pearlescent finish (HXN-) matches factory trim tones used in many Peugeot 407 builds.

Key Benefits

– Direct fit to factory dash aperture for easy replacement and clean appearance.
– Factory color match HXN- (Black Pearlescent) for consistent interior aesthetics.
– Simple installation lowers workshop labour time compared to custom repairs.
– Useful spare for refurbishing used vehicles or replacing damaged interior fittings.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 407
• Product Codes: 8231NW NFP
• Additional Numbers: Color Code HXN-

Fitment And Compatibility

Intended For Peugeot 407 models (Sedan, Estate/Sw, Coupe) using the standard dashboard ashtray opening. Frequently looked up by the part number 8231NW, this unit replaces worn, cracked or discolored ashtrays fitted to first-generation 407 interiors.

Installation Recommendations

Recommended For Professional Mechanics And Experienced DIYers. Typical replacement steps:

• Open ashtray and remove any liner or insert.
• Use a plastic trim tool to gently release the surrounding trim clips to avoid damage to the dash finish.
• Unclip the ashtray housing from the dash. If equipped, detach any illumination connector carefully.
• Clean the mounting aperture of debris and ash before fitting the new unit.
• Fit the new ashtray by pushing it into the aperture until all clips engage; reconnect any electrical connector and test illumination (if present).
• Reinstall trim pieces and verify smooth operation of the ashtray lid and any release mechanism.

Use plastic-compatible grease on hinge points if needed to improve smoothness and prevent squeaks. Avoid excessive force on clips; broken clips are the most common fitment damage during installation.

Most Common Reasons For Failure

• Mechanical Wear: Repeated opening and closing causes hinge fatigue and eventual breakage of plastic hinge pins.
• Impact Or Misuse: Forceful closing, slamming, or hitting with objects can crack the lid or housing.
• UV And Ageing: Prolonged sun exposure can make the plastic brittle and discolored over many years.
• Accumulated Dirt And Ash: Built-up debris can jam the mechanism or scratch internal surfaces, leading to poor operation.
• Damaged Clips: During removal, brittle clips can snap, preventing secure refit without replacing the unit.

Replacing the ashtray is a fast, cost-effective way to refresh the interior look of a Peugeot 407 and restore proper function. Search by part number 8231NW to find the correct replacement for your vehicle.

This passenger dashboard airbag is designed specifically for the Peugeot 407 and is an essential component of the SRS safety system. It protects the front-seat passenger in the event of a qualifying frontal impact by rapidly inflating to cushion and reduce the risk of injury. The part is commonly searched by part numbers 9644588880 and 8216CK, making it easy to locate for fast replacement.

Features And Function

The module contains the folded airbag cushion and the pyrotechnic inflator (gas generator) integrated into a single dashboard-mounted assembly. When the airbag control unit detects a severe frontal collision, it triggers the inflator to deploy the cushion in milliseconds. Proper mechanical fixation and correct electrical connection to the SRS wiring are critical for reliable operation. This unit is intended for the front passenger position (dashboard).

Fitment & Compatibility

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 407 (Saloon / Estate (SW) / Coupé) — commonly 2004–2011 production years
• Passenger Position: Front Passenger (Dashboard)
• Commonly Referenced Part Numbers: 9644588880, 8216CK

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 407
• Product Codes: 9644588880, 8216CK
• Additional Numbers: NFP

Installation Recommendations

• Always Disconnect The Battery Before Starting Work And Wait At Least 10 Minutes To Allow The SRS Capacitor To Discharge.
• Follow Manufacturer Procedures For Dashboard Trim Removal; Remove The Glovebox Or Surround Panels Carefully To Access Mounting Bolts.
• Note The Position And Orientation Of The Old Unit Before Removal. Unclip And Disconnect The Airbag Connector(s) Using The Correct Tools And Release Tabs—Do Not Pull On Wires.
• Install The Replacement Unit In The Correct Orientation, Tighten Fasteners To The Specified Torque, And Reconnect The Airbag Connector Securely.
• After Installation, Reconnect The Battery And Verify SRS System Status; If The SRS Warning Light Remains On, Perform Diagnostic Check With Suitable Scan Tool.
• If In Doubt, Have The Final Checks Performed By A Qualified Technician With Proper Diagnostic Equipment.

Why This Part Most Commonly Fails

• Deployment In A Collision: Airbags Are Single-Use Components — Once Deployed They Must Be Replaced.
• Electrical Faults Or Connector Damage: Corrosion, Loose Connections Or Wire Damage Can Prevent Proper Deployment And Trigger The SRS Warning Light.
• Water Ingress Or Interior Damage: Leaks Into The Dashboard Area Can Damage The Module Or Connectors.
• Previous Improper Repairs: Nonstandard Repairs After An Accident Can Compromise The Unit.
• Age-Related Degradation: Although Designed For Long Service Life, Extreme Environmental Conditions Can Affect Wiring And Connectors.

Notes For Mechanics And DIY Enthusiasts

Airbag replacement is safety-critical work. While experienced technicians and competent DIYers can perform the mechanical replacement, the installation must preserve SRS integrity: correct connectors, secure mounting, and verification of the airbag system status with a diagnostic tool. Use the exact part numbers when ordering to ensure correct fitment (9644588880, 8216CK). There is no routine scheduled replacement for airbags; replacement is normally required after deployment or when the unit or its electrical connection is damaged.

Keywords For Search

Peugeot 407 Passenger Airbag, Dashboard Airbag Peugeot 407, 9644588880, 8216CK, SRS Airbag Replacement

Replacement glovebox lid designed for the Peugeot 407, ideal for mechanics and DIY car owners searching by part number (8226J0). This interior trim piece restores the glove compartment’s appearance and function after hinge damage or cosmetic wear. The Mistral Black finish ensures a factory-matching look and seamless fit with the dashboard surfaces.

Features and Benefits

• Direct-fit replacement for a clean OEM appearance and correct alignment.
• Supplied in Color HZD (Mistral Black) to match original interior trims.
• Restores secure closing of the glove compartment and prevents items from falling out while driving.
• Easy to identify by product code 8226J0 — frequently used in searches and parts catalogs.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 407
• Product Codes: 8226J0
• Other Numbers: —

Fitment and Replacement

Typical replacement procedure for a glovebox lid on a Peugeot 407:

• Open the glovebox and empty its contents.
• Support the glovebox door and release any side stoppers or dampers (if fitted) — these are usually held by clips or screws accessible from the glovebox opening.
• Remove fasteners securing the lid to the hinge (screws or plastic retaining clips). Retain any reusable screws; replace broken clips with new ones.
• Detach the old lid from the hinge and fit the new lid, ensuring the latch engagement and hinge pins align correctly.
• Refit dampers/stoppers and test opening/closing action; adjust alignment if necessary to avoid binding.

Installation Recommendations

• Use trim removal tools to avoid damaging surrounding panels and retainers.
• Replace any worn or broken plastic clips and hinge pins during installation for a secure fit.
• Check the latch striker and catch for wear; clean contact areas before assembly for smooth operation.
• Do not overtighten screws — plastic components can crack. Hand-tighten and secure snugly.

Why This Part Most Often Fails

Glovebox lids commonly fail due to broken hinges or plastic retaining clips from repeated use, accidental impacts, or excessive force (e.g., slamming). Long-term exposure to UV and temperature cycles can make interior plastics brittle and more prone to cracking. Cosmetic wear and scratches are also frequent reasons for replacement when restoring interior appearance.

This part is a straightforward, cost-effective repair to restore function and appearance of the glove compartment in Peugeot 407 models. Search by part number 8226J0 for quick identification.

Upgrade your Peugeot 407 interior with this high-quality Center Console Cover, designed to fit around the gear shift lever area. Finished in ALU BRUNITO color, it adds both a sleek aesthetic appeal and practical protection against mechanical wear.

This cover is an ideal replacement for original parts that have been worn or damaged through daily use. The precise fit is guaranteed by genuine OEM product codes, ensuring easy installation with no modifications required.

Technical Information

• Manufacturer: Citroen Peugeot
• Model: Peugeot 407
• Product Codes: 9646824577, 7589A5, 9647822077, 9647822177, 9650233577
• Additional Details: Color HYW- – ALU BRUNITO

Additional Details

Used auto parts like this center console cover offer a cost-effective and environmentally friendly solution for vehicle repairs and restorations. They provide reliable protection for the gear shift area, a frequently touched zone prone to scratches and wear. Regular wear of this component typically occurs due to constant contact with driver hands and gear shifts over time.

Replacing this panel helps maintain interior quality and prolongs the life of your vehicle’s cabin components. Installation is straightforward and can be handled by professional mechanics or skilled DIY enthusiasts familiar with Peugeot interiors.

This replacement radio/display bezel is designed for the Peugeot 407 and provides a direct-fit solution for workshops and DIY mechanics seeking a clean, original-looking finish for the dashboard display. Manufactured in the factory satin silver finish (Satin Argente), the frame secures the instrument display and radio module while restoring the interior appearance after repair or component replacement. Commonly searched by part numbers, the bezel is ideal for technicians who prefer OEM-fit parts to maintain factory alignment and mounting points.

Technical Information

• Manufacturer: Stellantis / Citroen / Peugeot
• Model: Peugeot 407
• Product Codes: 96577887 77, 9657788777
• Additional Numbers: 8265X4 NFP

Function Of The Part

The frame (bezel) surrounds and secures the display and radio module in the instrument panel. It preserves proper positioning of the display, conceals mounting hardware, and provides the finished surface that matches the dashboard trim. Although mainly cosmetic, a correctly aligned bezel prevents rattles and ensures consistent button and screen interaction.

Installation Recommendations

Designed for professional and competent DIY installation. Typical replacement steps:

1. Disconnect the negative battery terminal before any dashboard work to avoid electrical shorts.
2. Carefully remove surrounding trim panels using appropriate trim tools to avoid damaging clips.
3. Unscrew and unclip the old bezel, release any retaining clips, and disconnect any attached switches or illumination connectors.
4. Fit the new bezel by aligning mounting points, press clips into place, and tighten screws to the manufacturer’s torque if applicable.
5. Reconnect any electrical connectors and the battery, then verify correct fit and function of the display and related controls.

Use plastic trim tools and work gently around fragile clips. If the display or radio must be removed, keep screws and fasteners organized to ensure proper reassembly.

Why The Part Most Commonly Fails

• Physical Damage During Repair: Clips or mounting tabs are brittle and often break when trim is removed improperly.
• Wear And Tear: Surface finish can fade or scratch over time from sunlight exposure and regular use.
• Impact Damage: Interior collisions or heavy objects can crack or deform the bezel.
• Poor Previous Repairs: Non-OEM replacements or incorrect refitting can lead to misalignment and additional stress on mounting points.

Order this OEM-fit display frame by referencing the listed product codes to ensure correct match with Peugeot 407 dashboards. Ideal for professional service bays and experienced DIYers who require original fit, finish, and mounting accuracy.

Are you looking for a reliable replacement part for your Peugeot 407? This Steering Wheel Airbag, with product code 96445890ZD and additional number 4112JF, is an ideal choice for replacing the original driver airbag. This part comes directly from Peugeot vehicles, ensuring full compatibility and proper functionality.

Technical Information:

• Manufacturer: PSA Citroen Peugeot
• Model: Peugeot 407
• Product Codes: 96445890ZD
• Additional Numbers: 4112JF

This steering wheel airbag is specifically designed for the Peugeot 407 model and fits the driver’s side steering wheel area. Airbags are a critical component of a vehicle’s safety system, and regular inspection or replacement is vital to maintain maximum protection in case of a collision.

Parts like this steering wheel airbag are often sought after for replacement after deployment in an accident or as a preventive measure during routine vehicle maintenance. Clear product coding and model designation ensure easy and trouble-free installation by professional mechanics or DIY car enthusiasts, especially for older Peugeot models.

Enhancing the safety of your Peugeot 407 with this quality used replacement part is a practical and cost-effective solution without compromising on quality or performance. Don’t hesitate to keep your vehicle in top condition with this essential safety component.

High-quality replacement steering wheel airbag designed for Peugeot 407 models. This driver’s airbag module is commonly searched by part numbers 96445891ZD and 4112HA and provides the primary frontal restraint for the driver in a collision. Ideal for professional garages and experienced DIY mechanics, the module restores SRS protection after deployment or fault diagnosis. The unit should be handled with care and installed by someone familiar with airbag and steering system procedures to ensure safety and correct operation.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 407
• Product Codes: 96445891ZD, 4112HA
• Other Numbers: 96445891ZD; 4112HA

Function and Typical Service Life

The steering wheel airbag is a key component of the Supplemental Restraint System (SRS). It inflates in milliseconds during a qualifying frontal impact to reduce injury to the driver. Airbags have no defined service interval, but they must be replaced after deployment. Faults that trigger the airbag warning lamp (SRS light) indicate that the system should be diagnosed and repaired without delay.

Installation Recommendations

• Always disconnect the battery before starting work and wait at least 10 minutes (manufacturer recommendations may specify up to 30 minutes) to allow residual charge to dissipate.
• Follow the vehicle manufacturer’s removal and installation procedure. Remove trim and steering wheel components carefully to avoid damage to the clockspring (spiral cable).
• When disconnecting electrical connectors, do so gently and avoid bending pins. Do not apply power to the airbag connector outside the vehicle.
• Ensure the clockspring/spiral cable is correctly aligned before fitting the steering wheel; if damaged, replace the clockspring to avoid steering angle or airbag faults.
• Tighten the steering wheel retaining nut/bolt to the manufacturer’s torque specification.
• After installation, clear SRS fault codes and perform a system check with a compatible diagnostic tool; the airbag warning light must extinguish for normal operation.
• Handle and store the airbag module with the padded face upwards, avoid impacts, heat sources and static discharge.

Why This Part Most Commonly Fails

• Deployment in a Collision: Airbags are single-use components and must be replaced after activation.
• Electrical Faults: Damage or wear to the clockspring (spiral cable) or connectors can cause open circuits or short circuits, triggering SRS faults.
• Corrosion or Water Ingress: Moisture in connector areas can lead to intermittent faults or failure to fire.
• Improper Handling During Repairs: Dropping or incorrect storage can damage the inflator or initiator.
• Age-Related Degradation: While not a scheduled wear item, long-term exposure to harsh environments can affect connectors and mounting hardware.

Notes For Mechanics and DIYers

• This part is commonly identified by part numbers 96445891ZD and 4112HA; always verify part numbers against the vehicle’s service literature when possible.
• Replacement often involves steering wheel removal and possibly steering angle sensor recalibration; factor diagnostic and coding time into the job.
• If the airbag has deployed, replace any associated components (clock spring, steering wheel, impact sensors) as required by the vehicle manufacturer.

Product Overview

This genuine-style driver’s knee airbag is designed for the Peugeot 407 and provides additional lower-body protection in frontal collisions. The module is finished in Black Mistral (color code HZD) to match the vehicle interior and is identified by common product codes used for search and fitment.

Key Benefits

• Direct replacement for the original knee airbag location beneath the steering column.
• Improves occupant protection by reducing leg and lower torso injuries during a frontal impact.
• Supplied with factory-style connectors for straightforward installation on compatible vehicles.
• Often searched by product codes—ideal for technicians and DIY enthusiasts who look up parts by number.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 407
• Product Codes: 96445885ZD, 8216CE
• Other Numbers: NFP (as provided)

Compatibility

Designed for Peugeot 407 models. The 407 was produced across several body styles (saloon, SW/estate) and model years; confirm compatibility by matching the product code(s) printed on the original module with the codes above. This listing is aimed at mechanics and experienced DIYers comfortable with airbag replacement procedures.

Function And Typical Failure Modes

The knee airbag deploys during certain frontal-impact events to protect the driver’s knees and lower torso, reducing injury risk and helping to control occupant motion. Common reasons for replacement include:

• Deployment in an accident — airbags are single-use and must be replaced after activation.
• Electrical faults or SRS warning light indicating a circuit/connector issue.
• Physical damage to the module or surrounding trim from impacts or improper handling.
• Corrosion or poor contact at connectors caused by moisture ingress over time.

Replacement Interval

Airbags are generally intended to remain in service for the life of the vehicle unless deployed or a fault is detected. Replace the knee airbag after any deployment or when the SRS system indicates a fault that traces to the module or its wiring.

Installation Recommendations

Installation of SRS components requires care. Recommended steps for qualified personnel or experienced DIYers:

• Disconnect the vehicle battery and wait at least 3–10 minutes (follow manufacturer guidance) to allow capacitors in the SRS system to discharge before beginning work.
• Remove lower dash trim and any retaining fasteners to access the knee airbag module.
• Unplug the airbag connector by releasing the locking tab; avoid pulling on wires.
• Install the replacement module in the correct orientation, secure all fasteners, and reconnect the airbag connector.
• Reconnect the battery and clear SRS fault codes using a diagnostic tool. Verify that the SRS warning light behaves correctly during the ignition cycle.

For safe and reliable results, follow the vehicle manufacturer’s service manual procedures and torque specifications. If unsure, have the replacement performed by a qualified technician.

Why This Part Is Often Replaced

Knee airbags are most commonly replaced after crash deployment. They can also be replaced due to electrical faults, damage to the housing or trim, or connector/corrosion problems that trigger the SRS warning light. Because the module is part of the restraint system, any related fault should be addressed promptly to restore full occupant protection.

Notes For Technicians

• Match product codes 96445885ZD and 8216CE to the original module for correct fitment and interior color match.
• Handle modules carefully and store with the airbag face pointing away from personnel.
• Dispose of deployed or damaged airbag modules according to local regulations.