This Left Side Roof Airbag (driver’s side) is a direct-fit safety component for first‑generation Peugeot 3008 and 5008 vehicles. OEM reference 9801663080 ensures correct fitment and restoration of side-impact protection. Suitable for professional technicians and experienced DIYers who perform body and safety repairs on Peugeot models.

The curtain/roof airbag is a critical part of the side-impact restraint system. It is designed to deploy in significant lateral impacts or rollovers to protect occupants’ heads and upper torsos. Correct installation, routing and anchoring are essential to preserve the deployment geometry and inflation characteristics specified by the manufacturer.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I; Peugeot 5008 I
• Product Codes: 9801663080
• Additional Numbers: Not Available

Compatibility And Replacement Procedure

1. Disconnect the negative battery terminal and wait the time recommended by the vehicle manufacturer before starting work to disable the airbag system.
2. Remove the necessary interior trims and headliner panels carefully to access the curtain airbag module. Preserve trim clips and fasteners; replace any that are damaged or specified as one‑time‑use by the manufacturer.
3. Unbolt the airbag module from its anchors and gently disconnect the electrical connector(s). Avoid pulling on wiring—use the connector release as designed.
4. Fit the new airbag module, ensuring correct alignment and routing. Torque all fasteners to manufacturer specifications and replace one‑time fasteners where required.
5. Reinstall trim, reconnect the battery and use a diagnostic tool to verify the SRS/airbag system status and clear any stored fault codes.

Installation Recommendations

• Work Should Be Performed By A Trained Technician Or An Experienced DIYer Familiar With Airbag Systems.
• Always Follow The Vehicle Manufacturer’s Service Manual And Torque Specifications.
• Replace One‑Time‑Use Fasteners Where Indicated And Use New Clips Or Bolts If Damaged.
• Handle The Airbag Module Carefully; Do Not Attempt To Disassemble Or Repair The Inflator Or Cushion.
• Protect Connectors From Contamination And Ensure Secure, Correct Connections Before Reassembly.

Why This Part Fails Most Often

• Deployment In A Collision: The most common reason for replacement is previous deployment following a side impact or rollover.
• Electrical Or Connector Damage: Wiring damage, poor contacts or connector corrosion—often caused by water ingress from leaks or roof drainage issues—can lead to faults or inhibited deployment.
• Physical Damage During Repairs: Incorrect removal or improper handling when replacing headliner trims can damage the module or its mounting points.
• Age Or Environmental Factors: Long‑term exposure to moisture or contaminants can affect connectors and mounting hardware, triggering SRS faults.

Safety Note: Airbags Are Safety‑Critical Components. Never Attempt To Repair A Deployed Or Damaged Airbag Module—Replace It According To The Manufacturer’s Procedures.

Description

This right side roof (curtain) airbag is a direct-fit safety component intended for the passenger side of first-generation Peugeot 3008 and Peugeot 5008 models. Identified commonly by OE number 9801631380, the curtain airbag deploys from the roof rail in side impacts or rollovers to reduce head and upper-torso injuries. The unit installs along the A- and B-pillar roofline and integrates with the vehicle’s SRS wiring and connectors. Ideal for professional workshops and experienced DIY mechanics who require an OEM-compatible replacement part.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 3008 I, Peugeot 5008 I
• Product Codes: 9801631380
• Additional Numbers: —
• Side: Passenger (Right)

How To Replace

• Disconnect the negative battery terminal and wait at least 10 minutes to allow SRS capacitors to discharge.
• Carefully remove interior trim and headliner sections to access the roof rail mounting points (retain fasteners and clips).
• Unbolt the airbag module from the roof rail, disconnect the SRS connector(s) using careful handling to avoid damaging pins.
• Fit the replacement airbag, secure with the original fasteners to manufacturer torque values, reconnect the SRS connector and reassemble trim.
• After installation, clear airbag faults and verify SRS system status using a suitable diagnostic tool; confirm airbag warning light behavior.

Installation Recommendations

• Always disconnect the battery before starting work and follow the vehicle manufacturer’s safety procedures.
• Handle connectors and inflator housings with care; do not apply power or attempt to test the airbag outside the vehicle.
• Use a diagnostic tool capable of reading and clearing SRS fault codes after fitting; if faults persist, have the vehicle inspected by a qualified technician.
• Replace any damaged trim clips or fasteners to ensure correct fitment and curtain deployment path.
• Recommended for installation by professional workshops or experienced mechanics due to safety-critical nature of the component.

Why This Part Most Often Fails

• Deployment in a previous collision — once deployed the airbag must be replaced.
• Damage to wiring or connectors (corrosion, wear, rodents, or previous improper repairs) leading to SRS faults.
• Physical damage to the inflator or housing from interior work, accidents, or water ingress around trim joints.
• Incorrect removal or reinstallation causing connector pin damage or improper securing of the module.

Compatibility And Notes

Fits first-generation Peugeot 3008 and 5008 models where OE number 9801631380 is specified. Always verify the OE number compatibility from the vehicle’s parts documentation before ordering. This airbag is a safety-critical component; correct fitment and SRS system reset are essential for safe operation.

Product Overview

High-quality left roof-side (curtain) airbag designed for the driver’s side of Peugeot 3008 and 5008 first generation vehicles. This original-equipment style airbag restores side-impact and rollover protection for head and upper torso, helping to ensure occupant safety after repair or accident-related replacement. Suitable for professional workshops and experienced DIY mechanics searching by part numbers 9684667880 or 8335WQ.

Function And Application

The roof-side airbag deploys in side impacts and certain rollover conditions to protect the occupant’s head and side of the torso, reducing the risk of serious injury. It is installed along the roof rail/headliner on the left (driver) side and works together with door and seatbelt systems as part of the vehicle’s SRS (Supplemental Restraint System).

Replacement Procedure

• Disconnect the negative battery terminal and wait at least 10–15 minutes (preferably 15–30 minutes) for residual energy in the SRS system to dissipate.
• Carefully remove interior trim and headliner panels to access the airbag module — preserve clips and fasteners for reassembly.
• Unplug the airbag electrical connector (observe connector locking features) and remove mounting bolts.
• Install the replacement unit in reverse order: secure with correct fastener torque, connect the airbag harness with correct locking, and refit the headliner and trim.
• Reconnect the battery and verify SRS status with a diagnostic tool; clear any stored fault codes and confirm the airbag indicator behaves correctly.

Installation Recommendations

Always follow the manufacturer’s service procedures and torque specifications. Use proper interior trim tools to avoid damaging panels. Never probe or modify airbag connectors or wiring. After replacement, perform an SRS system scan with a compatible diagnostic tool and confirm that no warning lights remain. If unsure, have the final check performed by a qualified technician experienced with Peugeot safety systems.

Why This Part Fails Most Often

Roof-side airbags generally do not have a scheduled replacement interval. Typical causes for replacement are deployment during an accident, physical damage to the module or wiring (including damaged connectors or abrasions during previous repairs), and water ingress or corrosion affecting connectors or inflators. Damage during interior work or improper removal/installation can also render the unit inoperative.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: PEUGEOT 3008 I, PEUGEOT 5008 I
• Product Codes: 9684667880, 8335WQ, 8335.WQ
• Additional Numbers: (T84), (T87)
• Side: Left / Driver’s Side
• Category: Interior Airbag / Side Roof Curtain

Notes For Professionals

This airbag is intended to restore SRS functionality after damage or deployment. After installation, an SRS diagnostic scan is required to confirm circuit integrity and to clear any crash or fault codes. Use original-style connectors and routing to avoid noise or chafing. Keep replacement units in original packaging until installation to avoid contamination or accidental damage.

Description

This right roof side airbag (also known as a side curtain airbag) is intended for the passenger side of first generation Peugeot 3008 and 5008 models. It Protects Occupants In Side Impacts And Rollovers By Providing Head And Upper Torso Cushioning, Reducing The Risk Of Severe Injuries.

Key Benefits

Designed To Fit The Factory Mounting Points For A Direct Replacement When Matched To Correct Part Numbers. Ideal For Professional Workshops And Experienced DIYers Performing Accident Repairs Or Component Replacements. Commonly Searched Under Part Numbers 9684667780, 8335WP, Or 8335.WP.

How The Part Functions

The Roof Side Airbag Is Stored Folded In The Roof Lining And Is Triggered By Side Impact Sensors. On Deployment, The Inflator Rapidly Fills The Cushion To Create A Protective Barrier Between The Occupant And The Side Structure/Glazing. The Module Contains The Cushion, Inflator (Squib), And Electrical Connector To The Vehicle Airbag System.

Replacement Procedure (Overview)

Recommended For Trained Technicians Or Experienced DIYers Only. Basic Steps:

• Disconnect The Battery And Observe The Manufacturer-Recommended Wait Time Before Working On The Airbag System.
• Remove Interior Trim Panels And Headliner Fasteners To Access The Airbag Module.
• Unscrew The Airbag Module Mounting Bolts And Carefully Disconnect The Electrical Connector(s).
• Install The New Unit In Reverse Order, Ensuring Correct Routing Of Any Retaining Clips Or Harnesses And Proper Torque On Fasteners.
• Clear Fault Codes And Verify Airbag System Integrity With A Diagnostic Tool After Reconnection.

Installation Recommendations

Always Follow Manufacturer Safety Procedures. Disconnect The Battery And Allow The System To Discharge For The Time Specified By The Vehicle Manufacturer (Common Practice Is To Wait A Minimum Period Before Handling Airbag Components). Use Correct Tools And Torque Values For Fasteners. After Installation, Check That All Connectors Are Clean, Undamaged, And Fully Seated. Verify System Status With A Diagnostic Scanner To Confirm The Airbag Light Is Extinguished And No Fault Codes Remain.

Why This Part Commonly Fails

• Deployment During An Accident — The Most Common Cause; A Deployed Airbag Must Always Be Replaced.
• Electrical Faults — Damaged Wiring, Corroded Connectors, Or Faulty Inflator Circuits Can Cause The Module To Become Nonfunctional.
• Water Ingress Or Interior Damage — Leaks Around Door Seals Or Sunroof Areas Can Corrode Contacts Or The Module Housing.
• Physical Damage From Previous Repairs — Incorrect Removal Or Impact Damage To Mounting Points Or Wiring Can Prevent Proper Operation.

Compatibility And Fitment Notes

Fits Passenger Side (Right) Roof/Headliner Location On First Generation Peugeot 3008 And 5008. First Generation Production Years Typically Span Peugeot 3008 (2008–2016) And Peugeot 5008 (2009–2016). Confirm Fitment By Matching Part Numbers Listed Below.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I, Peugeot 5008 I
• Product Codes: 9684667780, 8335WP
• Other Numbers: 8335.WP, 8335WP, 9684667780

Final Advice

Airbag Systems Are Safety-Critical. If You Are Not Confident In Performing The Replacement, Have A Professional Technician Carry Out The Work. After Installation, Always Verify The Airbag System With A Diagnostic Tool And Confirm That The SRS Indicator On The Dashboard Returns To Normal Operation.

The airbag is positioned on the driver’s side, ensuring maximum protection during an impact. As a vital safety component, it is essential to replace the airbag if it has been deployed or if there are any signs of damage. Regular vehicle maintenance should include checking airbag functionality to ensure it meets safety standards.

Technical Information

• Manufacturer: PSA
• Model: Peugeot 3008, Peugeot 5008
• Product Codes: 96845302ZE, 4112PF
• Other Numbers: 4112PF

High-quality driver’s side (left) seat-mounted side airbag suitable for first-generation Peugeot 3008 and 5008 models. This airbag module is identified by the common OEM references 9684602480 and 8216XW and is aimed at professional workshops and competent DIYers performing interior safety repairs. The unit restores side-impact protection in the event of previous deployment or damage and is compatible with the original seat mounting points and connector types used by Stellantis/Peugeot.

Key Benefits

• Direct fit for Peugeot 3008 I and Peugeot 5008 I (first generation).
• OEM Reference Numbers Included For Fast Searching: 9684602480, 8216XW.
• Restores Passenger Compartment Side Impact Protection When Properly Installed.
• Suitable For Professional Fitment By Authorized Technicians Or Experienced DIY Mechanics.

Technical Information

• Manufacturer: Stellantis / Peugeot / Citroën
• Model: Peugeot 3008 I; Peugeot 5008 I (First Generation)
• Product Codes: 9684602480; 8216XW
• Additional Numbers: 8216.XW

Function And Typical Failure Modes

The seat side airbag is designed to deploy in a side-impact collision to protect the torso and pelvis of the occupant at the seating position. Airbag modules normally remain passive for the life of the vehicle and require replacement after deployment. Common reasons for replacement or malfunction include:

• Deployment During A Collision — Module Has Been Activated And Must Be Replaced.
• Electrical Or Connector Damage — Corrosion, Broken Pins, Or Harness Chafing May Cause Faults Or Disable Deployment.
• Physical Damage Or Seat Repair Work — Damage From Seat Removal, Spills, Or Impact Can Compromise The Inflator Or Housing.
• Sensor Or Control Unit Faults — Related SRS Wiring Or Crash Sensors May Cause Airbag Warning Lights; The Module Itself Is Replaced If Internally Damaged.

Replacement Frequency

Airbag modules are generally designed to last the service life of a vehicle. Replacement is typically necessary only after activation (deployment) or when diagnosed with a fault or physical damage. Periodic replacement for age alone is not usually required unless specified by manufacturer service bulletins.

Installation Recommendations

• Always Disconnect The Vehicle Battery Before Starting Work And Wait The Manufacturer-Recommended Time To Allow Residual Energy To Dissipate (Typically At Least 10 Minutes).
• Follow Manufacturer Procedures For Seat Removal, Airbag Handling And Torque Settings. Avoid Excessive Force On Connectors And Inflator Housing.
• Inspect Wiring Harness, Connector Pins And Seat Structure For Damage Or Corrosion; Repair Or Replace Damaged Components Before Installing The New Module.
• Use Proper Tools And Anti-Static Precautions. Do Not Probe Airbag Inflator Or Attempt To Service The Inflator Element.
• After Installation, Clear Fault Codes With Suitable Diagnostic Equipment And Confirm SRS System Status. If Airbag Warning Light Persists, Recheck Connections And Related SRS Components.

Advice For Mechanics And DIYers

This part is intended for fitment by trained technicians or experienced DIY mechanics comfortable with SRS systems. Ensure the correct orientation (left/driver side) and OEM part references before installation. Keeping the original part numbers (9684602480, 8216XW) in your search helps locate compatible modules quickly.

Why This Part Is Searched By Part Number

Airbag modules are commonly searched by OEM reference because fitment depends on seat variant, connector type and vehicle wiring. Including the exact product codes (9684602480, 8216XW, 8216.XW) in listings improves search visibility and helps mechanics find the correct replacement faster.

Final Notes

Replace Only With Compatible Modules That Match The Seat Mounting And Connector Layout. Incorrect Installation Or Use Of Incompatible Modules Can Compromise Occupant Safety.

Overview

This passenger airbag module is designed for first-generation Peugeot 3008 and 5008 models. It is a direct-fit safety component intended to replace a deployed or faulty front passenger airbag and restore the original level of occupant protection. The part is suitable for professional workshops and experienced DIY mechanics who understand SRS safety procedures.

Key Benefits

• Direct replacement for the original passenger airbag module for improved safety after deployment or damage.
• Compatible with factory vehicle wiring and mounting points to simplify installation.
• Includes original-style connector interfaces and mounting brackets where applicable.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Peugeot 3008 I; Peugeot 5008 I
• Product Codes: 9684602380
• Other Numbers: 8216XX

Compatibility

Fits first-generation Peugeot 3008 and 5008 models. Verify that the OE part number (9684602380) or the internal code (8216XX) matches the unit being replaced. This airbag is intended as a replacement for the front passenger-side airbag assembly used in these models.

How The Part Works

The passenger airbag is an SRS (Supplemental Restraint System) component that rapidly inflates during moderate to severe frontal impacts to reduce the risk of head and chest injuries for the front-seat passenger. It is triggered by the vehicle crash sensors and fired by the airbag inflator module. After deployment the module must be replaced.

Replacement Procedure (General Guide)

Only experienced technicians or competent DIYers with the correct tools should attempt replacement. Basic steps:

1. Park on a level surface, engage parking brake and remove the key from the ignition.
2. Disconnect the negative battery terminal and wait at least 10 minutes to allow the SRS capacitors to discharge.
3. Remove the trim panels concealing the passenger airbag (dash trim or glovebox components depending on mounting) following manufacturer trim removal methods to avoid damage.
4. Carefully disconnect the airbag electrical connector(s). Note connector orientation and locking tabs.
5. Unbolt the airbag module from its mounting points and remove the unit.
6. Install the replacement module in reverse order, ensuring correct connector seating and secure mounting to specified torque values if available.
7. Reconnect the battery and verify SRS system status with appropriate diagnostic equipment. Clear fault codes if present and confirm that the SRS warning lamp behaves according to the vehicle manual.

Installation Recommendations

• Always disconnect the battery before starting work and wait at least 10 minutes to discharge the system.
• Use correct trim tools to avoid breaking clips or trim pieces.
• Do not probe airbag connectors with test lights that could accidentally trigger the inflator; use a diagnostic tool for system checks.
• Follow manufacturer torque settings for mounting bolts where specified.
• After replacement, use a compatible diagnostic scanner to confirm SRS readiness and clear any stored crash data.
• If you are unsure about any step, seek installation by a trained automotive technician experienced with SRS systems.

Why This Part Most Commonly Fails

The passenger airbag typically only fails because it has deployed during a collision. Other common causes of malfunction include electrical faults such as damaged or corroded connectors, water ingress, previous improper repairs after an accident, or wiring damage from seat removal or interior work. Aging alone rarely causes deployment-capable failure; most service cases are related to prior impact events or connector/wiring issues.

Notes For Buyers

Check the listed product codes (9684602380, 8216XX) against your vehicle’s original unit to ensure compatibility. Proper installation and system verification are essential for occupant safety—replacement without correct diagnostics may leave the SRS system inoperative.