Used original Garrett GTB1449VZ turbocharger for 2.0 HDi (PSA) engines. An ideal replacement for Citroën and Peugeot cars, where this part is often searched for under OEM numbers 0375.P2, 9688361580 and 9677062780. The turbo is fully functional, removed from the car with 148,000 km. Compared to cheap replacements, it is an original Garrett – reliable operation, correct pressure regulation and long service life with proper assembly.

Key benefits
– Original Garrett GTB1449VZ – correct characteristics for 2.0 HDi
– Fully functional condition, suitable for quick and cost-effective repair
– Easy matching by OEM/part number
– Variable geometry (VNT) for fast acceleration even at low revs

Technical information
– Manufacturer/Type: Garrett GTB1449VZ
– Engine application: PSA 2.0 HDi (DW10, diesel), index RH02
– Variable geometry: yes (VNT)
– OEM/PSA numbers: 0375.P2 (0375P2), 9688361580, 9677062780
– Condition: used, tested, fully functional
– Mileage of the donor car: 148,000 km
– Lubrication and cooling: pressure lubrication with engine oil; some versions may also have water cooling – follow the design of your part
– Control actuator: according to the specific version (see the design of your part)
– Package contents: turbocharger in the configuration according to the photos; gaskets, screws and fasteners are usually not included

Compatibility and assembly note
– Typical use: Peugeot 3008 I 2.0 HDi, Peugeot 5008 I 2.0 HDi and other selected Citroën/Peugeot models with 2.0 HDi engine.
– The match of the part number: 0375.P2 / 9688361580 / 9677062780 and type GTB1449VZ is decisive. Please verify by VIN and original turbo code before ordering.
– Installation recommendations: always change the engine oil and oil filter, check and clean/overhaul the oil supply and return, flush the intake tract and intercooler, check the tightness of the intake hoses and the pressure part, check the EGR/DPF and the causes of the previous failure. Fill the turbo with oil before the first start.

Known equivalents and search phrases
– GTB1449VZ, RH02, PSA 0375.P2, 0375P2, 9688361580, 9677062780
– 2.0 HDi Citroën/Peugeot turbocharger, Garrett PSA turbo

Note
– This is a used original part. Please verify compatibility by OEM number and VIN. If you are not sure, we are happy to help you verify compliance.

Original turbo cooling pipe for 2.0 HDi (PSA) engines – water line to/from Garrett turbocharger. Ideal replacement for leaks or damage to the original part. Used original, removed from a car with 148,000 km, fully functional.

Key information and part numbers
– OEM/PSA part number: 037983
– Design code: RH02
– Purpose: 2.0 HDi (DW10) – Garrett turbocharger cooling water line
– Brands/group: Citroën / Peugeot (PSA)
– Condition: used original part, functional, without obvious damage; condition and completeness see photos

Car compatibility (selected 2.0 HDi models)
– Citroën: C4 II, C4 Picasso II, C5 X7, C8
– Peugeot: 3008 I, 5008 I, 807
Note: Compatibility may vary by year of manufacture, emission standard and engine variant. Always verify compliance by part number 037983 or VIN before purchase.

Technical data and features
– Part type: metal turbocharger coolant pipe (feed/return line)
– Function: ensures coolant circulation to stabilize turbo temperature and long bearing life
– Attachment/connection: original shape and connection points according to PSA; fits without modifications to corresponding 2.0 HDi applications
– Compatible with the Garrett turbochargers used in the 2.0 HDi

Why choose this part?
– Original PSA part – precise geometry, secure fit and reliability
– Cost saving compared to a new part, without compromise in function
– Suitable for replacing a turbo, dealing with coolant leaks or pipe corrosion

Installation recommendations
– Always use new sealing rings/O-rings and new copper washers (if available on your model)
– Check the cleanliness and patency of the cooling circuit, ventilate the system properly after assembly
– Observe the tightening torques according to the manufacturer’s service documentation
– Compare the pipe shape and connection points with your original part and with the product photos

Packaging/Contents
– Comes exactly in the configuration shown in the photos (screws and seals only if they are in the photos)

Search Terms (SEO)
– turbo cooling pipe 037983, 2.0 HDi turbo cooling pipe, Citroën Peugeot turbo water line, RH02, PSA 037983, Garrett 2.0 HDi turbo cooling

Fastest way to verify: compare OEM number 037983 and code RH02 with your old part and verify compatibility by VIN.

Used Garrett turbocharger for 2.0 HDI engines, suitable for units with RHR and RHK codes with 88 kW and 100 kW. Ideal replacement for loss of power, increased smoke or whistling turbo. If you are looking for a part by number, verify conformity with codes 9661306080 or 9661567680, or dog 0375L4, 0375L5, 0375L2.

Compatibility is common for family MPVs and commercial vehicles, where the 2.0 HDI works in a challenging mode. Thanks to the corresponding part number, the Turbo is suitable for selected Citroën and Peugeot models and, according to the codes, also for some versions of Fiat Scudo and Fiat Ulysse with a 2.0 HDI engine.

What to watch out for and why Turbo is leaving
The most common causes of turbocharger failures are insufficient lubrication (clogged oil supply, old oil), sucking dirt (leaks in the intake, damaged filter) and excessive engine load. Manifestations of defects are typically whistling or hum, grease in the suction tract, power loss and engine transition to emergency mode. Early replacement protects the engine from further damage.

Mounting Recommendations
Always replace the engine oil and oil filter when replaced, clean or replace the intake and oil leads to the turbo, check the patency of the oil shack and the tightness of the intake and exhaust parts. It is recommended to rinse the suction intercler and use new seals and fasteners. Fill the bearing box with oil before the first start and turn the engine without start to make the turbo pre -establish.

Compatibility (orientation)
Citroën C8, Citroën Jumpy II; Peugeot 807, Peugeot Expert II; Selected versions of Fiat Scudo and Fiat Ulysse with 2.0 HDI according to the codes listed. Always compare the part number with your original turbo.

technical information

• Manufacturer: Garrett
• Model: 2.0 HDI RHR/RHK (88 kW, 100 kW)
• product codes: 9661306080, 9661567680
• Other numbers: 0375L4, 0375L5, 0375L2

Tip for Quick Verification: Compare the Turba label and the stamped/OE number on your original episode with the codes listed above. Match numbers is the most reliable way to trouble -free assembly and proper function.

Turbocharger replacements are often necessary due to wear and tear from high-pressure situations, frequent heating and cooling cycles, and exhaust gas exposure. This unit enhances engine efficiency, power output, and responsiveness, making it an ideal choice for both professional mechanics and car enthusiasts working on their own vehicles.

The installation process involves removing the old turbocharger, which typically requires tools like a socket set and some mechanical knowledge. Ensure proper oil feed and drainage connections are made during installation to maintain optimal performance.

Technical Information:

• Manufacturer: GARRETT
• Model: 2.0 HDI RHR
• Product Codes: 9645919580, 9654919580, 9663201280
• Other Numbers: 0375J1, 0375K1, 0375K8, 0375K9

This Garrett turbocharger is a direct-fit performance replacement for many 2.0 HDi applications. Designed for workshop professionals and experienced DIY mechanics, the unit restores boost response, improves driveability and helps recover lost power caused by a worn or damaged turbo. Commonly searched by OE and aftermarket codes, this turbo suits a range of Citroën and Peugeot models and is compatible with engines bearing RHR, RHE and RHJ codes.

Technical Information

• Manufacturer: Garrett
• Model: 2.0 HDI (Engine Codes: RHR, RHE, RHJ)
• Product Codes: 0375J1, 0375K1, 0375K8, 0375K9
• Other Numbers: 9645919580, 9654919580, 9663201280, 9682778680

Compatibility

Typical vehicle fitment includes, but is not limited to:

• Citroën C4
• Citroën C4 Picasso
• Citroën C5
• Citroën C8
• Peugeot 307
• Peugeot 308
• Peugeot 407
• Peugeot 807

How To Replace

Replacement of a turbocharger on the 2.0 HDi normally follows these general steps. These are guidance points for qualified mechanics and experienced DIYers; always consult the vehicle’s service manual for model-specific procedures and torque values.

• Allow Engine To Cool And Disconnect Battery Before Starting Work.
• Remove Intake Piping, Intercooler Connections And Any Airflow Sensors To Gain Access.
• Disconnect Oil Feed And Return Lines (Prepare To Capture Oil) And Any Coolant Lines If Present.
• Unfasten Actuator, Vacuum Or Electronic Connections And Remove Exhaust Downpipe/Manifold To Free The Turbo.
• Fit New Gaskets And Replace All Seals. Ensure Oil Return Passage Is Clean And Free Of Blockages.
• Refit Components In Reverse Order. Replace Engine Oil And Oil Filter As Part Of The Job.
• Prime Turbo Oil Supply Before First Start (ensure oil feed supplies oil to the turbo and build oil pressure before extended idling or load).
• After Installation, Check For Oil Leaks, Boost Pressure And Normal Operation Under Load.

Installation Recommendations

• Always Use New Gaskets, Clamps And Fasteners Where Required.
• Clean The Oil Return Pipe And Inspect Oil Feed For Any Restriction Or Contamination.
• Replace Engine Oil And Filter During Turbo Replacement To Avoid Early Re-Contamination.
• Check Intercooler And Intake Tract For Oil Residue Or Debris; Clean If Necessary.
• Observe Manufacturer Torque Specifications And Tightening Sequence.
• Run The Engine Up To Operating Temperature And Verify Oil Pressure And Boost Levels; Avoid Heavy Loads For The First Few Miles.

Why This Part Most Commonly Fails

Understanding common failure modes helps prevent repeat damage:

• Oil Starvation Or Contamination: Blocked oil return lines, dirty oil or missed oil changes cause bearing wear and eventual turbo failure.
• Foreign Object Damage: Ingested debris from a damaged air filter or intake damage to compressor/turbine blades.
• Wastegate/Actuator Issues: Faulty actuator or stuck wastegate can cause overboost, reduced performance or mechanical stress.
• Excessive Exhaust Temperatures: EGR or DPF-related issues and prolonged soot build-up increase thermal stress on the turbocharger.
• Oil Leaks: Leaking seals or connections cause loss of lubrication and smoke from the exhaust.

With correct installation, clean oil supply and attention to the intake and exhaust systems, this Garrett turbo can reliably restore engine performance in affected 2.0 HDi RHR/RHE/RHJ applications.

High-quality Garrett turbocharger designed as a direct replacement for 2.0 HDI engines used in a range of Citroën and Peugeot models. This unit restores boost pressure, improves engine response and performance, and is cross-referenced with the common OE and aftermarket codes listed below. Ideal for professional workshops and experienced DIY mechanics searching by part number (e.g. 0375J1, 0375K1) to find a reliable swap for a worn or failed turbo.

Technical Information

• Manufacturer: Garrett
• Model: 2.0 HDI RHR / RHE / RHJ
• Product Codes: 0375J1, 0375K1, 0375K8, 0375K9
• Other Numbers: 9645919580, 9654919580, 9663201280, 9682778680

Compatible Models

Typical fitment includes, but is not necessarily limited to:

• Citroën C4
• Citroën C4 Picasso
• Citroën C5
• Citroën C8
• Peugeot 307
• Peugeot 308
• Peugeot 407
• Peugeot 807

Function and Benefits

The turbocharger uses exhaust gas energy to drive a turbine connected to a compressor wheel that forces more air into the engine. This increases combustion efficiency and torque, particularly at low and mid engine speeds. Benefits include improved throttle response, better driveability and recovery of lost performance compared to a worn unit. The turbo is oil-lubricated and relies on a clean, steady oil supply and proper cooling to function reliably.

Replacement Procedure (Overview)

Replacement should be performed by a qualified mechanic or an experienced DIYer with appropriate tools. General steps:

• Allow the engine to cool. Work on a cold engine to avoid burns.
• Disconnect the battery.
• Remove intake and intercooler piping to access the turbo.
• Drain or isolate coolant if applicable and disconnect coolant lines to the turbo.
• Disconnect oil feed and return lines; be prepared to catch residual oil and replace gaskets.
• Support the turbo and remove mounting nuts/bolts to the exhaust manifold/downpipe.
• Install the replacement turbo with new gaskets, seals and hardware. Use manufacturer torque specifications for fasteners.
• Prime the oil supply before initial start (crank engine with fuel disabled or by other safe priming method) to prevent dry start damage.
• Check for oil, coolant and boost leaks. Start engine, allow to idle until oil pressure stabilizes, then check again and perform a gentle road test.

Installation Recommendations

Always replace turbo oil feed and return gaskets, and inspect the oil lines for blockage or wear. Use fresh engine oil and a new oil filter at installation. Torque all fasteners to the manufacturer’s specification and replace any seized or corroded studs. Prime the turbo’s oiling system before the first start to avoid bearing damage. After installation, avoid heavy loads or high engine speeds for the first few minutes of operation to allow proper oil circulation and seating.

Most Common Failure Reasons

Turbo failures on 2.0 HDI units are most commonly caused by oil-related issues (contamination, coking, oil starvation), foreign object damage from the intake or exhaust side, excessive soot and soot build-up in diesel applications, worn bearings and oil seal leaks. Symptoms include loss of boost, excessive smoke, unusual whining noises, and oil consumption. Regular oil and service intervals, clean air intake, and prompt repairs of oil or cooling leaks help extend turbo life.

Service Life and Notes

Service life varies with maintenance and driving conditions; properly maintained turbochargers on modern diesel engines often exceed 150,000 km, but units exposed to poor maintenance, frequent short trips, or contaminated oil can fail much earlier. Because this product is commonly searched by part number, verify the code (0375J1 / 0375K1 / 0375K8 / 0375K9) and OE cross-references (9645919580, 9654919580, 9663201280, 9682778680) to ensure correct fitment for your engine variant.

This Garrett turbo (760200-5003s) is a direct-fit performance component designed for 2.0 HDI diesel engines used across multiple Stellantis models. It restores boost pressure, improves low-end torque and drivability, and replaces worn or damaged original turbos on vehicles equipped with engine codes RHR, RHE and RHJ. Ideal for professional workshops and experienced DIY mechanics searching by OE or product number (e.g. 0375K8 / 9645919580).

Key Features

• Direct replacement for OEM turbo units on 2.0 HDI RHR / RHE / RHJ engines.
• Garrett manufactured cartridge and bearing system for reliable boost delivery.
• Fits common Citroën and Peugeot applications – simple swap when using correct gaskets and oil/coolant connections.
• Supplied with the turbo core (turbine/charger assembly); actuator or additional parts may vary by variant—check product codes.

Technical Information

• Manufacturer: Garrett
• Model: Turbocharger for 2.0 HDI (RHR / RHE / RHJ)
• Product Codes: 0375J1, 0375K1, 0375K8, 0375K9, 760200-5003s
• Other Numbers: 9645919580, 9654919580, 9663201280, 9682778680

Fitment (Common Applications)

Typical vehicle models where this turbo is fitted include:

• Citroën C4, Citroën C4 Picasso, Citroën C5, Citroën C8
• Peugeot 307, Peugeot 308, Peugeot 407, Peugeot 807

How The Turbo Works

The turbocharger uses exhaust gas energy to drive a turbine that compresses intake air. Increased intake pressure raises engine torque and power while allowing more efficient combustion. Proper oil supply and clean intake/exhaust paths are essential for long turbo life.

Replacement / Installation Overview

• Prepare the vehicle: let the engine cool and relieve intake/exhaust pressure.
• Remove intake piping, intercooler connections (if applicable) and any heat shields obstructing access.
• Disconnect oil feed and return lines and any coolant lines fitted to the turbo; capture fluid and replace gaskets/seals.
• Unbolt the turbo from the exhaust manifold/downpipe and carefully remove; support the turbo to avoid damage to actuator or compressor wheel.
• Transfer any required sensors or actuators if the replacement unit does not include them, and always use new gasket seals on oil/coolant ports and exhaust flange.
• Install the new turbo, reconnect lines, refill/bleed coolant if applicable, and ensure oil feed is unobstructed. Prime the oil system briefly by cranking the engine before the first start to ensure immediate lubrication.
• After installation, run the engine and check for oil/coolant/exhaust leaks, unusual noises or excessive smoke. Allow the turbo to idle until fully at operating temperature before applying load.

Mounting Recommendations

• Always replace oil feed and return gaskets and any exhaust flange gaskets during installation.
• Check and, if necessary, flush oil feed lines to remove sludge or metal particles that could damage the new turbo.
• Use the manufacturer’s recommended engine oil and maintain correct oil level; contaminated or degraded oil is a common cause of failure.
• Do Not Overlook: pre-lubricate the turbo oil gallery before initial start and avoid heavy throttle for the first few minutes of operation after fitting.
• Follow vehicle manufacturer procedures and torque specifications — if unsure, have the installation completed or checked by a qualified technician.

Why This Part Fails Most Often

• Oil Starvation Or Contamination: Dirty oil, blocked feed lines or infrequent oil changes cause bearing wear and premature failure.
• Foreign Object Damage: Ingested debris in the intake or exhaust damages compressor/turbine wheels.
• Excessive Exhaust Temperatures Or Soot Build-Up: Leads to material stress and sticking wastegates or actuators.
• High Mileage And Wear: Bearings and seals wear over time—symptoms include loss of boost, smoke, and unusual noises.
• Improper Installation: Incorrect gaskets, loose connections or failure to prime oil supply can cause immediate or early failure.

Notes For Professionals And Enthusiasts

Search engine friendly product identifiers included in this listing: Garrett 760200-5003s, 0375K8, 9645919580, and related OE numbers—use these when matching replacement parts. Proper diagnosis of boost, oil pressure and exhaust leaks will save time and prevent unnecessary component replacement.