Description

This starter motor is designed for a range of Citroën and Peugeot models equipped with small petrol engines (1.2, 1.4 16V VTI and 1.6 16V VTI). It delivers reliable cranking torque needed for cold starts and regular everyday use. The unit is commonly identified by the manufacturer and part numbers and is frequently searched by these codes when sourcing replacement parts.

Technical Information

• Manufacturer: Stellantis
• Model: Citroën Berlingo B9; Citroën C3 Picasso; Citroën C4 II; Peugeot 207; Peugeot 308; Peugeot Partner Tepee
• Product Codes: M000T32271ZE, 5802AR
• Additional Numbers: 1638135680

Applications

Fits a variety of Citroën and Peugeot small petrol engine vehicles using 1.2, 1.4 16V VTI and 1.6 16V VTI engines. Always verify the part number to ensure compatibility with the engine variant and model year.

How It Works

The starter motor engages the engine flywheel via a pinion gear driven by an electric motor and a solenoid. When the ignition switch is turned, the solenoid pushes the pinion to mesh with the ring gear and closes the high-current circuit to spin the engine. After the engine starts, the pinion retracts and the starter stops.

Replacement Procedure

• Disconnect Negative Battery Terminal: Always disconnect the negative battery cable before starting work to avoid short circuits.
• Access Starter: Depending on the model, the starter is accessible from the engine bay or underneath the vehicle. Raise and securely support the vehicle if working from below.
• Label Electrical Connections: Mark and remove the main power cable and any control wires to avoid reconnection errors.
• Remove Mounting Bolts: Unbolt the starter from the bell housing. Support the starter while removing the final fastener to prevent it from dropping.
• Install New Unit: Position the replacement starter, tighten mounting bolts to manufacturer specification, reconnect electrical connections ensuring clean and tight contacts.
• Final Checks: Reconnect the battery, verify starter engagement and listen for unusual noises. Check for oil leaks or damaged ring gear teeth that could affect operation.

Why Starters Fail

• Worn Brushes and Commutator: Mechanical wear inside the motor reduces performance over time.
• Solenoid Failure: The solenoid can stick or fail electrically, preventing engagement or current flow.
• Contamination: Oil ingress from engine seals or excessive dirt can contaminate internal parts and cause premature wear.
• Electrical Issues: Poor battery condition, corroded terminals, or damaged wiring lead to inadequate cranking current.
• Mechanical Damage: Damaged pinion or ring gear teeth from repeated slipping or incorrect engagement.

Recommended Service Life

Service life depends on driving conditions, climate and maintenance. Typical starters can last many years or well over 100,000 km in normal use, but repeated short trips, frequent cold starts or electrical problems shorten lifespan.

Recommendations For Installation

• Use Correct Tools: Ensure safe lifting and proper sockets; avoid damaging electrical connectors.
• Check Battery Health: Confirm battery voltage and cranking amps before replacing starter to avoid unnecessary replacements.
• Inspect Flywheel Ring Gear: Look for worn or damaged teeth that can cause noise or engagement problems.
• Clean Connections: Clean and tighten battery and starter terminals; apply suitable anti-corrosion treatment to connectors if appropriate.
• Follow Manufacturer Torque Specs: Tighten mounting bolts to the vehicle manufacturer’s recommended torque to ensure proper alignment and sealing.

Note

Part numbers are frequently used to find this starter: M000T32271ZE, 5802AR, 1638135680. Confirm the part code matches the unit required for your engine variant and vehicle model before purchase.

The starter’s primary function is to rotate the engine’s crankshaft to initiate the engine’s operation and maintain its running. It features a position/inclination of R 55, has 9 teeth, a NON terminal, and operates at 12 volts with a power output of 1.2 kW. The rotation direction is clockwise, which is critical for compatibility with the engine’s design.

This starter is an ideal choice for both professional mechanics and self-repair enthusiasts who demand durable and efficient parts for maintaining or restoring vehicle performance. Its compatibility with numerous PSA group models makes it a versatile and valuable replacement part.

Technical Information

Manufacturer: Valeo
Model: Citroën Berlingo, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso; Peugeot 1007, 106, 206, 306, 307, Partner
Product Codes: D6RA572, 5802C9, 5802C6
Additional Numbers: R 55 (position/inclination), 9 (number of teeth), NON (terminal type), 1.2 kW (starter power), 12 V (voltage), clockwise rotation direction

Starters typically wear due to heavy usage, especially in urban stop-and-go driving conditions. Replacing the starter in time ensures reliable engine starts and prevents unexpected breakdowns. Installation involves disconnecting the battery, removing the old starter from the engine block, and securing the new unit with appropriate electrical connections following safety standards.

Choose the Valeo D6RA572 starter to ensure dependable starting performance and enhanced reliability for your Citroën or Peugeot vehicle. Trust in quality components designed to withstand regular wear, providing long-lasting operational stability and peace of mind.

The starter motor plays a critical role in the ignition process by converting electrical energy from the battery into mechanical energy to crank the engine and initiate combustion. This particular unit features a 12-volt operating voltage, a power rating of 1.3 kW, and 9 teeth on the pinion gear, which mesh precisely with the flywheel to ensure smooth engagement. The rotation direction is clockwise, and the starter’s position and inclination are specified as right (R 55), important for correct installation in the engine bay.

Replacement of the starter is typically required when symptoms such as slow engine cranking, unusual noises during start-up, or complete failure to start occur. Common causes of starter failure include worn brushes, damaged pinion gear, defective solenoid, or electrical supply issues. Installation involves disconnecting the battery, removing the faulty starter by detaching mounting bolts and electrical connectors, and fitting the new starter in place before reconnecting all components.

Technical Information

• Manufacturer: CARGO
• Models Compatible: Citroën Berlingo, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso; Peugeot 1007, 106, 206, 306, 307, Partner
• Product Codes: 5802C9, 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6
• Other Numbers: PSA Part Number 9648644680
• Technical Specs: Voltage: 12 V; Power: 1.3 kW; Teeth Number: 9; Rotation Direction: Clockwise; Position/Slope: Right (R 55); Terminal Type: Non-standard (NON)

Premium Valeo Starter Motor Designed For Reliable Engine Cranking On Small-Displacement Petrol Engines. This Starter Is A Direct-Fit Replacement For Many Citroën And Peugeot Models, Matching OEM Reference 9648644680 And Multiple Cross-Reference Codes. Built To Withstand Urban Driving And Frequent Cold-Starts, It Delivers Consistent Engagement And Durable Operation For Professional Garages And Experienced DIYers.

Compatibility

Suitable For The Following Models And Engine Types:

• Citroën C-Elysée
• Citroën C2
• Citroën C3
• Citroën C3 Pluriel
• Citroën Xsara Picasso
• Peugeot 206
• Peugeot 206+
• Peugeot 207
• Peugeot 301

Engine Compatibility: 1.1i, 1.4i, 1.4 16V, 1.6i, 1.6 16V.

Technical Information

• Manufacturer: Valeo
• Model(s): Citroën / Peugeot Small Petrol Engines (1.1i, 1.4i, 1.6i; 1.4 16V, 1.6 16V)
• Product Codes: 9648644680
• Other Numbers: 5802C9, 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6, D6G3

Function And Common Symptoms

The Starter Motor Converts Electrical Energy From The Battery Into Mechanical Rotation To Crank The Engine Until Combustion Begins. Typical Symptoms Indicating Starter Wear Or Failure Include:

• Single Click Or Rapid Clicking When Turning The Key
• Engine Does Not Turn Over Despite Good Battery Voltage
• Slow Cranking Or Intermittent Engagement
• Grinding Noise During Engagement (Indicative Of Worn Bendix Or Flywheel Teeth)

Why The Part Usually Fails

Starter Motors Are Subject To Mechanical And Electrical Stress. The Most Common Causes Of Failure Are Worn Brushes And Commutator, Faulty Solenoid Or Bendix Mechanism, Corrosion And Moisture Ingress, Overheating From Repeated Starts, Or Degraded Connections And Poor Battery/Charging System Condition. Harsh Urban Use With Many Short Trips Accelerates Wear.

Installation Recommendations

Follow These Guidelines For Safe And Reliable Replacement:

• Disconnect The Negative Battery Terminal Before Any Work To Prevent Short Circuits Or Accidental Engagement.
• Raise And Secure The Vehicle On Jack Stands If Necessary. Support The Engine If Required By The Vehicle Procedure.
• Locate The Starter On The Engine Bellhousing, Disconnect The Electrical Connections (Battery Feed And Solenoid Signal) And Remove Mounting Bolts.
• Compare The Replacement Starter With The Old Unit To Confirm Mounting, Electrical Terminals, And Rotation Direction Match.
• Fit The New Starter, Tighten Mounting Bolts Securely, Reconnect Electrical Wires Making Sure All Connections Are Clean And Tight.
• Reconnect The Battery, Start The Engine And Verify Smooth Engagement Without Unusual Noise. Check Charging System If Cranking Remains Weak.
• Where In Doubt, Use A Workshop Manual For Model-Specific Steps And Torque Values, Or Have The Installation Performed By A Qualified Technician.

Durability And Service Advice

Service Life Varies With Driving Style And Environment. Under Typical Conditions Starters Often Last Many Years, But Heavy City Use And Frequent Cold Starts Reduce Lifespan. To Prolong Service Life, Keep Battery And Charging System In Good Condition, Protect Electrical Connections From Corrosion, And Avoid Prolonged Starter Engagement.

Why Choose This Starter

This Valeo Starter Matches Common OEM References For Citroën And Peugeot Small Petrol Engines, Making It A Practical Choice For Professional Repair Shops And Skilled DIY Mechanics Looking For A Direct-Fit Replacement That Restores Reliable Starting Performance.

Overview

This Bosch starter (part number 0001112041) is a direct-fit replacement commonly used on a range of Citroën and Peugeot petrol models. It delivers reliable cranking performance and is suitable for professional workshops and DIY mechanics who require a durable, OE-compatible unit. Customers frequently search by part number (0001112041, 9647982880, 5802M9, 5802EP), so listing reference codes helps find the correct item quickly.

Applications and Compatibility

Compatible with many small to medium Citroën and Peugeot models equipped with 1.0–1.6 petrol engines. Typical applications include:

• Citroën Berlingo
• Citroën C2
• Citroën C3 / C3 Pluriel
• Citroën C4
• Citroën Xsara / Xsara Picasso
• Peugeot 1007
• Peugeot 206
• Peugeot 307
• Peugeot Partner

Function

The starter converts electrical energy from the battery into mechanical rotation to crank the engine. It integrates an electric motor and a solenoid-operated drive (Bendix) that engages the engine flywheel ring gear. Reliable engagement and sufficient torque are essential for cold starts and repeatability in everyday use.

Typical Failure Modes

Starters can fail for several common reasons, which mechanics should be aware of:

• Worn Brushes and Commutator: Gradual wear reduces electrical contact and motor performance.
• Solenoid or Bendix Wear: Solenoid sticking or a worn drive assembly prevents proper engagement.
• Bearing Wear: Noisy operation or seizing can occur from worn bearings.
• Oil or Water Contamination: Leaks or splash can damage windings and mechanical parts.
• Electrical Issues: Poor battery condition, corroded connectors, or weak charging system reduce starter performance.

Replacement Guidance

High-level steps for replacing the starter. These are general instructions—refer to vehicle-specific service literature for exact procedures and torque values.

• Disconnect the negative battery terminal before starting work to avoid short circuits.
• Locate the starter on the engine bell housing or lower engine flank; accessibility varies by model.
• Label and disconnect electrical connections (main battery cable and control wire) and remove mounting bolts while supporting the starter.
• Inspect the flywheel ring gear for damaged teeth and check surrounding wiring and earth straps.
• Fit the replacement starter, tighten mounting bolts to the manufacturer’s specification, reconnect electrical connections, and reattach the battery.
• After installation, verify cranking speed and listen for abnormal noises. Check charging system voltage and battery condition if slow cranking persists.

Maintenance Tips

• Regularly inspect battery condition and terminal cleanliness—poor battery health is a leading cause of starter issues.
• Avoid repeated short trips where the starter is used frequently without allowing the charging system to recharge the battery.
• Check for oil leaks from engine seals that could contaminate the starter housing; repair leaks promptly.

Technical Information

• Manufacturer: Bosch
• Model: Citroën / Peugeot (see compatibility list)
• Product Codes: 0001112041, 1112041
• Additional Numbers: 9647982880, 5802M9, 5802EP

Installation Recommendations

For safe and reliable installation follow workshop best practices: always disconnect the battery before removal, clean and inspect electrical connections, and check the condition of the flywheel ring gear and starter mounting face. If access is tight, support the starter during removal to prevent dropped fasteners. After fitting, confirm correct engine cranking and monitor for any abnormal noises or excessive current draw.

Why This Part Often Fails

Failure is most often caused by electrical wear (brushes and commutator), solenoid or Bendix wear, contamination from oil/water, or stress from a weak battery/charging system. Addressing battery and charging faults early will extend the life of the replacement starter.

Are you looking for a reliable replacement starter for your Citroën or Peugeot vehicles? We offer a starter compatible with various models from both manufacturers. This part has undergone thorough inspection to ensure proper and efficient operation. Guarantee a smooth engine start with this high-quality component.

Technical Information:

Manufacturer: Original Citroën Peugeot Part
Model: Compatible with Citroën Berlingo, Citroën C-Elysée, Citroën C3 Picasso, Citroën C4, Peugeot 207, Peugeot 301, Peugeot 308, Peugeot Partner, and others. Specifically suitable for 1.2 all types, 1.4 16V VTI, and 1.6 16V VTI engines.
Product Codes: M000T32272, V764559480, 1638135680, 1609870380. Supplementary code V764559080.
Additional Numbers: An alternative for original number V764559080.

As a crucial component of your vehicle’s engine system, the starter provides the necessary initial impulse to start the engine. Starters often wear out due to intense usage, especially during cold seasons, which can cause sudden and unexpected failures. Our product, though pre-owned, guarantees reliability and long-term performance due to prior expert inspection and control.

The compatibility across diverse models and engine types makes this starter an ideal choice for Citroën and Peugeot owners. If you are uncertain about compatibility with your vehicle, do not hesitate to contact us for further assistance. Ensure this part matches your car’s specifications for optimal performance.

This starter is ready to give your vehicle a new lease of life. Don’t wait for an unexpected breakdown—secure a dependable replacement today! Suitable for both home mechanics and professional auto technicians, this starter is an excellent solution to keep your vehicle operational.

The starter is an essential component responsible for cranking the engine to initiate ignition. Failure of the starter can result in difficulties starting the vehicle, often causing inconvenient situations especially during urgent departures.

Purchasing this MITSUBISHI starter offers a reliable and cost-effective alternative to original parts without compromising performance. It is built to deliver consistent and durable functionality, ensuring your vehicle starts smoothly every time.

Technical Information

• Manufacturer: MITSUBISHI
• Model Compatibility: CITROËN Berlingo, C2, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso; PEUGEOT 1007, 106, 206, 306, 307, Partner and more
• Product Codes: M000T45071ZT, 5802C9, 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6
• Other Codes: 9656317780

This starter fits a wide range of Citroën and Peugeot models, making it an ideal choice for both professional mechanics and DIY enthusiasts. Due to the complexity of starter replacement, we recommend installation by a qualified technician to ensure optimal performance and reliability.

Whether you are a seasoned mechanic or a car owner repairing your own vehicle, this MITSUBISHI starter is a perfect solution to restore your vehicle’s engine-starting function economically and efficiently.

Do not let a faulty starter limit your mobility. With this dependable MITSUBISHI starter, you benefit from excellent value, proven quality, and long-lasting service life.

The Valeo starter motor is a direct-fit replacement for PSA Citroën & Peugeot petrol engines (1.1i, 1.4i, 1.6i, including 16V variants). It is commonly referenced under manufacturer numbers such as 432623, 5802C9 or PSA 9648644680 and fits a wide range of models. Designed for professional workshops and DIY enthusiasts, this starter delivers reliable engine cranking and straightforward installation.

Key Features

• Voltage: 12 V
• Power: 1.2 kW
• Number of Teeth: 9
• Rotation: Clockwise (CW)
• Mounting Position / Tilt: R 55
• Terminal Type: NON

Compatibility

Fits the following Citroën and Peugeot models (non-exhaustive): Citroën Berlingo, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso; Peugeot 1007, 106, 206, 306, 307, Partner and many others using PSA petrol engines 1.1i, 1.4i, 1.6i and 16V versions.

Installation Guide

Installation is straightforward for experienced mechanics and competent DIYers. General steps:

• Disconnect the negative battery terminal.
• Secure and raise the vehicle as required and locate the starter on the engine bell housing.
• Disconnect electrical connections and remove starter mounting bolts.
• Replace with the new unit, reconnect wiring and tighten mounting bolts to the manufacturer’s specification.
• Reconnect the battery and perform a functional check.

Always follow vehicle manufacturer procedures and safety precautions. If unsure about torque values or access, consult the vehicle service manual.

Common Failure Modes

Starters typically fail due to wear of brushes or commutator, solenoid faults, bearing wear, oil or coolant contamination, or damaged pinion teeth. Symptoms include slow cranking, grinding noises, or no crank. Regular electrical system checks and keeping the engine bay free of leaks prolong starter life.

Technical Information

• Manufacturer: Valeo
• Model: Starter For Citroën & Peugeot 432623 / 5802C9
• Product Codes: 432623, 5802C9
• Additional Numbers: 9648644680, 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6

Compatibility

Fits engines: 1.1i, 1.4i, 1.4 16V, 1.6i, 1.6 16V. Typical vehicle applications include Citroën Berlingo, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso and Peugeot 1007, 106, 206, 306, 307, Partner and other PSA models using the D6G3 starter.

Common Symptoms And Causes

• Engine does not crank or cranks intermittently — often caused by worn brushes, faulty solenoid, or poor electrical connections.
• Grinding or unusual noise when starting — usually indicates pinion engagement or ring gear wear.
• Starter spins but engine does not turn over — can be caused by a failed starter drive (bendix) or weak battery/poor ground.
• Failure over time is typically due to mechanical wear, contamination, or electrical overload from poor battery/charging system condition.

Replacement And Installation

Basic replacement steps (for experienced mechanics or competent DIYers):

1. Disconnect the negative battery terminal before any work.
2. Locate and access the starter motor at the engine/transmission junction. In some models you may need to remove protective covers or components for access.
3. Label and disconnect electrical connections (main positive cable and solenoid connector).
4. Remove mounting bolts and withdraw the starter. Compare the replacement unit to ensure identical flange, mounting holes and electrical terminals.
5. Install the new starter, torque mounting bolts to manufacturer specification, reconnect electrical connections and reconnect the battery.
6. Verify correct operation: check cranking, listen for abnormal noises and ensure secure electrical contacts.

Maintenance And Expected Life

Starters typically last many years but life depends on usage and vehicle electrical condition. Regular inspection of battery health, battery terminals and charging system reduces premature starter wear. Symptoms such as slow cranking or intermittent engagement should be checked promptly to avoid further engine or transmission damage.

Technical Information

• Manufacturer: PSA (Citroën / Peugeot)
• Model: Starter D6G3
• Product Codes: 9648644680, 5802C9
• Other Numbers: 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6

This starter is suitable for professional garages and experienced home mechanics looking for a direct-fit replacement for PSA vehicles. Before ordering, confirm the OEM reference on your original unit to ensure compatibility.

Built for professional workshops and DIY mechanics, this starter balances compact design with proven electrical performance. Quick identification by product code makes ordering simple — many customers search by the part number to ensure fitment. The starter’s compact size and OEM-style mounting simplify installation and reduce downtime in the workshop.

Key Features & Benefits:

• Direct-fit replacement for many Citroën and Peugeot PSA applications.
• 12V electrical system compatibility with 0.9 kW nominal output for reliable starts.
• CW (clockwise) rotation direction matched to original equipment specifications.
• Multiple cross-reference codes for easy identification and ordering.
• Compact design for straightforward installation and long-term serviceability.

Typical Applications:

Fits a variety of petrol engines: 1.1i, 1.4i, 1.6i, 1.4 16V and 1.6 16V. Common vehicle models include Citroën Berlingo, C3, C4, Saxo, Nemo, Xsara, Xsara Picasso and Peugeot 1007, 106, 206, 306, 307, Partner among others. Confirm compatibility by matching the product code with the vehicle’s requirements.

Replacement And Installation Notes:

Before starting any work, disconnect the negative terminal of the battery to prevent electrical short circuits. Typical replacement steps: raise and safely support the vehicle if necessary, locate the starter at the engine/transmission bellhousing, disconnect the wiring harness and battery cable from the starter, remove mounting bolts, replace the unit and reassemble in reverse order. Tighten electrical connections securely and verify starter engagement and engine cranking after installation. If uncertain, consult vehicle-specific workshop manual or a professional technician.

Common Failure Modes & Maintenance Tips:

Starters can fail due to worn brushes or commutator, solenoid malfunction, pinion or ring gear wear, oil contamination, or electrical issues such as poor grounding and degraded battery condition. Frequent short trips, heavy stop-start use or persistent oil leaks can shorten starter life. Regular battery and charging-system checks, clean electrical connections and prompt attention to abnormal noises during cranking will help prevent unexpected failures.

Technical Information

• Manufacturer: Hella
• Model: For Citroën & Peugeot (PSA) 1.1i, 1.4i, 1.6i, 1.4 16V, 1.6 16V
• Product Codes: 8EA011610441
• Additional Numbers: 9648644680, 5802C9, 5802CG, 5802EP, 5802M9, 5802P8, 5802R4, 5802E8, 5802C2, 5802CC, 5802Q1, 5802C6
• Power [kW]: 0.9
• Rotation Direction: Clockwise (CW)
• Voltage [V]: 12

If you need assistance confirming fitment for a specific VIN or engine code, contact our technical support with the vehicle details and part number. This ensures you receive the correct starter for a smooth, reliable replacement.